Magnetic Particle Inspection (MT) in Newark, New Jersey
Atlantis NDT carries out magnetic particle inspection in Newark, New Jersey, on welds, lifting lugs, pins, crane structure and pressure-part attachments made of carbon or low-alloy steel. Mag particle testing is a fast surface check that shows cracks a visual inspection can miss. If your site is in the port, the refinery corridor or a fabrication shop, describe the parts and the code in the MT quote request and we will return a scope for review.
Where magnetic particle testing is used in Newark
Newark's economy is built on moving things. The Port Newark–Elizabeth Marine Terminal handles most of the containers and a large share of the vehicles that enter the Port of New York and New Jersey, and the equipment that does the lifting is steel under repeated load. Spreader attachment points, trolley rail welds, wheel and pin boss welds, twist-lock hardware and the corner castings that tie containers to chassis are all magnetic steel and all classic MT candidates.
Along the Arthur Kill and Newark Bay the work shifts toward process equipment. Weld repairs on pressure vessel shells, nozzle-to-shell welds, support lugs on towers, structural tie-ins on pipe racks and tank shell-to-bottom welds get MT after grinding or after a repair weld cools. Tank farms add a steady stream of requests for floor and shell weld surface checks during outages.
Elsewhere in the city, steel fabricators, rail equipment shops and bridge owners use the method on structural welds. Repairs to steel members on elevated roadway and rail structures often call for MT of the repair weld before the member returns to service. Wherever it is applied, MT answers the same blunt question: is there a crack open to the surface or just under it?
What MT finds, and what it misses
The method depends on magnetism. A magnetic field is induced in the part, and where a crack interrupts the field, a small leakage field forms at the break. Fine iron particles, dusted on dry or carried in a liquid bath, collect at that leakage and outline the crack. The result is immediate and easy to read, and the technician can see length and orientation at once.
Because it relies on magnetic flux, MT works only on ferromagnetic material. Carbon steel and low-alloy steel respond well. Austenitic stainless steel, aluminum, copper alloys and most nickel alloys do not, and a Newark site that mixes stainless piping with carbon steel structure needs both MT and a second method. Our Newark penetrant testing page covers that nonmagnetic side. MT also detects only surface and slightly subsurface flaws; it does not size depth and cannot find buried lack of fusion, which is where ultrasonic testing in Newark comes in.
Surface condition matters. Heavy scale, thick paint, weld spatter and oil all reduce sensitivity, and a coating thicker than the procedure allows can hide a fine crack. The technician checks the surface first and asks the owner to clean or strip where needed.
Codes and acceptance criteria that apply
For MT the method requirements come from ASME Section V, Article 7, with the construction code supplying acceptance limits. Pressure vessels built to ASME Section VIII Division 1 use Appendix 6 for MT methods and acceptance. Process piping under ASME B31.3 relies on paragraph 344.3 for the method and Table 341.3.2 for the limits. Structural steel under AWS D1.1 and bridge steel under AWS D1.5 carry their own visual and surface-examination requirements. ASTM E709 is the guide to the method and ASTM E1444 is the standard practice.
A short explanation of the Article's rules is in our guide to Article 7 magnetic particle requirements. For general background read the complete MT guide.
New Jersey's Bureau of Boiler and Pressure Vessel Compliance, part of the state labor department, regulates pressure equipment in the state and expects repairs to be documented by the rules it enforces. Owner-users with in-house programs operate under N.J.A.C. 12:90-3.19. For the wider state picture see our New Jersey inspection hub. Under API 510, 570 and 653 programs the owner's authorized inspector is accountable; Atlantis performs the MT and supplies the findings.
How magnetic particle inspection is done
The most common field tool is the electromagnetic yoke, which clamps two legs on the part and drives flux between them. Yokes are portable, and the technician repeats the examination with the legs turned roughly ninety degrees so that cracks lying in any direction are caught. Before use the yoke is proved with a lifting-force check: an AC yoke must lift a defined weight at the pole spacing in use, and a DC or permanent-magnet yoke must lift considerably more. Where the part is large or an overall field is wanted, prods or a cable wrap may be specified instead.
