NDT Inspection Services in New Jersey

Short answer: Atlantis NDT provides non-destructive testing inspection across New Jersey: ultrasonic thickness surveys and corrosion mapping, phased array (PAUT) and TOFD weld inspection, radiography through radiography crews licensed in New Jersey, magnetic particle, penetrant, visual and eddy current testing, plus the NDE that API 510 pressure vessel, API 570 piping and API 653 storage tank programmes rely on. Work is performed by ASNT-certified technicians under ASNT NDT Level III oversight, crews are mobilised to your site, and results arrive as a code-referenced digital report your inspector of record can use.

New Jersey packs an unusual amount of inspection-heavy industry into a small state. The Linden-Carteret-Bayonne waterfront holds a refinery, some of the largest petroleum storage terminals on the East Coast and the northern end of major products pipelines. South Jersey along the Delaware River has another refinery, chemical plants and the Salem and Hope Creek nuclear stations. Between them sit pharmaceutical and specialty-chemical plants, gas utilities, power stations, fabrication shops and some of the busiest bridges and port terminals in the country. New Jersey also adds state rules that many states do not have, including a state boiler and pressure vessel programme, a state discharge-prevention programme and the Toxic Catastrophe Prevention Act. This page maps the market, explains the regulators, and states what Atlantis delivers and what it does not. When you are ready, request a New Jersey inspection quote.

Where inspection work is in New Jersey

Direct answer: New Jersey inspection demand concentrates on the Arthur Kill and Kill Van Kull waterfront from Linden and Carteret to Bayonne and Perth Amboy, at Port Newark-Elizabeth, in the central New Jersey pharmaceutical and chemical belt, along the Delaware River from Trenton and Camden down to Paulsboro, Deepwater and Salem County, and on the state's transmission pipelines, power plants and bridges.

Linden, Carteret, Bayonne and Perth Amboy: the northern refining and terminal belt

The Bayway refinery in Linden sits beside a dense cluster of bulk liquid terminals in Linden, Carteret, Sewaren, Perth Amboy and Bayonne, connected to products pipelines from the Gulf Coast and to barge and ship traffic in New York Harbor. The tank population in this corridor is very large, so API 653 work dominates: MFL floor scanning and UT follow-up on out-of-service tanks, shell thickness surveys and settlement measurements on in-service tanks, and weld inspection on repairs. The refinery itself runs CML thickness surveys on piping, vessel inspections, turnaround weld inspection and CUI screening. Storm surge from Hurricane Sandy in 2012 damaged tanks and terminals along this shoreline, and flood-exposed foundations and tank bottoms remain a reasonable inspection focus. See Linden, Linden refining and Perth Amboy.

Newark, Elizabeth and the Port of New York and New Jersey

Port Newark-Elizabeth is the main container gateway of the Port of New York and New Jersey, with cranes, berths, rail yards and warehousing, while Newark Liberty International Airport adds fuel farms and hydrant systems. Inspection here covers crane and lifting-equipment weld inspection with MT and UT, structural steel, aviation fuel tanks and piping, and industrial plants in the Ironbound and along the Passaic. See refining NDT consulting in Newark and NDT training in Newark.

Central Jersey: pharmaceutical, specialty chemical and manufacturing

From Rahway and Edison through Middlesex, Somerset and Mercer counties, pharmaceutical and specialty-chemical plants operate reactors, high-purity stainless piping, clean-steam generators, boilers, autoclaves and pressure vessels. Inspection here is less about wall loss on carbon steel and more about weld quality on stainless and alloy systems, PT and VT on sanitary welds, UT thickness on utility piping, vessel inspections required by the state's pressure vessel programme, and documentation that satisfies a quality system. Fabrication shops building vessels, skids and spools for these plants need RT, UT, MT and PT to ASME Section VIII and B31.3.

Trenton, Camden and the Delaware River

The Delaware River corridor has steel and metal-working heritage around Trenton, port terminals and industrial plants around Camden and Gloucester City, and power and utility assets. Typical scopes include weld inspection for fabricators and structural steel, thickness surveys at utility and industrial plants, and tank inspection at terminals. See steel NDT consulting in Trenton and practical NDT in Trenton.

Paulsboro, Deepwater and Salem County

Further south, the Paulsboro refinery, the Chambers Works chemical site at Deepwater, marine terminals and the Delaware River port facilities form a second refining and chemical cluster, with pipeline connections around Westville. On Artificial Island in Lower Alloways Creek Township, PSEG's Salem and Hope Creek stations make up one of the largest nuclear generating sites in the country; nuclear plant NDE is controlled by owner programmes and ASME Section XI, so we support those sites only within the owner's qualification requirements. The river ports also host heavy fabrication and offshore-wind-related infrastructure. See Paulsboro, Westville and pipeline NDT consulting in Westville.

