SNT-TC-1A for Aerospace NDT: What the Programme Needs on Top of the Baseline
SNT-TC-1A gives an aerospace NDT programme its baseline: recommended training and experience hours by method, general, specific and practical examinations, vision checks and employer certification under a written practice. Penetrant takes 4 training hours at Level I and 12 cumulative to Level II; ultrasonic, radiography and eddy current take 40 per level. Aerospace work adds purchase-order flow-down, prime process specifications and Nadcap AC7114 on top.
SNT-TC-1A is ASNT's recommended practice, and the employer's written practice gives it force; customers then audit the firm against that written practice. Its recommended training runs lowest in the surface methods, 12 cumulative hours to Level II in penetrant and 20 in magnetic particle, against 80 for ultrasonic, radiography and eddy current. What aerospace adds is mostly specificity rather than a different structure: which specification governs each line of the written practice, practical specimens representative of aerospace hardware, technique limits on each certificate, procedures and technique sheets approved by a Level III qualified in the method, and records that survive Nadcap AC7114 sampling. Where a purchase order or prime specification sets a higher figure or names a particular qualification basis, the written practice carries it. Repair stations add FAA 14 CFR Part 145. Read the purchase order first; it decides what the programme has to show.
Source: ASNT Recommended Practice No. SNT-TC-1A (2024), with Addendum (effective May 2025), Table 6.3.1A; PRI Nadcap audit criteria AC7114 for nondestructive testing; FAA 14 CFR Part 145, §145.163 (repair station training programme)
| Method | SNT-TC-1A Level I | SNT-TC-1A cumulative to Level II | Experience in method, direct to Level II | Aerospace layer on top |
|---|---|---|---|---|
| Liquid penetrant (PT) | 4 hrs | 12 hrs | 210 hrs | ASTM E1417 fluorescent penetrant with AMS 2644 materials; practicals on fine cracks in the alloys you process |
| Magnetic particle (MT) | 12 hrs | 20 hrs | 280 hrs | ASTM E1444; practicals on steel parts with known indications and the system checks the specification calls for |
| Ultrasonic (UT) | 40 hrs | 80 hrs | 840 hrs | ASTM E2375 or AMS-STD-2154 for wrought product; technique sheets per part; phased array defined in the written practice |
| Eddy current (ET) | 40 hrs | 80 hrs | 840 hrs | Surface, bolt-hole and conductivity techniques stated on the certificate; aerospace reference standards |
| Radiography (RT) | 40 hrs | 80 hrs | 840 hrs | ASTM E1742; film, computed and digital radiography trained and examined per modality |
| Visual (VT) | 8 hrs | 24 hrs | 210 hrs | Scope from the prime's specification or the maintenance data; borescope as a separately qualified technique |
The baseline SNT-TC-1A gives an aerospace programme
SNT-TC-1A is ASNT's recommended practice for qualifying and certifying NDT personnel. It is not law and nobody enforces it directly: it becomes binding when a code, customer or regulator invokes it, and for an aerospace supplier the invoking document is the customer's purchase order. Its tables carry no force until an employer adopts them through a written practice.
The written practice is the instrument. It documents how the company trains, examines, certifies and recertifies each level in each method, it is approved by the employer's NDT Level III, and it is retained on file. Customers then audit the firm against that document rather than against SNT-TC-1A, which is why an aerospace written practice has to say, method by method, where a customer requirement sits on top of the recommended figure.
That gives an aerospace programme a solid floor and a clear place to build. The baseline handles the structure every programme needs: training, experience, three examinations, vision and recertification. The aerospace layer handles what the hardware and the customer demand, and the rest of this page is that layer. The full requirement set is broken down under aerospace NDT certification requirements.
Training hours: the baseline numbers by method
Liquid penetrant carries the lowest recommended training: 4 hours at Level I and 8 more at Level II, 12 cumulative. Magnetic particle runs 12 and 8, 20 cumulative. Visual is 8 and 16, 24 cumulative. Ultrasonic, eddy current and radiography each take 40 hours per level, 80 cumulative. A candidate going straight to Level II without time at Level I completes the sum of both levels.
For aerospace work the surface-method figures are the first to check against the customer. Fluorescent penetrant on rotating engine parts and magnetic particle on landing gear are fracture-critical work delivered on the methods with the shortest recommended courses. Where the purchase order or process specification asks for more, the written practice has to carry the higher figure, and the course record has to show content, instructor and hours.
