Magnetic Particle Inspection (MT) in Mobile, Alabama

Atlantis NDT sends Level II magnetic particle technicians to Mobile, Alabama to check carbon and low-alloy steel for surface and near-surface cracks. Typical scopes are weld toes on structural steel and crane pedestals, repaired areas on pressure equipment, lifting gear, fabrication welds and heavy rolling-stock or port machinery. Tell us the component, the code and the surface condition, then request an MT inspection quote for Mobile.

Where magnetic particle testing is used around Mobile

Mobile combines shipbuilding, steel production, chemical plants, paper mills and a busy port, and nearly all of that equipment is ferromagnetic steel. That is the ideal case for MT. Fabricators building hull sections, deck structures and equipment foundations use it to check fillet and groove welds for toe cracks and arc strikes. Repair yards grind out suspected cracks and use MT to prove the cavity is clean before welding resumes.

At the docks, heavy cargo handling concentrates stress in a few places. Crane booms, slewing rings, pedestal welds, spreader bars, shackles, hooks and padeyes all see cyclic loading, and fatigue cracks start at welds and sharp changes of section. A magnetic particle check at those points during a planned inspection can find cracks while they are still short. Industrial plants add pressure vessel nozzle welds, support lugs, structural pipe racks, and the attachment welds on tanks and heat exchangers.

Steel mills and metal fabricators around the area also run rotating and rolling equipment where shafts, rolls and gear teeth are examined for service cracks. For the broader national scope see our magnetic particle testing service page; this page explains how the method fits Mobile jobs.

What MT finds and what it misses

Magnetic particle inspection works by magnetizing the part, so that any surface or slightly subsurface discontinuity distorts the magnetic field and attracts fine ferromagnetic particles. The particles gather over the flaw and form a visible line. Because the method depends on magnetism, it applies only to ferromagnetic material such as carbon steel and low-alloy steel. It does not work on austenitic stainless steel, aluminum, copper or most nickel alloys, which are common in marine and chemical settings. Those parts need liquid penetrant testing instead.

The method is strongest on flaws that lie across the magnetic field. A crack running parallel to the field lines may produce no indication at all, which is why the part is magnetized in two directions. Depth sensitivity falls quickly below the surface, so MT is a surface and near-surface method; it will not size a deep embedded flaw. Thick paint, weld spatter and rust weaken indications, and excessive coating may require removal. Non-relevant indications can appear at section changes or where two metals meet, and the technician has to judge them correctly.

When the question is wall loss or buried weld flaws, ultrasonic testing is the right tool; the Mobile UT page covers that.

Codes and acceptance criteria for MT in Mobile

The governing code names the technique and the rejection limits. ASME Section V, Article 7 gives the requirements for the magnetic particle method, and ASTM E709 and E1444 are the reference guide and practice. ASME B31.3 requires magnetic particle examination under paragraph 344.3 with acceptance in Table 341.3.2, and ASME Section VIII Division 1 uses Mandatory Appendix 6 for MT methods and acceptance on pressure vessels.

Structural welds and many shipyard fabrications are checked to AWS D1.1, which describes magnetic particle examination of welds and lists the surface discontinuity limits. Many shipbuilding specifications add their own contract requirements, so your drawings and specification package control the job. In-service pressure equipment under API 510, API 570 or API 653 stays under the owner's authorized inspector, and Atlantis supplies the examination findings for that person.

The Alabama Department of Workforce administers the state boiler and pressure vessel program under the Alabama Boiler and Pressure Vessel Safety Act, which calls for regular inspections and operating certificates on covered equipment. When a repair has been made to a covered vessel, MT records of the repaired weld area can form part of the owner's file. Confirm with your inspector which repairs need documentation before work starts.

How magnetic particle inspection is done

Field work is usually done with an electromagnetic yoke, which lets the technician magnetize a small region at a time, or with prods for heavier sections where AC contact current is permitted. ASME Section V sets a minimum lifting force for yokes, so the yoke is checked against a test weight at the maximum pole spacing before use. Each area is examined with the field in two roughly perpendicular directions, so cracks in any orientation are caught.