Particles come in two main forms. Dry powder in visible colors suits rough weld surfaces outdoors; wet particles in a carrier suit smoother surfaces and give finer sensitivity. Fluorescent wet particles are viewed under UV-A light in a darkened area, which makes tight cracks glow. Colored contrast paint on the surface may be used under visible particles to improve contrast. The technician follows a written procedure for field strength, dwell time, particle application and viewing conditions.
After the examination, parts that will be welded, machined, painted or put into service near sensitive instruments may need demagnetizing to remove residual field. A field indicator or gauss meter confirms the residual level before the part is released. Cleaning removes particles so later coatings adhere.
Typical Newark MT scenarios
Three examples show how the scope usually looks. A crane owner at the port has repaired a cracked weld at a trolley wheel bracket. The repair is ground flush, then examined by wet visible MT with the yoke in two directions, and the owner receives a sketch showing the repaired zone and any residual indication. The record supports the decision to return the crane to service.
A refinery contractor has welded new support lugs on a tower. After the weld cools and the surface is cleaned, the lug-to-shell fillet and the pad edge are examined by yoke, with particular care at the weld toes where fatigue and lack of fusion tend to show. The report goes into the repair package that the owner's authorized inspector reviews.
A fabrication shop in Essex County is building structural steel for a bridge repair under AWS D1.5. A sample of connection welds is checked by MT, including the ends of stiffener welds, before the steel is blasted and painted. In each case the scope names the welds, the percentage to be examined and the acceptance table, so that nothing is left to interpretation on the day.
Who performs the work
Newark has no Atlantis staffing location, so a Level II technician is mobilized to your premises for each job. Personnel are qualified under the company's written practice, built on ASNT SNT-TC-1A. The Level II technician sets up the equipment, performs the MT and interprets it, while an ASNT Level III signs off on procedures and reports. That Level III is the founder, Anoop Rayavarapu, who holds ASNT NDT Level III in UT, RT, MT, PT and VT.
If your own written practice needs work, see written practice development, or talk to us about Level III consulting. Atlantis is certified to ISO 9001 and ISO 14001.
What the MT report contains
A complete MT report identifies the component, drawing or weld number, the procedure and its revision, and the code and acceptance table. It lists the method used (yoke, prods, wet or dry, visible or fluorescent), the particle product and batch, the equipment and its calibration or lift-test status, the field direction and surface condition, and the technician and level. Each indication is recorded with location, length and orientation, and marked on a sketch or photograph. Every indication is dispositioned against the acceptance criteria named in the contract, and the report states whether the part was demagnetized.
The report is reviewed and signed before it is released. We hand the data to the owner or engineer who decides on repair, re-test or release.
Planning a Newark MT job
Winter is the main constraint here. Wet particle baths and contrast paints are formulated for a working range, and very cold steel can slow particle mobility or make the carrier thicken. The procedure sets the range, and a technician may warm the part or switch products when Newark cold falls below it. Summer heat is the opposite problem: hot steel dries a wet bath too fast and can dull fluorescence.
Fluorescent work needs darkness, which is awkward outdoors in a terminal in daytime. A portable shroud, a tent or a night shift on the owner's side usually solves it. On the port and in plants, expect badging, orientation and work permits. Rail and truck traffic at gates affects when crews can enter.
Refinery and tank-farm outages concentrate MT demand in spring and fall, so early scoping helps. Provide access, a clean test surface, and power if prods or a bench unit are specified.
Common reasons a magnetic particle result is questioned
Most disputes over MT come from procedure details rather than from the method. A yoke used at wider pole spacing than it was lift-tested for, a part examined in only one direction, particles applied before the surface was dry, fluorescent light too weak or ambient light too strong, and an indication read without the lighting the procedure specified are all typical. Non-relevant indications from a sharp change in section or a magnetic writing on the part can be mistaken for cracks, and the technician should be able to show how each was identified and resolved, for example by re-magnetizing after demagnetizing.