Pipelines, power and bridges statewide

Interstate gas transmission lines cross the state, gas utilities run large distribution systems, and products pipelines terminate in the Linden area. Gas-fired power plants and cogeneration units need boiler, HRSG and piping inspection. New Jersey's bridges, operated by NJDOT, the New Jersey Turnpike Authority, the Port Authority and the Delaware River bridge authorities, need structural steel weld inspection on rehabilitation projects. Military installations, including Joint Base McGuire-Dix-Lakehurst and Picatinny Arsenal, add contractor fabrication and facility work.

NDT methods we deliver in New Jersey

Direct answer: Atlantis delivers UT thickness and corrosion mapping, PAUT, TOFD, conventional shear-wave UT, radiography through New Jersey-licensed radiography crews, MT, PT, VT, eddy current and MFL tank floor scanning. The table maps each method to typical New Jersey applications and the code usually cited; final selection is agreed with your inspector of record during scoping.

Every technique runs on a written procedure reviewed by an ASNT NDT Level III, and every technician is certified under an SNT-TC-1A written practice. Where your site requires its own procedures or a qualification demonstration, we work to those. For the New York side of the harbor, see New York tank inspection and New York weld inspection.

API 510, 570 and 653 inspection support in New Jersey

Direct answer: Atlantis performs the NDE that API 510 pressure vessel, API 570 piping and API 653 storage tank inspections rely on, including thickness surveys, weld examination, tank floor scanning and visual examination, and hands documented results to your API-certified Authorized Inspector, who remains the inspector of record and signs the inspection report.

API 510 pressure vessels. New Jersey refineries, chemical and pharmaceutical plants run towers, drums, reactors and exchangers on API 510 programmes, alongside the state's own pressure vessel inspection requirements. We carry out external visual examination, UT thickness at the vessel's CMLs, corrosion mapping where localised loss is expected, PAUT or TOFD on welds with a cracking history or prior repairs, and MT or PT on nozzles and attachments during entries, reported against previous surveys so your inspector can calculate corrosion rates and intervals. See API 510 pressure vessel inspection support.

API 570 piping. Refinery and terminal piping in Linden and Paulsboro, transfer lines between docks and tank farms, and process piping at chemical plants are surveyed against your circuit isometrics, with injection-point, mix-point and deadleg scanning and CUI screening where insulation is removed. Results are delivered per CML so they load into your inspection data system. See API 570 piping inspection support.

API 653 storage tanks. North Jersey's terminals hold one of the highest concentrations of aboveground petroleum storage on the East Coast. For out-of-service inspections we perform MFL floor scanning with UT follow-up, shell course thickness surveys, shell-to-bottom and repair weld examination, nozzle and sump work and floating-roof checks; for external inspections we survey shell thickness, examine roof, shell, foundation and appurtenances, and take settlement measurements presented against API 653 Annex B, which matters on the soft, filled ground common along the waterfront. See API 653 tank inspection support.

What we do not do: Atlantis does not sell risk-based inspection (API 580/581) or fitness-for-service (API 579) assessments, and it does not act as the Authorized Inspector. Our reports give your engineers clean, traceable data; the integrity decisions built on it stay with your programme.

Turnarounds, shutdowns and planned inspection

Direct answer: At New Jersey refineries and chemical plants, inspection volume is planned months ahead around turnarounds, while terminals schedule tanks out of service on rolling programmes. Atlantis joins the planning stage, agrees methods and procedures, and mobilises crews to your site on dates fixed during scoping.

A turnaround scope has three layers. Pre-shutdown, on-stream work covers thickness surveys, external visual inspection and in-service weld examination, and it shrinks the list of items that must be opened. Shutdown work covers vessel internals, tank floors, exchanger shells and welds behind insulation. Post-repair work is the re-examination of every repair weld before start-up. We help you sequence those layers so that scope moves out of the outage window wherever your code and inspector allow.

New Jersey specifics: terminal tank programmes often run back-to-back, so floor scanning and shell work need to keep pace with cleaning and repair contractors; pharmaceutical plants plan shutdowns around production campaigns and validation, so NDE has to fit tight windows and their documentation rules; winter weather affects outdoor PT and MT and couplant choice; and refinery and terminal access requires site-specific safety orientation, TWIC cards at many maritime facilities, and contractor prequalification completed before mobilisation. Plan a New Jersey turnaround or tank programme.

New Jersey regulations that shape inspection

Direct answer: In New Jersey, boilers and pressure vessels are regulated by the Department of Labor and Workforce Development's Office of Boiler and Pressure Vessel Compliance, radiation sources by the Department of Environmental Protection, intrastate gas pipelines by the Board of Public Utilities with PHMSA, process safety by federal OSHA plus the state Toxic Catastrophe Prevention Act, and oil and hazardous-substance storage by NJDEP discharge-prevention rules and EPA SPCC.