Training content should trace to the ANSI/ASNT CP-105 topical outlines that ASNT recommends using with SNT-TC-1A. Per-method detail for every technique sits in NDT training hours by method, and the SNT-TC-1A eligibility checker compares a candidate's documented hours with the recommended minimums.
Experience hours: what counts and what an aerospace auditor traces
SNT-TC-1A recommends experience in the method: 210 hours at Level I plus 630 at Level II for ultrasonic, radiography and eddy current, 840 in all; 70 plus 210 for magnetic particle; 70 plus 140 for penetrant and visual. Level II experience is treated as time spent at Level I or equivalent, and the written practice may also set a minimum of total NDT experience across all methods.
What does not count matters as much. Training hours, practical course hours and simulator time are not experience, however realistic the simulator. Experience is hours worked in the method, documented in experience letters and logs.
Aerospace auditors trace those hours. A log with dates, method, work performed and supervisor attestation survives; one retrospective line reading "requirements met" does not. Logging the part types and techniques worked turns the same hours into evidence for a technique-limited certificate. The documentation rules, entry formats and reconstruction paths are in NDT OJT hours log requirements.
What aerospace adds: specimens, techniques and the specification trail
The examination structure stays the same: general, specific and practical, administered by a Level III, with a recommended composite of at least 80 percent and no single examination below 70. What changes is content. The specific examination should test the prime's process specification and the shop's own procedures and technique sheets. The practical should use specimens representative of the parts, alloys and discontinuities the technician will actually inspect, with a documented key.
Certificates should carry technique limits. Bolt-hole eddy current, immersion ultrasonics, fluorescent penetrant on rotating parts and digital radiography are different jobs, and an aerospace written practice can restrict each certification to the techniques the person is qualified for. Procedures and technique sheets in the audited scope need approval from a Level III qualified in that method, and a technique sheet revised without re-approval is a classic finding.
Two 2024-edition points matter here too. The employer must assess whether externally referenced examinations meet its requirements before relying on them, and written-examination proctors are expected to be trained. Both bite on aerospace programmes that buy in training or examination services.
Which requirement binds you: the contract decides
Stop asking which document is better and read your purchase orders. If you machine, process or inspect hardware that ends up on an airframe or engine, the prime's quality clauses flow its NDT requirements down to you, and Nadcap AC7114 audits check that you meet them. Defense subcontracts under the major aerospace primes carry similar flow-down. The contract names what your personnel qualification has to satisfy.
Much of US heavy industry runs on the ASNT documents as well. ASME Code fabrication, AWS D1.1 structural work and API inspection-code work reference employer-based certification per SNT-TC-1A, or ANSI/ASNT CP-189 when the contract names it; the SNT-TC-1A vs CP-189 comparison covers that choice.
For a shop serving both markets, that makes SNT-TC-1A the common spine. Atlantis builds the aerospace written practice on ASNT SNT-TC-1A and aligns it to the purchase-order flow-down, the prime's specifications and Nadcap AC7114, so industrial and aerospace personnel certify under one document. Where an aerospace customer names a particular qualification basis or a higher figure, that requirement goes into the written practice for that customer's work.
The Level III role in an aerospace programme
SNT-TC-1A puts programme authority with the employer's NDT Level III: the person who approves the written practice, procedures and examinations, and whose signature an auditor traces back from every certificate. Aerospace programmes often call that person the Responsible Level III, and primes and Nadcap assessors review the person, not just the paperwork. The Level III must be qualified in each method they sign for.
Small and mid-size aerospace suppliers rarely carry that role on payroll, which is why the outside agency model exists. A contracted Level III can write and approve the written practice, build and grade examinations and recommend certification, while the employer signs and issues the certificate. Auditors ask for the outside-agency agreement plus that person's credentials. The scope and engagement structure are set out under ASNT Level III consulting for aerospace programmes.
Running aerospace and industrial work under one written practice
Dual-market shops make one early documentation choice: two written practices, or one SNT-TC-1A document with aerospace requirements identified by method. One document wins on maintenance, since examination, vision and recertification mechanics are the same either way, and revisions stay in one place. Each certificate must state method, level, technique and scope limits; a certificate that does not is a finding in either market.