A good record prevents the argument. The report states the field direction, the verification of yoke strength, the lighting measurement and the particle batch, so a reviewer can see that the examination was done the way the procedure required. Where an indication is borderline, the technician flags it for Level III review instead of deciding alone.
MT versus PT and UT in Newark
Choose MT when the part is magnetic and the concern is a surface or near-surface crack: welds on crane steel, pins, lugs and vessel attachments. Choose penetrant testing when the part is stainless, aluminum or any nonmagnetic alloy, or when the surface is too rough for particles. Choose ultrasonic testing when the concern is wall loss or a flaw below the surface. Our MT versus PT comparison sets out the trade-offs, and the national MT page covers the method in more depth.
Training your own MT technicians
For owners who want in-house capability, we teach MT Level 1 and MT Level 2 under the wider magnetic particle testing training program. Employers certify under SNT-TC-1A; our courses supply the theory and practice. See NDT training in Newark and practice tests for exam preparation.
Frequently asked questions
What parts can you inspect with magnetic particle testing in Newark?
Welds, lugs, pins, crane and equipment steel, vessel attachments and structural members made of carbon or low-alloy steel. Parts must be ferromagnetic and the surface must be clean enough for particles to move.
Does MT work on stainless steel pipe or aluminum fittings?
No. Austenitic stainless steel and aluminum are not magnetic, so particles will not outline cracks. Liquid penetrant testing is the usual surface method for those materials in Newark plants and shops.
Which standard governs MT of welds on pressure vessels?
ASME Section V Article 7 sets the method, and ASME Section VIII Division 1 Appendix 6 gives MT methods and acceptance for vessels. Piping under B31.3 uses its own paragraph 344.3 and Table 341.3.2.
Do you use fluorescent particles outdoors at port sites?
Fluorescent MT needs a darkened area and UV-A light, so outdoors we use shrouds or tents when the procedure calls for it. Visible dry or wet particles are the alternative for bright locations.
Does Atlantis have an office or lab in Newark?
No. A technician is mobilized to the address you give for the agreed scope. Please send the location, access rules and any badging requirements with your quote request and we reply within one business day.
Is demagnetizing included after MT?
It is done when the procedure or the owner requires it, for example before welding, machining or coating. A gauss or field-indicator check confirms the residual field, and the report records the result.
How does cold weather in Newark affect magnetic particle testing?
Procedures set a working temperature range for particles and carriers. In a hard winter we warm the part, change product or use dry particles, and record the surface temperature in the report.
What do I need to send for an MT quote?
Send the part list or weld map, material, surface condition and coating, governing code and acceptance table, access arrangements and target dates. A photograph of a typical weld helps us plan technique and equipment.
Can you train our technicians in MT?
Yes. We offer MT Level 1 and Level 2 training for employers that certify under SNT-TC-1A. The employer certifies its own people, and our training supplies the theory and hands-on practice.
Inspection and training around Newark
- Ultrasonic testing (UT) in Newark
- Liquid penetrant testing (PT) in Newark
- Magnetic particle inspection services
- NDT inspection services in New Jersey
MT by industry for Newark: Chemical Processing.
MT by job: Magnetic particle weld inspection · Magnetic particle inspection of lifting equipment · Magnetic particle inspection of castings and forgings · Magnetic particle inspection of structural steel and bridges.
Training your own technicians: MT Level 1 training · MT Level 2 training · NDT training for Newark technicians.
Request an MT inspection quote for Newark
Send the component and material, the quantity, the code or specification and the site address. We reply within one business day with the scope, the mobilization plan and a quote. Request a quote for magnetic particle inspection in Newark.
Need magnetic particle testing (MT) done, or learned?
Atlantis provides magnetic particle testing (MT) as an inspection service, trains technicians in it, and lets teams practise it on the Practical NDT simulator.