Boilers and pressure vessels: NJDOL

New Jersey regulates both boilers and pressure vessels. The Office of Boiler and Pressure Vessel Compliance within the Department of Labor and Workforce Development registers equipment, issues certificates and oversees periodic inspection by state inspectors and authorised insurance or owner-user inspectors, under rules in N.J.A.C. 12:90. That framework expects documented inspection of in-service vessels, and plants generally build their vessel programmes on API 510 and the National Board Inspection Code. NDE data from Atlantis supports those inspections; it does not replace the commissioned inspector. Confirm the status of a specific vessel with the Office.

Radiography: NJDEP and Agreement State status

New Jersey is an NRC Agreement State, so licences for radioactive materials, including industrial radiography sources, are issued and inspected by the New Jersey Department of Environmental Protection's radiation protection programme rather than by the NRC directly. Atlantis does not claim to hold a New Jersey radioactive material licence: radiography on Atlantis scopes is performed by radiography crews licensed in New Jersey, working to reviewed procedures under our Level III. Where exclusion zones would disrupt a live unit, a busy terminal or a dense urban site, PAUT or TOFD may be an alternative if your code and owner accept it.

Pipelines: Board of Public Utilities and PHMSA

The New Jersey Board of Public Utilities runs the state pipeline safety programme for intrastate natural gas pipelines and distribution systems in partnership with PHMSA, which regulates interstate gas and hazardous liquid lines under 49 CFR Parts 192 and 195. Girth-weld inspection on new construction normally follows API 1104. See our pipeline inspection services and pipeline inspection in the New York metro area.

Process safety: OSHA PSM and the Toxic Catastrophe Prevention Act

Private-sector employers in New Jersey fall under federal OSHA, whose process safety management standard (29 CFR 1910.119) requires written inspection and testing procedures, inspection following recognised and generally accepted good engineering practice, and documentation of each inspection for covered equipment. New Jersey adds the Toxic Catastrophe Prevention Act, administered by NJDEP under N.J.A.C. 7:31, which requires risk management programmes at facilities handling extraordinarily hazardous substances, including attention to the mechanical integrity of covered equipment. Owners should confirm their obligations with NJDEP; for inspection, the effect is a strong need for traceable records.

Tanks: discharge prevention and SPCC

Major facilities storing petroleum or hazardous substances are subject to NJDEP's Discharge Prevention, Containment and Countermeasure rules (N.J.A.C. 7:1E) in addition to EPA's SPCC rule (40 CFR Part 112), which expects tank integrity testing to an industry standard such as API 653 or STI SP001. Together they keep tank condition, inspection schedules and documentation in front of New Jersey terminal operators.

Inspection reports clients can use

Direct answer: Every Atlantis inspection in New Jersey produces a digital report built in our own reporting platform: each reading, indication and photo tied to the asset, location, procedure, technician certification and instrument calibration, with acceptance criteria quoted from the governing code. Reports are reviewed under ASNT Level III oversight before release.

Inspectors of record, state boiler inspectors, NJDEP and quality auditors reject reports for predictable reasons: thickness readings that cannot be traced to a CML, indications without a procedure and acceptance criterion, technicians whose certification cannot be shown, and instruments without calibration records. Pharmaceutical clients add their own documentation expectations. Our reporting software is built around those failure points: field capture, offline where needed, structured per asset and location, and exports your inspection data management or quality system can import. Read more on our NDT inspection software page, or compare options in best NDT reporting software 2026.

The data can go further than a PDF. Results can feed scheduling, certification tracking and invoicing in Atlantis ERP (see NDT ERP in Linden and Paulsboro), or be placed on a 3D model of the unit or tank farm in our digital twin platform (see digital twins in Linden and Paulsboro). That route from Level III-led inspection to digital report to optional twin is not offered as one package by the large inspection firms.

Cities we cover across New Jersey

Direct answer: Atlantis mobilises inspection crews to client sites anywhere in New Jersey, from Bergen County to Cape May. Atlantis has no physical office in New Jersey, so crews travel to your plant, terminal, yard or right-of-way, with the schedule agreed during scoping. The pages below cover specific New Jersey cities in more depth.

• Union and Middlesex waterfront:Linden, Linden refining, Perth Amboy, plus Carteret, Sewaren and Rahway by arrangement.
• Essex and Hudson counties:Newark, NDT training in Newark, practical NDT in Newark, NDT ERP in Newark, plus Elizabeth, Bayonne and Jersey City by arrangement.
• Mercer County:Trenton and practical NDT in Trenton.
• Gloucester and Salem counties:Paulsboro, Westville, NDT ERP in Westville, Deepwater and Artificial Island by arrangement.
• Camden and South Jersey: Camden, Gloucester City and Vineland by arrangement.
• Across the harbor:third-party inspection in New York for sites on the New York side.

