Ultrasonic Testing (UT) and Thickness Gauging in Chicago, Illinois

Atlantis NDT mobilizes ultrasonic testing technicians to Chicago plants, mills, rail yards and fabrication shops for wall-thickness surveys, corrosion checks and shear-wave examination of welds. Send us the equipment list, the code you work to and the access conditions, and we will scope the job around them. Request a UT quote for your Chicago site and we reply within one business day.

Where ultrasonic testing is used in Chicago

Chicago sits where Lake Michigan meets the busiest rail interchange in North America, and that mix drives the UT work around the city. On the Indiana lakeshore, minutes from the Illinois line, the Whiting refinery processes more than 400,000 barrels of crude a day, and refineries at Joliet and Lemont sit southwest of the city along the Des Plaines and Chicago Sanitary and Ship Canal corridor. Process piping, columns, drums and exchangers at plants like these lose wall slowly through corrosion and erosion, and ultrasonic thickness readings are how an owner tracks that loss from one campaign to the next.

Away from the refineries, the same instrument is used on a very different mix of steel. Integrated mills along the southern lakeshore run furnace shells, gas mains, cooling circuits and crane rails. Rail shops and bridge owners deal with fatigue-prone steel that has been in service for decades. Chicago also has 37 movable bridges inside the city limits, mostly the trunnion bascule design, and each of them carries steel girders, floor beams and machinery supports that need periodic examination. Warehouses, distribution centers and commercial towers add structural steel and crane runways to the list.

What ultrasonic testing finds, and what it misses

Ultrasonic testing sends a short sound pulse into the metal and times the echo. For a thickness job that echo comes from the back wall, so the instrument reports the remaining wall directly. For a weld job it comes from reflectors inside the weld: lack of fusion, cracks, slag lines and porosity that sit below the surface where visual and surface methods cannot see them. That is why UT is the usual volumetric method when a code allows it and radiography is not practical.

It has limits that matter on Chicago steel. Sound needs a smooth enough surface and a liquid couplant, so heavy scale, flaking paint and rough weld caps have to be dressed first. Pitted walls scatter the beam and can make a thickness reading jump, which is why the technician watches the A-scan trace rather than trusting a bare number. Coarse-grained castings and some cladding attenuate sound badly. And a thickness reading describes the spot under the probe, not the ten square feet around it, so the spacing of the readings is part of the procedure. When the question is a surface-breaking crack on a ferromagnetic part, magnetic particle or penetrant testing answers it better, and we say so rather than sell UT where it does not fit.

Codes, acceptance criteria and Illinois rules

For most Chicago refinery and plant work the governing documents are the owner's inspection program and the construction code. ASME Section V Article 4 covers ultrasonic examination of welds and Article 5 covers materials, while ASTM E797 governs contact pulse-echo thickness measurement. Acceptance of weld indications comes from the code that built the item: ASME Section VIII Division 1 Appendix 12 for vessels, ASME B31.3 for process piping, AWS D1.1 for structural steel, and AWS D1.5 where the owner is a bridge authority. In-service equipment follows API 510 for vessels, API 570 for piping and API 653 for tanks. In each case the owner's authorized inspector stays responsible for the inspection; Atlantis performs the ultrasonic work and reports the data that inspector needs.

Illinois adds its own layer. The Division of Boiler and Pressure Vessel Safety at the Office of the State Fire Marshal requires internal inspection of high pressure boilers every year, low pressure boilers every two years and pressure vessels every three years, and it does not allow non-code boilers or pressure vessels to be installed. Inside the city limits the City of Chicago Boiler Inspection Bureau, part of the Department of Buildings, inspects boilers and unfired pressure vessels itself. Thickness data on a registered vessel often ends up in front of one of those inspectors, so readings are recorded against fixed locations they can find again. The state and city pages are worth reading before you plan a campaign: Illinois boiler and pressure vessel FAQs and the Chicago boiler inspection page. Across the border in Indiana the state's own boiler program applies, so a Whiting-area job follows Indiana rules rather than Illinois ones. Process safety management under OSHA 29 CFR 1910.119(j) adds the requirement that inspection follow recognized and generally accepted good engineering practice, which is how most owners justify a written thickness program.