Cross-crediting is where merged programmes go wrong. Training delivered as a documented course with an outline, a qualified instructor and attendance records credits cleanly everywhere. Informal shop-floor familiarisation logged as training credits nowhere an auditor looks closely. Build the training file to the aerospace evidentiary standard from day one, and both sides of the business draw from the same folder without a finding.
What the aerospace layer takes, and where to get help
Plan the aerospace layer in schedule, not sentiment. The hour table is shared; the extra work sits in the specimen library, the technique sheets, customer-specific examination content and audit-ready records. Surface-method-heavy shops feel more of it because their recommended courses are the shortest; UT-centric shops feel it in technique sheets and specimens rather than in hours.
Atlantis provides ASNT NDT Level III consulting for aerospace: written practice development, procedures, technique sheets, examinations and Nadcap AC7114 audit readiness, with the option of acting as your outside agency Level III in UT, RT, MT, PT and VT. We deliver ASNT SNT-TC-1A-based Level I and II method training for aerospace and aviation teams, ASNT Level III exam preparation, and NDT inspection services for aerospace and aviation. Quote on request: request a programme review and start from the requirements your customers actually invoke.
Which document governs aerospace NDT personnel qualification?
The purchase order decides. Primes flow their requirements down through purchase-order quality clauses and process specifications, and Nadcap AC7114 audits check the supplier against them. Atlantis builds the aerospace written practice on ASNT SNT-TC-1A and aligns it to that flow-down, the prime's specifications and AC7114. Where a customer names a particular qualification basis or adds its own requirements, the written practice has to carry them; read the clauses before assuming.
How many training hours does SNT-TC-1A recommend for penetrant testing?
Four formal hours at Level I and eight more at Level II, 12 cumulative; a candidate certifying directly to Level II owes the full 12 up front, plus 210 hours of experience in the method. These are recommended minimums. An aerospace written practice covering fluorescent penetrant on critical parts sets its own figure, and where the customer's specification asks for more, that is the figure auditors check.
Is SNT-TC-1A mandatory or only recommended?
SNT-TC-1A is a recommended practice. It binds no one until an employer adopts it through a written practice, or a code, customer or regulator invokes it: ASME Boiler and Pressure Vessel Code Sections V and VIII, AWS D1.1, the API inspection codes and prime purchase orders all do. Once it is adopted, customers audit the firm against its own written practice rather than against the standard directly.
Can one written practice cover aerospace and industrial work?
Yes. One SNT-TC-1A document with aerospace requirements identified by method is the lower-maintenance structure, since examination, vision and recertification mechanics stay the same. Each certificate must state method, level, technique and scope limits, and training records must meet the aerospace evidentiary bar for any hours claimed on the aerospace side. Customer requirements belong in the document, not in a side letter.
What examinations does an aerospace candidate sit under SNT-TC-1A?
A general examination on the principles of the method, a specific examination on the procedures, codes and equipment the person will use, and a practical examination on real specimens, administered by a Level III and never by the candidate or a subordinate. The recommended composite is at least 80 percent with no single examination below 70. In aerospace the specific examination should cover the prime's specification and the practical should use representative aerospace parts.
How do experience hours work for aerospace candidates?
SNT-TC-1A recommends experience in the method: 840 hours direct to Level II for ultrasonic, radiography and eddy current, 280 for magnetic particle, and 210 for penetrant and visual. Training, practical course and simulator hours do not count, and the written practice may add a minimum of total NDT experience across methods. Aerospace auditors trace those hours to dated, attested logs, ideally naming the part types worked.
Get certified, or certify your team
Individuals train and sit examinations under their employer's written practice. Employers need that written practice, and a Level III to run it. Atlantis does both.
NAS 410: how it works and how it compares
Two plain-language explainers on the aerospace NDT personnel standard NAS 410: how certification works under it, and how it differs from ASNT SNT-TC-1A.
Free written-practice gap check by an ASNT Level III
For employers certifying technicians under ASNT SNT-TC-1A: Anoop Rayavarapu, ASNT NDT Level III, will check your written practice against SNT-TC-1A — training and experience hours, exam composition, vision exams, recertification and Level III responsibilities — and tell you where the gaps are. Request a written-practice gap check.
Useful references: training requirements matrix, NDT written practice template.