Particles may be dry powder, which suits rough welds and heated surfaces, or a wet suspension. Wet fluorescent particles are more sensitive and are examined under ultraviolet light in a darkened area, with the light intensity checked before examining. Where a contrast paint background is applied, visible particles in a contrasting color are used under white light. Field indicators, such as a pie gauge or a shim, confirm that the field strength is adequate for the particular surface and technique.

After examination, indications are marked, photographed when needed, and compared with the acceptance table. If residual magnetism could affect later welding, machining or an instrument, the part is demagnetized and checked with a gauss meter. Surfaces are then cleaned of particles. Heavy mill scale and slag on welds must be removed first, because a crack hidden under slag will not produce a clear indication.

Surface condition and typical indications on Mobile steel

Weld toe cracks, lack of sidewall fusion that reaches the surface, arc strikes, laps and grinding cracks are the indications most often found on shipyard and structural steel. Heat-affected zones that have been rapidly cooled can develop hydrogen cracks, which sometimes appear hours or days after welding, so a hold period before examination may be written into the procedure. Cyclic loading at the dock produces fatigue cracks that start at notches and often grow in a direction that the two-direction technique is designed to catch.

Coastal air and splash zones leave salt, rust and marine growth on steel. Preparation is usually by wire brushing, grinding or light blasting until the metal is clean and dry enough for the particles to move freely. Oil and grease are removed with a solvent, because they cause particles to clump and give false patterns. Rough weld profiles can trap particles, so the technician looks at whether an indication is relevant, caused by geometry, or a true discontinuity before it is recorded. Where doubt remains, the area is cleaned, re-magnetized and re-examined, and a second method may be used to confirm.

Qualification and review

MT is performed by Atlantis technicians qualified under the company written practice, which follows ASNT SNT-TC-1A. The Level II technician performs the examination, interprets the indications and records them. An ASNT Level III approves the technique sheet and signs off on the report. Anoop Rayavarapu is the company's Level III, qualified in UT, RT, MT, PT and VT.

Mobile has no Atlantis premises. Crews are mobilized to your shipyard, plant or fabrication shop for the agreed scope, and the work is organized around your site access rather than a standing presence nearby. Under SNT-TC-1A each employer certifies its own personnel, so any technician you employ directly is certified by your company. Procedure help and written practice work are offered through our written practice development service.

What the MT report includes

A magnetic particle report identifies the component, location, drawing number and the governing code. It records the technique used, whether yoke or prods, the particle type and color, the lighting levels and the field direction. Equipment details such as the yoke's serial number and the date of its last lifting-force check are listed, along with the technician's name and level.

Every indication is described by location, length and orientation, and the report states whether it is accepted or rejected against the named criteria. A sketch or a photograph shows where each indication lies. If a weld was dressed and re-examined after a repair, both results appear so the record shows what was found and what was removed. Level III review is recorded on the document before it reaches you.

Planning an MT job in Mobile

Hot Gulf Coast summers raise steel temperatures well above comfortable levels, and wet particle suspensions behave differently on hot metal, so dry particles or a heat-tolerant technique may be specified. In the cool season, cold steel is rarely a problem in Mobile, though occasional freezes require the part and materials to be within the procedure's temperature range. Humidity and sea air speed up rusting after cleaning, so surfaces are examined soon after preparation.

Fluorescent inspection needs darkness. Outdoors in daylight, that means a portable dark enclosure or a tent; inside a hull block or a vessel, it is easier. Plan for lighting, power for the yoke and a place to stage equipment. Shipyards and port terminals typically require safety orientation and badging before crews enter, and plants require hot-work or confined-space permits when examining inside vessels. Hurricane season can interrupt work near the water, so leave scheduling room.