How thickness gauging is done

Corroded steel is gauged with a dual-element probe, which separates transmit and receive crystals so the instrument can read pitted or thin wall that a single-element probe would misjudge. The technician calibrates on a step block made of the same material as the part, checks the zero and velocity, and verifies the setup again at the end of the shift. With an A-scan display the pulse shape is visible, so a doubled echo on thin wall or a laminar reflection can be spotted and rejected instead of logged as a false reading.

The readings go on a grid that matches your isometric or vessel drawing. Each condition monitoring location gets a permanent mark, and the same point is read every campaign, which turns a pile of numbers into a corrosion rate. Hot lines need high-temperature probes, a couplant rated for the surface, and a correction for the temperature of the wall, because sound travels more slowly in hot steel and an uncorrected reading comes out thick. Insulated lines mean someone has to open a window in the jacketing, and that request belongs in the plan before the crew arrives.

Shear-wave examination of welds

Weld examination uses an angle-beam probe, usually 45, 60 or 70 degrees, that sends shear waves through the weld volume from the side of the joint. The technician builds a reference level, often a distance-amplitude curve from side-drilled holes in a calibration block of matching thickness, then scans from both sides where access allows and evaluates each indication by amplitude, length and position. Planar flaws such as lack of fusion and cracks reflect strongly when the beam meets them squarely, which is why the scan plan and the weld geometry have to be worked out together.

The procedure, not the technician's judgment on the day, sets what is recorded and what is rejected. We write it to the governing code, an ASNT Level III approves it, and the indication log shows the reference level used so a second examiner could repeat the work. On a Chicago bridge repair or a mill structure, where the weld may be thick and the access awkward, that written scan plan is also what lets the owner's engineer accept the result.

Who does the work

Atlantis technicians are qualified under the company's written practice, built on ASNT SNT-TC-1A. A Level II technician sets up and calibrates the equipment, performs the examination and interprets the results. An ASNT Level III approves the procedures and reviews the reports; the Level III behind our UT work is Anoop Rayavarapu, ASNT NDT Level III in UT, RT, MT, PT and VT. Atlantis has no office in Chicago. Technicians are mobilized to your site for the agreed scope, so the crew you get is assembled for your job rather than pulled from a local pool, and we confirm travel and site orientation requirements when we quote. Atlantis is certified to ISO 9001 and ISO 14001. If your contract needs a specific scheme or a customer-specific qualification, tell us at the start so we can confirm what is realistic.

What the UT report contains

A useful ultrasonic report lets someone repeat the job. Ours identifies the component and its location, the procedure and revision, the instrument, probe and calibration block, the couplant and surface condition, and the technician's name and level. Thickness work includes the grid with every reading, the nominal and minimum required thickness where you supply them, and flags for readings below the limit. Weld work includes a sketch showing each indication with position, length and amplitude against the reference level, plus an accept or reject call against the acceptance criteria you named. An ASNT Level III reviews the report before it goes to you. If your inspector needs the data in a particular layout for an API 510 or API 570 program, say so when you request the quote.

Planning a UT job in Chicago

Weather and access shape most Chicago jobs. Winter work outdoors means cold steel, frozen couplant and gloved hands trying to hold a probe steady; couplant rated for low temperature and a warm-up plan for the instrument save time. Lake wind off the water makes scaffold and ladder work harder on the lakeshore sites. Summer brings heat and humidity that affect both people and hot-surface readings. Refinery and mill outages are scheduled well in advance, so the right time to talk is before the work scope is frozen, not after the shutdown starts. Plants in the Calumet region and the Joliet corridor run badge and safety orientation processes that take time to clear, and Chicago bridge and rail work often requires track or lane access that has to be booked through the owner. Tell us about those steps early and we will build them into the schedule instead of discovering them at the gate.