Related New Jersey hubs: NDT consulting in New Jersey for Level III services, written practices and procedures, and NDT training in New Jersey for ASNT SNT-TC-1A-based technician training.

How to request inspection

Direct answer: Send the asset, method, location, governing code, dates and the deliverable you need. Atlantis replies with clarifying questions or a scoped quote, confirms procedures and technician certifications, mobilises the crew on the agreed date and delivers a Level III-reviewed digital report.

1. Tell us the job. Asset type (vessel, piping, tank, pipeline, structure), method if known, site location in New Jersey, governing code (API 510/570/653, ASME, API 1104, AWS D1.1), target dates, quantity and report format. Send your New Jersey RFQ.
2. Scoping call. We confirm method and technique, access (scaffold, insulation removal, entry permits), site safety and maritime security requirements, and whether radiography or an ultrasonic alternative suits your site.
3. Quote and procedures. You receive a scope and quote, plus the procedures and technician certifications for review by your inspector of record.
4. Mobilisation. Crews complete site orientation and prequalification and mobilise on the date agreed during scoping.
5. Inspection and daily updates. Findings that need immediate attention are reported to your representative the same shift.
6. Report. A Level III-reviewed digital report, traceable to code, procedure, technician and instrument.

Frequently asked questions about NDT inspection in New Jersey

Which NDT inspection services does Atlantis offer in New Jersey?

UT thickness and corrosion mapping, PAUT, TOFD, conventional UT, radiography through New Jersey-licensed radiography crews, MT, PT, VT, ET and MFL tank floor scanning, plus NDE support for API 510, API 570 and API 653 programmes and pipeline inspection, under ASNT Level III oversight.

Do you have an office in New Jersey?

No. Atlantis does not operate a physical office or lab in New Jersey. Crews are mobilised to your site, with the schedule agreed during scoping.

Does New Jersey require pressure vessel inspections?

Yes. The NJDOL Office of Boiler and Pressure Vessel Compliance regulates both boilers and pressure vessels, with periodic inspection by state or authorised inspectors. Our NDE supports those inspections. Confirm specific items with the Office.

Can you perform API 653 tank inspections at New Jersey terminals?

We perform the NDE an API 653 inspection relies on: MFL floor scanning with UT follow-up, shell thickness, weld examination and settlement measurement. Your API 653-certified Authorized Inspector remains the inspector of record and signs the report.

Who regulates industrial radiography in New Jersey?

New Jersey is an NRC Agreement State, so NJDEP licenses radioactive materials, including radiography sources. Radiography on our scopes is done by crews licensed in New Jersey.

Who regulates pipelines in New Jersey?

The Board of Public Utilities runs the state pipeline safety programme for intrastate gas lines with PHMSA; PHMSA regulates interstate pipelines directly under 49 CFR Parts 192 and 195.

What is the Toxic Catastrophe Prevention Act?

A New Jersey law, administered by NJDEP, that requires risk management programmes at facilities handling extraordinarily hazardous substances. It sits alongside federal OSHA PSM and EPA rules and increases the value of complete inspection records.

Can inspection be done without shutting the unit down?

Often, yes. Thickness surveys, external visual, many weld examinations and some corrosion mapping can be done on-stream, subject to temperature limits and site permits, which reduces the scope that must wait for the outage.

How much does NDT inspection cost in New Jersey?

Atlantis quotes on request. Cost depends on method, number of locations or welds, access, travel, crew size, schedule, site security requirements and the report format required. Send the scope and you will get a written quote.

Do you inspect stainless welds at pharmaceutical plants?

Yes. PT, VT and UT on stainless and alloy welds, thickness surveys on utility piping and vessel NDE are part of our scope; we work to your plant's documentation requirements, agreed during scoping.

Will our inspector or auditor accept your reports?

Reports quote the procedure, acceptance criteria and code, list technician certifications and instrument calibration, and are reviewed under ASNT Level III oversight. Agree the format with us during scoping.

Do you offer RBI or fitness-for-service assessments?

No. Atlantis does not sell API 580/581 risk-based inspection or API 579 fitness-for-service assessments. We provide the inspection data those programmes use.

Get a New Jersey inspection scope

Whether you have a terminal tank coming out of service in Carteret, a turnaround weld list in Linden, vessels due for state inspection at a chemical plant, stainless welds at a pharmaceutical site or a refinery outage in Paulsboro, the starting point is the same: tell us the asset, method, code and dates. Get a quote for NDT inspection in New Jersey, or book a call with our ASNT Level III to talk through method selection first. Affordable. Accessible. Fully customizable. Also see all inspection services.

More Atlantis NDT services in New Jersey

• NDT training and certification in New Jersey
• Level III consulting in New Jersey