Ultrasonic Testing (UT) Inspection in Mobile, Alabama
Atlantis NDT mobilizes Level II ultrasonic technicians to sites in Mobile, Alabama for thickness surveys on piping, vessels and tanks, and for angle-beam examination of welds in structural and pressure steel. The work covers shipyard and fabrication steel, chemical and paper-mill piping, port equipment and storage tanks. Send us the asset list, drawings and the code your owner or inspector works to, and request a UT inspection quote for Mobile.
Where ultrasonic inspection earns its keep in Mobile
Mobile is Alabama's only seaport, and its industry is built around the water. Steel and aluminum ships are built and repaired on the river, bulk and container cargo moves across the docks, and chemical, paper and steel producers sit along the corridor that feeds the port. Each of those settings leaves steel that thins, cracks or hides weld defects, and ultrasonic testing is the usual way to measure it from one side without cutting anything open.
On the industrial side the typical targets are carbon steel process piping carrying caustic, acid, brine or hydrocarbon service; heat exchanger shells; pressure vessels and surge drums; and atmospheric storage tanks. Paper and wood-products mills add steam piping, digester and boiler components, and long runs of condensate line where erosion and under-insulation corrosion are routine. Along the waterfront, UT thickness readings are taken on sheet pile and bulkhead steel, crane runway girders, and the legs and pins of heavy lifting equipment.
Fabrication shops serving the shipbuilding and offshore trades need weld examination more than corrosion mapping. A shop building structural modules or pressure skids may be asked to prove that groove welds are free of lack of fusion before paint, and that is where shear-wave work comes in. Our national ultrasonic testing service page describes the general scope; this page covers how it applies in Mobile.
What UT measures, and what it cannot see
A contact transducer sends a short pulse of sound into the steel and the instrument displays the returning echoes against time. For thickness, the time between the front surface and the back-wall echo, multiplied by the sound velocity for that material, gives wall thickness. For welds, an angled shear wave travels through the fusion zone and reflects from planar flaws such as lack of fusion, cracks and incomplete penetration, which show on the screen as echoes between the entry point and the back wall.
The method has real limits that matter on Gulf Coast steel. Heavy scale, flaking paint and rough corrosion pits scatter sound and can hide a loss of wall or give a false reading, so surface preparation is part of the job. Thick coatings on ship plating and tank shells can be measured through only when the procedure has been proven on a matching sample. Cast and coarse-grained material, such as some austenitic stainless weld metal, attenuates the beam and may need a different technique or a different method altogether. Laminations in plate can sit directly under a weld and block the beam, so scanning for them before weld work is routine on thick plate.
Ultrasonic testing also does not tell you the cause of a flaw. A reflector is sized, located and compared with the acceptance rules; an engineer or the owner's authorized inspector decides what happens next. Where a surface-breaking crack is suspected, an MT or PT check from our magnetic particle and penetrant pages is often the quick confirmation.
Codes and acceptance criteria used for Mobile work
The code decides how the examination is done and what is rejected. For shop and field welds in process piping, ASME B31.3 sets the examination extent and the acceptance criteria in Table 341.3.2, and ultrasonic technique follows ASME Section V, Article 4 for welds and Article 5 for materials. Pressure vessel welds built to ASME Section VIII Division 1 use Mandatory Appendix 12 for ultrasonic examination of welds. Structural steel work follows AWS D1.1, which has its own ultrasonic acceptance rules for groove welds, and ASTM E164 and E114 cover the contact technique and equipment checks.
Thickness readings are governed by ASME Section V Article 5 and by ASTM E797, the practice for contact pulse-echo thickness measurement. In-service inspection of vessels, piping and tanks falls under API 510, API 570 and API 653, where the owner's authorized inspector is responsible for the inspection program. Atlantis performs the ultrasonic work and reports the data, such as thickness at each condition monitoring location, and does not act as that authorized inspector.
Alabama also regulates pressure equipment. The Alabama Department of Workforce runs the boiler and pressure vessel inspection program under the Alabama Boiler and Pressure Vessel Safety Act, with regular inspections and operating certificates for equipment that the act covers. Our thickness records can support the owner's inspector when a vessel is due. Owners should confirm which of their equipment is covered and who holds the commission for it.