UT, MT or PT for your Chicago job

Choose the method by the question you are asking. If it is how much wall is left on a pipe or tank shell, or whether a weld has internal flaws, ultrasonic testing is the tool. If you need to find a surface crack at a fillet weld or a lifting lug on carbon steel, magnetic particle testing in Chicago is faster and more sensitive at the surface. If the part is stainless, aluminum or any non-magnetic material, penetrant testing in Chicago is the way to find open cracks. Many scopes use two methods together, for example UT for thickness and MT on the repair welds. Our national ultrasonic testing page explains the service in general terms, and the ultrasonic testing guide goes deeper on the physics. For standards detail, see the explainer on ultrasonic thickness measurement requirements.

Training your own ultrasonic technicians

Some Chicago employers would rather build their own bench than hire it in. Atlantis trains technicians in ultrasonic testing through UT Level 1 training and UT Level 2 training, delivered as online theory with a practical examination at your facility, and your own written practice defines what qualifies a person under SNT-TC-1A. The Practical NDT ultrasonic simulator gives trainees scanning practice before they touch real steel. If you are setting up a group, read about NDT training in Chicago, check SNT-TC-1A eligibility and try the practice tests. For a written practice or Level III oversight, see outsourced Level III consulting. Statewide coverage is on our Illinois inspection services page.

Frequently asked questions

Does Atlantis have an office or lab in Chicago?

No. Atlantis has no office in Chicago. Technicians are mobilized to your site for the agreed scope, so the quote includes the travel and site orientation your plant requires. We confirm those details before work starts.

What can ultrasonic testing measure on a Chicago refinery pipe or vessel?

Remaining wall thickness at marked condition monitoring locations, plus internal flaws in welds. Readings are repeated at the same points each campaign so your inspector can calculate a corrosion rate and set the next interval.

Can UT find surface cracks?

Sometimes, but it is not the first choice. A surface crack on carbon steel is usually found faster with magnetic particle testing, and on stainless or aluminum with penetrant testing. We recommend the method that answers your question.

Which codes do you examine to?

The one governing your item: ASME Section V Articles 4 and 5 for technique, ASTM E797 for thickness, and the acceptance rules of Section VIII, B31.3, AWS D1.1 or D1.5. The owner or engineer names the code before work starts.

Do you perform API 510, 570 or 653 inspections?

No. Under those codes your authorized inspector is responsible for the inspection. Atlantis performs the ultrasonic work and gives that inspector the thickness and indication data in a form they can use.

Do Chicago boilers and pressure vessels have special rules?

Yes. Illinois sets inspection cycles through the State Fire Marshal, and inside the city limits the Chicago Boiler Inspection Bureau inspects boilers and unfired pressure vessels. We record readings against fixed locations so those inspectors can use the data.

What do I need to send for a quote?

The equipment list or drawings, the code or specification, the material and approximate thickness, the surface and insulation condition, the dates of any outage, and any site badging steps. The more detail you send, the tighter the scope.

Who certifies your technicians?

Technicians are qualified under the Atlantis written practice based on ASNT SNT-TC-1A, which is how the employer certifies its own personnel. An ASNT Level III approves procedures and reviews reports, and we can show the qualification record on request.

Inspection and training around Chicago

UT by industry for Chicago: Petrochemical · Power Generation · Fabrication & Welding · Steel & Primary Metals · Rail · Food, Beverage & Pharmaceutical.

UT by job: Ultrasonic pipe thickness testing · Ultrasonic weld inspection · Ultrasonic boiler tube thickness testing · Ultrasonic testing of castings and forgings.

Training your own technicians: UT Level 1 training · UT Level 2 training · NDT training for Chicago technicians.

Request an UT inspection quote for Chicago

Send the component and material, the quantity, the code or specification and the site address. We reply within one business day with the scope, the mobilization plan and a quote. Request a quote for ultrasonic testing in Chicago.

Need ultrasonic testing (UT) done, or learned?

Atlantis provides ultrasonic testing (UT) as an inspection service, trains technicians in it, and lets teams practise it on the Practical NDT simulator.