When the work is on a ship, our readings and findings are for the owner's own decisions. Atlantis is still in the process of obtaining class approval (UR Z17, with DNV, Lloyd's Register and ABS) for ship thickness measurement, and class-credited surveys require firms approved by the vessel's society.

MT, PT or UT in Mobile

For carbon steel welds that need a fast check for surface cracks, magnetic particle inspection is usually the first choice because it is quick, sensitive and shows the flaw directly on the surface. If the part is stainless steel, aluminum or a non-ferrous alloy, use liquid penetrant testing. If you need to know whether a flaw extends below the surface or how much metal remains, use ultrasonic testing.

The MT versus PT comparison goes into more detail. For work covering all of Alabama, see the Alabama inspection services page. A few jobs benefit from combining methods, for example PT on a stainless pipe weld and MT on its carbon steel support attachments in the same shutdown.

Training MT technicians in your company

Companies that want their own people qualified start with formal instruction, then practical hours on real parts, under their written practice. We provide MT Level 1 training and MT Level 2 training, and the Mobile training page explains how courses reach local employers. The complete MT guide is a good starting read for new technicians, and the practice tests help check progress.

Frequently asked questions

Which materials can magnetic particle inspection be used on in Mobile?

MT works only on ferromagnetic materials such as carbon and low-alloy steel. Austenitic stainless steel, aluminum and copper alloys are not magnetic, so those parts are examined with liquid penetrant testing instead.

What can MT find on a crane or heavy lifting structure?

It finds surface and slightly subsurface cracks, most often fatigue cracks at weld toes, pins, pedestals and changes of section. It is not suited to measuring remaining wall thickness, which is a job for ultrasonic testing.

Is fluorescent or visible particle testing used on Mobile jobs?

Both are used. Fluorescent wet particles give higher sensitivity but need a dark area and ultraviolet light. Visible dry or wet particles with contrast paint work better outdoors or on rough welds. Your code and procedure decide.

Which codes govern magnetic particle inspection of welds?

ASME Section V Article 7 gives the method, with acceptance from the construction code, for example ASME B31.3 Table 341.3.2, Section VIII Division 1 Appendix 6 or AWS D1.1. Your engineer or specification names the one that applies.

Does Atlantis perform magnetic particle testing on ships?

Atlantis can examine welds and structures on a vessel for the owner's own decisions. It is still obtaining class approval, so examinations that must be credited to a class survey need a firm approved by that society.

Is an Atlantis crew stationed in Mobile?

No. Atlantis has no office in Mobile. Technicians are mobilized to your site for the agreed scope, and we coordinate site access, orientation and safety paperwork with you ahead of the job.

Why is demagnetizing needed after MT?

Residual magnetism can pull steel chips to a surface, disturb arc direction during welding, or interfere with instruments and machining. When it could matter, the part is demagnetized and checked with a field meter before it is released.

Can MT be done on painted steel in Mobile?

Thin, tight coatings may be acceptable if the procedure has shown that indications still form, but thick or flaking paint lowers sensitivity. The coating is often removed at the examination area, and the report notes what was done.

What should I send to get an MT quote for a Mobile site?

Send the component list or drawings, the governing code, surface condition, access notes, temperature, and any site orientation requirements. With that we can define the technique and the scope for the quotation.

Inspection and training around Mobile

MT by industry for Mobile: Offshore · Marine & Shipbuilding · Pulp & Paper.

MT by job: Magnetic particle weld inspection · Magnetic particle inspection of lifting equipment · Magnetic particle inspection of castings and forgings · Magnetic particle inspection of structural steel and bridges.

Training your own technicians: MT Level 1 training · MT Level 2 training · NDT training for Mobile technicians.

Request an MT inspection quote for Mobile

Send the component and material, the quantity, the code or specification and the site address. We reply within one business day with the scope, the mobilization plan and a quote. Request a quote for magnetic particle inspection in Mobile.

Need magnetic particle testing (MT) done, or learned?

Atlantis provides magnetic particle testing (MT) as an inspection service, trains technicians in it, and lets teams practise it on the Practical NDT simulator.