Ultrasonic Testing (UT) and Thickness Gauging in Newark, New Jersey
Atlantis NDT performs ultrasonic testing in Newark, New Jersey: wall thickness surveys on piping, tanks and vessels, corrosion checks on steel structure, and angle-beam UT inspection of welds. Work is aimed at the container port, the petroleum and chemical terminals around Newark Bay and the Arthur Kill, and the fabrication shops and bridge owners nearby. Send the asset list and the governing code through the quote request form and a Level II technician's scope will come back for your review.
Where ultrasonic testing is used in Newark
Newark sits inside the Port of New York and New Jersey, and the Port Newark–Elizabeth Marine Terminal is the largest part of that port. Every ship-to-shore container crane there is a welded steel structure that carries wind load, boom loads and thousands of lift cycles a year. Thickness readings on boom tubes, legs and sill beams, and angle-beam examination of repaired joints, are routine work for a crane owner trying to keep a terminal open.
A few miles south, the Linden and Elizabeth waterfront holds one of the largest concentrations of refining and petroleum storage on the East Coast. Piping, fractionation towers, drums, heat exchanger shells and aboveground tanks in that corridor all lose wall to corrosion, and UT is the standard way to measure how much. The same method serves the chemical and polymer plants that share the Arthur Kill, and the cold-storage, food and warehouse operations that have grown along the New Jersey Turnpike.
Away from the water, Newark has older industrial building stock, rail yards, bridges over the Passaic River and elevated roadway structure. Thickness surveys on corroded steel members and shear-wave checks on repair welds are common requests from the engineers who maintain these assets. Whatever the asset, the same questions come first: what is it made of, what is its nominal wall, and what code decides whether a reading is acceptable?
What ultrasonic testing finds, and what it cannot
An ultrasonic probe sends a sound pulse into the part and times the echoes that return. For thickness gauging, the delay between the front surface and the back wall gives the remaining wall. For weld work, a probe on an angled wedge sends shear waves through the weld volume and the technician watches for echoes from reflectors such as lack of fusion, cracks and slag. Unlike surface methods, UT reports on the inside of the metal, which is why it is the method of choice for corrosion under insulation checks once the jacketing is opened at a test point and for the root of a thick groove weld.
UT has limits that a good scope states up front. Heavy pitting scatters the sound and can produce a reading that looks plausible but is wrong. Rough, scaled or painted surfaces weaken coupling to the probe. Coarse-grained castings and cast stainless weld metal soak up sound before it returns. Very thin wall under about one-eighth inch needs special probes. And a straight thickness reading says nothing about a crack that runs parallel to the surface, which is a reason to pair UT with surface methods when a component has a cracking history. For that, our Newark magnetic particle page and penetrant page explain the companion examinations.
Codes and acceptance criteria for Newark work
Which document governs a UT job depends on what the asset is. Process piping at a Linden or Elizabeth plant is normally built and maintained to ASME B31.3, with examination methods in paragraph 344 and acceptance in Table 341.3.2. Pressure vessels follow ASME Section VIII, where Division 1 Appendix 12 covers ultrasonic examination of welds. Structural steel for buildings and cranes is usually welded under AWS D1.1, whose Clause 8 includes UT of groove welds and its own acceptance classes. Steel highway and rail bridges fall under AWS D1.5.
The test procedure itself is written to ASME Section V. Article 4 covers weld examination, Article 5 covers UT of materials, and Article 23 carries SE-797, the practice for contact thickness measurement. For plain wall-loss surveys, our guide to Article 5 thickness requirements explains what a defensible procedure must state. Inspection plans for in-service equipment follow the owner's API 510, API 570 or API 653 program. Under those programs the owner's authorized inspector is responsible; Atlantis performs the NDE and reports the thickness and indication data to that inspector.
New Jersey adds its own regime. The Bureau of Boiler and Pressure Vessel Compliance in the state Department of Labor and Workforce Development regulates boilers, pressure vessels and refrigeration systems, issues inspection certificates, and has done so since 1913. An owner-user may run an in-house inspection organization under N.J.A.C. 12:90-3.19. Our New Jersey inspection services hub collects the state-level context in one place.