How the ultrasonic work is performed
For corrosion and erosion surveys, the technician lays out a grid or a set of condition monitoring locations, marks them so the same spots can be read next time, and cleans each point down to bright metal. A dual-element probe is the normal choice on corroded surfaces because its separate transmit and receive crystals handle rough back walls better than a single-element probe. The instrument is calibrated on a step block of the same alloy before the work, rechecked during it, and verified again at the end.
A-scan display is used rather than reading a bare number off a digital gauge. Watching the waveform lets the technician see a doubled echo on thin wall, a laminar reflector or a pitted back wall that a numeric readout would misreport. Hot surfaces need a high-temperature probe and couplant, and the reading is corrected for the temperature effect on velocity. On insulated lines, the insulation is stripped at the test points by the owner's crew and replaced afterward.
For weld examination, angle-beam probes in the 45, 60 and 70 degree range are chosen for the joint geometry and wall thickness. A reference level is built from the code's calibration block, usually with side-drilled holes, and the weld is scanned from both sides where access allows, with the weld crown ground flush or the scan surface prepared beside it. Indications above the recording threshold are located, measured in length and compared with the acceptance table. A short sketch of each rejectable indication goes into the report.
Who performs and reviews the work
Atlantis technicians are qualified under the company written practice, which follows ASNT SNT-TC-1A. A Level II technician sets up and calibrates the instrument, performs the examination and interprets the results against the code. The written procedure is approved, and each report reviewed, by an ASNT Level III before it reaches you. Reports are reviewed by Anoop Rayavarapu, who holds ASNT NDT Level III in UT, RT, MT, PT and VT.
Atlantis has no office in Mobile. Technicians are mobilized to your site for the agreed scope, and we plan the visit around your access dates rather than a standing local presence. Certification of any individual belongs to the employer under SNT-TC-1A, so your own contractor's technicians hold their own employer's certificate. If you want procedures or a written practice reviewed before a job starts, the Level III consulting page explains that service.
Atlantis is certified to ISO 9001 and ISO 14001, and that covers how the company controls documents, equipment and records. The qualification of individual technicians remains a separate matter handled under the written practice.
What an ultrasonic report from Atlantis contains
Each report identifies the component, line number or tank, drawing reference and the code that governs the job. It lists the procedure and revision used, the instrument, probes and calibration blocks with their serial numbers, the couplant and the calibration checks. The technician's name and certification level appear on every sheet, and the Level III review is recorded.
For thickness work you receive a thickness grid or a table by condition monitoring location, with the nominal wall, the minimum required wall if the owner provides it, the readings and the date. Locations that fall below the owner's limit are flagged for the engineer. For welds, the report lists each recordable indication by position along the weld, depth, length and amplitude, and states accept or reject against the named criteria. Photographs and sketches of the scan setup are included where useful, so a later crew can repeat the examination in the same way.
Planning a UT job in Mobile
Mobile summers are hot and humid, and steel left in the sun can be too hot to touch. That affects couplant choice, probe wear and how long a technician can work in the field before a break. Winters are mild but occasionally reach freezing, and thickness readings on cold steel need the calibration block at the same temperature as the part. Hurricane season, from June through November, can close ports and shipyards with little notice, so schedules near the water carry some weather contingency.
Shipyard and port work usually involves badging, safety orientation, hot-work and confined-space rules, and sometimes escort requirements. Send those details early. Chemical and paper plants have their own turnaround windows, and the right time to read thickness on a line is while it is empty and accessible for cleaning. Highway and rail access into the Mobile area is good, which keeps mobilization simple for visiting crews, and we confirm lodging and the start date once the scope is agreed.
A note on ships: thickness readings on vessel plating taken by Atlantis are for the owner's own maintenance decisions. Atlantis is in the process of obtaining UR Z17 approval from DNV, Lloyd's Register and ABS for thickness measurement and holds no class approval yet. Gauging that has to be credited to a class survey must be done by a firm approved by that vessel's classification society.