How ultrasonic thickness testing is performed
On corroded steel, the working tool is a dual-element probe, which has separate transmit and receive crystals angled slightly toward each other. It copes with rough surfaces and pitting far better than a single-element contact probe. Before readings start, the technician calibrates on a step block made of the same material and covering the expected thickness range, then verifies against a known thickness at intervals during the job. An A-scan display stays on the instrument so that a doubled back-wall echo on thin wall, or a laminar split, is recognized rather than recorded as a number.
Readings are taken at the condition monitoring locations the owner has defined, usually marked on an isometric or a vessel sketch. On a pipe elbow the technician grids the extrados, where wall loss concentrates; on a tank shell, courses are measured at set heights. Where the surface is hot, the work needs a high-temperature probe, a couplant rated for the temperature and a correction for how sound speed changes with heat. Insulated lines mean the owner opens a window in the jacketing or has a rigger remove a section before the probe can reach the steel.
For weld examination, the technician builds a reference level from side-drilled holes in a calibration block, selects a 45, 60 or 70 degree shear-wave probe suited to the thickness, and scans both sides of the weld where access allows. Indications are sized against the reference, located by beam path and probe position, and compared with the acceptance table in the governing code. Scanning a weld on a fabricated crane boom or a thick process line takes methodical overlap, and the technician records the extent of scan along with any area that could not be reached.
Who performs the work
Atlantis has no office in Newark. Technicians are mobilized to your site, whether that is a terminal, a plant or a fab shop, for the agreed scope. They are qualified under the company's written practice, which follows ASNT SNT-TC-1A. A Level II technician sets up the instrument, performs the examination and interprets the results. Procedures are approved, and reports reviewed, by an ASNT Level III. The reviewer is our founder, Anoop Rayavarapu, ASNT NDT Level III in UT, RT, MT, PT and VT.
If you need to see how that framework is built before you award work, we can walk you through the written practice and the procedure approval flow. Owners writing their own program can start with written practice development or look at outside Level III consulting. Atlantis is certified to ISO 9001 and ISO 14001.
What the UT report contains
A useful UT report lets a reviewer reproduce the job from the paper. Each report names the component or line number, the drawing or isometric reference, the procedure and its revision, the code and acceptance table applied, the instrument, probe and couplant used, the calibration block and its identification, and the technician with qualification level. Thickness surveys add a grid or table of readings by location with the nominal and minimum required wall, plus the lowest reading highlighted. Weld examinations add the probe angle, scan plan, reference level, scanning gain, and every recordable indication with length, depth and amplitude relative to the reference.
Each indication is dispositioned as acceptable or rejectable against the named criteria, and any area not scanned is stated. Sketches show where each reading or indication sits on the component. Findings go to the owner's authorized inspector or engineer, who decides what the numbers mean for remaining life and next inspection date. Atlantis reports data and does not make the fitness-for-service decision.
Planning a UT job in Newark
Port and terminal sites in Newark run on security rules. Expect credential checks before you reach a berth, safety orientation, and work permits for hot or confined areas. Plant work in Linden and Elizabeth adds site-specific hazard training and, in process areas, gas monitoring. List the people who need access early so the paperwork does not slow the start.
Weather shapes the schedule. January and February bring cold that stiffens couplant and chills instruments; a low-temperature gel, or warming the instrument between readings, usually fixes it. In July and August, steel in sunlight can run hot enough to need a high-temperature setup. Coastal humidity and salt air speed up surface corrosion, so freshly cleaned test points may need re-cleaning after a delay. Turnaround and outage seasons at the refineries concentrate demand in spring and fall, which is a good reason to share your scope early.
Access matters as much as weather. Crane booms, tank roofs and elevated pipe racks need scaffold, a lift or rope-access support from the owner or a contractor. Traffic on the Turnpike and the port's truck gates affects how equipment and people arrive, so build travel buffers into your plan. Because crews travel to site, a clear scope with line numbers or asset IDs avoids lost days.