UT, MT or PT for your Mobile job
Choose ultrasonic testing when the question is how much steel remains or whether a weld is sound all the way through. Choose magnetic particle inspection when you need to find surface and near-surface cracks on carbon steel, such as at the toe of a fillet weld on a crane pedestal, since MT is fast and sensitive there. Choose liquid penetrant testing for surface-breaking flaws on stainless steel, aluminum hull plate or nickel alloys, where magnetic methods do not work.
Many jobs use two methods together. A pressure vessel weld repair, for example, may need PT on the ground-out cavity, UT on the finished weld and a final thickness check. The three Mobile pages, together with the Alabama inspection services page, show how the methods split. The ultrasonic testing guide gives more background on probe selection and calibration.
Training your own UT technicians
If your company wants its own staff qualified, the route starts with training hours and documented experience under your written practice. We offer UT Level 1 training and UT Level 2 training, with theory delivered online and hands-on practice at your facility. The ultrasonic testing simulator lets trainees practice scanning before they touch real equipment. Our Mobile training page explains how courses are delivered for local employers, and the SNT-TC-1A eligibility checker shows the hours required for each level.
Frequently asked questions
What does ultrasonic thickness testing cost to arrange in Mobile, Alabama?
The effort depends on how many condition monitoring locations you have, the access and surface preparation needed, and the travel for the crew. Send the asset list and drawings through the quote link and we will scope the job against your code and inspector.
Can ultrasonic testing be done on painted or coated steel in Mobile?
Often yes, but the coating must be sound and the procedure proven on a sample with the same coating. Loose paint, scale and heavy fouling are removed first, because they scatter sound and can hide real wall loss.
Does Atlantis inspect ship hulls in Mobile with UT?
Atlantis can take ultrasonic thickness readings on vessel plating for the owner's own maintenance decisions. It is still obtaining class approval for thickness measurement, so readings that must be credited to a class survey need a class-approved firm.
Which code governs UT weld inspection on pressure piping near Mobile?
Process piping is normally examined to ASME B31.3 with technique from ASME Section V Article 4. Pressure vessels use ASME Section VIII Division 1, Appendix 12, and structural steel uses AWS D1.1. Your engineer names the governing code.
Do you replace the owner's API authorized inspector?
No. Under API 510, API 570 and API 653 the owner's authorized inspector remains responsible for the inspection program. Atlantis performs the ultrasonic examination and supplies the thickness and indication data for that inspector to evaluate.
How are Atlantis technicians qualified for UT?
Technicians are qualified under the company written practice, which follows ASNT SNT-TC-1A. A Level II performs and interprets the examination, and an ASNT Level III approves the procedure and reviews the report before it is issued.
Is there an Atlantis crew stationed in Mobile?
No. Atlantis has no office in Mobile. Technicians travel to your site for the agreed scope, and we coordinate access dates, badging and safety orientation with your plant or yard before mobilizing.
Can ultrasonic testing find surface cracks on a weld?
UT can detect cracks that reflect the beam, but surface-breaking cracks near the toe are usually confirmed faster with magnetic particle testing on carbon steel or penetrant testing on non-magnetic metals, so many welds receive both.
How should I prepare a line or vessel for UT in Mobile?
Make the test points accessible, remove insulation at those spots, clean each location to bright metal, and tell us the operating temperature. Hot lines need high-temperature probes and couplant, and sometimes a shutdown.
Inspection and training around Mobile
- Magnetic particle inspection (MT) in Mobile
- Liquid penetrant testing (PT) in Mobile
- Ultrasonic inspection services
- NDT inspection services in Alabama
UT by industry for Mobile: Offshore · Marine & Shipbuilding · Pulp & Paper.
UT by job: Ultrasonic pipe thickness testing · Ultrasonic weld inspection · Ultrasonic boiler tube thickness testing · Ultrasonic testing of castings and forgings.
Training your own technicians: UT Level 1 training · UT Level 2 training · NDT training for Mobile technicians.
Request an UT inspection quote for Mobile
Send the component and material, the quantity, the code or specification and the site address. We reply within one business day with the scope, the mobilization plan and a quote. Request a quote for ultrasonic testing in Mobile.
Need ultrasonic testing (UT) done, or learned?
Atlantis provides ultrasonic testing (UT) as an inspection service, trains technicians in it, and lets teams practise it on the Practical NDT simulator.