UT versus MT and PT for your Newark job
Pick the method by the question you are asking. If the concern is wall loss or buried weld flaws, UT is the right tool. If the concern is a surface crack in a ferromagnetic weld, such as a lifting lug or crane pin boss, magnetic particle testing is faster and more sensitive at the surface. If the part is stainless, aluminum or a nonferrous fitting, liquid penetrant testing covers surface-breaking cracks that MT cannot. Many Newark jobs combine two methods on the same weld, for example MT of the cap and UT of the volume.
Our national pages explain each method in more depth: ultrasonic testing, the ultimate UT guide, and the MT versus PT comparison.
Training your own UT technicians
Some Newark owners prefer to build an in-house team. Atlantis teaches theory and practice for the employer to use under its own written practice: see UT Level 1, UT Level 2, and the wider ultrasonic testing training page, or practise on the UT simulator. Under SNT-TC-1A it is the employer who certifies the people who pass. For eligibility questions start at SNT-TC-1A eligibility, and for local options see NDT training in Newark.
Frequently asked questions
What does ultrasonic testing cover in Newark, NJ?
In Newark we perform thickness surveys on piping, vessels, tanks and structural steel, plus angle-beam UT of welds in refinery, terminal, crane and fabrication work. The scope is set by the code, the drawing and the owner.
Can you measure wall thickness on crane booms and port structures?
Yes. Boom tubes, legs and sill members can be gauged with a dual-element probe, provided the owner arranges safe access and the surface is cleaned at each test point. Readings are logged by location against nominal wall.
Which code applies to UT of piping welds at a Linden-area plant?
Process piping is usually governed by ASME B31.3, which points to ASME Section V for method and Table 341.3.2 for acceptance. The owner or its engineer may add stricter limits, and the report names exactly which table was used.
Does ultrasonic testing replace radiography on welds?
Only when the construction code and the owner both permit it. Some codes permit UT of production welds, and AWS D1.1 has its own UT criteria. The substitution is agreed with the owner, engineer and authorized inspector before work starts.
Does Atlantis have an office in Newark?
No. Technicians are mobilized to your site for the agreed scope, so the quote should state the location, access arrangements and any badging the site requires. We reply within one business day.
Who is the inspector of record on API 510, 570 or 653 equipment?
The owner’s authorized inspector. Atlantis performs the examination and delivers thickness grids and indication data to that inspector, who judges remaining life and sets the next inspection date.
Can UT be done on hot piping or insulated lines?
Hot surfaces need a high-temperature probe and couplant, and a correction for sound speed. Insulated lines need the owner to open a window in the jacketing first. We confirm both points when scoping the job.
What information should I send to get a UT quote for a Newark site?
Send the asset or line list, nominal wall, material, operating temperature, the governing code, access details and target dates. Add earlier thickness data if you have it so readings can be compared against a baseline.
Can you train our own technicians in ultrasonic testing?
Yes. Atlantis teaches UT theory and practice for employers building a program under SNT-TC-1A. The employer certifies its own personnel, so completion of a course is one input to that certification and not a certificate by itself.
Inspection and training around Newark
- Magnetic particle inspection (MT) in Newark
- Liquid penetrant testing (PT) in Newark
- Ultrasonic inspection services
- NDT inspection services in New Jersey
UT by industry for Newark: Chemical Processing · Food, Beverage & Pharmaceutical.
UT by job: Ultrasonic pipe thickness testing · Ultrasonic weld inspection · Ultrasonic boiler tube thickness testing · Ultrasonic testing of castings and forgings.
Training your own technicians: UT Level 1 training · UT Level 2 training · NDT training for Newark technicians.
Request an UT inspection quote for Newark
Send the component and material, the quantity, the code or specification and the site address. We reply within one business day with the scope, the mobilization plan and a quote. Request a quote for ultrasonic testing in Newark.
Need ultrasonic testing (UT) done, or learned?
Atlantis provides ultrasonic testing (UT) as an inspection service, trains technicians in it, and lets teams practise it on the Practical NDT simulator.