Practical NDT Simulator in Martinez, California
Martinez is the Contra Costa County seat, a small waterfront city on the Carquinez Strait with two large refining sites on its edges. A few miles west sit the Rodeo and Richmond plants; across the water are Benicia and the Solano County shore. For NDT technicians, this stretch of shoreline is one long, continuous job site: process units, tank farms, hydrogen plants, marine wharves and the turnarounds that bring hundreds of contract workers through the gates. Practical NDT, built by Atlantis NDT, is an online simulator where those technicians can rehearse the work. It opens realistic 3D jobs on virtual piping, vessels, exchangers, tanks and welds, and the trainee works each job with virtual instruments from set-up to report.
Twelve method families are covered. The ultrasonic group is conventional UT (thickness gauging, straight beam, angle beam), PAUT and TOFD. RT is practiced with film, CR and DDA images. MT runs on AC and DC yokes; PT on visible and fluorescent penetrants; VT through direct viewing, borescopes and drones; ET with absolute and differential coils, bobbin probes for tubes and bolt-hole probes. Then the refinery specialties: IRIS for exchanger tubes, MFL floor scanning for tanks, guided-wave screening along pipe, and positive material identification with XRF, which matters a great deal in California refineries. The library runs to 473 jobs and 33 lessons across 12 workplaces. Contractors and plant teams along the strait can request a Martinez demo.
The industrial shoreline around Martinez
Martinez Refining Company. PBF Energy owns the refinery that adjoins the city, which Shell operated for decades before selling it. It is a large, complex fuel refinery with crude units, cokers, hydroprocessing, sulfur recovery and extensive tankage, and an Air Products hydrogen plant sits within the site.
Martinez Renewable Fuels. The former Marathon refinery, a short drive along the shoreline, has been converted to produce renewable diesel and related fuels from fats and vegetable oils, under a joint venture between Marathon and Neste. Another Air Products hydrogen plant serves it.
Rodeo. Phillips 66 converted its Rodeo refinery to renewable fuels, and Air Liquide runs a hydrogen plant there. The pipelines, tanks and marine facilities tied to both sites remain part of the local inspection picture.
Richmond. Chevron's Richmond refinery, on the bay side of the county, is one of the largest on the West Coast and draws heavily on the same pool of inspectors and contractors.
Marine terminals. Crude, feedstocks and products move across wharves on the strait. California's Marine Oil Terminal Engineering and Maintenance Standards, known as MOTEMS, set requirements for audits and inspection of those terminals, and the steel piping and structures on the wharves see a harsh marine atmosphere.
East along the river. Gas-fired power plants and other industry at Pittsburg and Antioch, plus pipelines and pump stations running toward the Central Valley, round out the regional workload. The Stockton page and the Sacramento page cover the inland side.
The rules that shape inspection in Contra Costa County
Few places in the United States regulate refinery safety as closely as this county. Three layers matter to anyone doing NDT here.
Cal/OSHA's refinery process safety rule. Since 2017, California refineries have operated under Title 8, section 5189.1, a refinery-specific process safety management regulation. Among other things it requires damage mechanism reviews, which identify how each process unit can degrade, and a hierarchy-of-hazard-controls analysis. Inspection data is the evidence those reviews depend on, so thickness surveys, crack detection and alloy verification feed directly into the plant's safety program.
The County Industrial Safety Ordinance. Contra Costa County's ordinance, Chapter 450-8, expands the state's accidental release prevention program for refineries and chemical plants in unincorporated areas. Contra Costa Health lists Martinez Refining Company, Martinez Renewable Fuels, the Phillips 66 Rodeo refinery, the Air Liquide Rodeo hydrogen plant and the two Air Products plants as covered facilities. Covered sites must investigate major chemical accidents or releases with root cause analysis. The City of Richmond has an identical ordinance that covers the Chevron refinery.
Workforce requirements. California law also requires refinery contractors working in apprenticeable building-trades occupations to use a skilled and trained workforce. Whether that touches a particular inspection crew depends on the scope, so confirm it with the refinery before mobilizing.
Underneath all of that sit the industry codes most refinery inspection programs use: API 510 for pressure vessels, API 570 for piping, API 653 for tanks, API RP 571 for damage mechanisms and API RP 578 for alloy verification. The simulator does not teach those codes, and Atlantis does not train for API certifications; the point is that a technician working here should expect every reading to end up in a program that regulators audit.
What renewable conversions change for inspectors
Two of the four big sites in this corner of the county now run on renewable feedstocks. Fats and vegetable oils bring organic acids, chlorides, phosphorus and water into units that were designed for crude-derived streams, and hydroprocessing them produces water and carbon oxides in quantities the old units did not see. The result is corrosion and fouling in places where inspection history is thin. Plants respond with new monitoring locations, more thickness readings, attention to welds in revamped piping, and alloy checks wherever materials were changed. Technicians who learned the old corrosion patterns need to approach these units with fresh eyes, and practice on thickness grids, weld volume and alloy identification is a sensible way to stay sharp.
Hydrogen plants add their own challenge. Reformer tubes operate at very high temperature and degrade by creep, and their inspection uses specialist techniques that are beyond the scope of the simulator. The surrounding piping, exchangers and vessels are ordinary process-plant work.
Simulator content that fits Martinez work
| Martinez-area job | What the inspector looks for | Methods to practice | Workplace |
|---|---|---|---|
| Piping circuit surveys | Wall loss at monitoring locations, corrosion under insulation follow-up | UT thickness, guided-wave screening, VT | Process plant |
| Turnaround weld work | Root and sidewall flaws in repair and new welds | PAUT, TOFD, RT interpretation, MT, PT | Welding workshop |
| Exchanger bundles | Tube thinning, pitting, cracking | ET bobbin, IRIS | Heat exchanger |
| Tank inspections | Floor pitting, shell and nozzle condition | MFL, UT thickness, VT | Storage tank |
| Alloy verification | Wrong materials in critical service | PMI by XRF | Process plant |
| Bench and shop work | Fittings, flanges, small components | PT, MT, UT | NDT lab |
Method pages: ultrasonic testing, phased array UT, TOFD, radiography, eddy current, magnetic particle, penetrant and visual. A free A-scan tool runs in the browser if you want a quick look first.
A twelve-step SOP like a refinery job package
Inspectors who work turnarounds on the strait live by job packages, permits and sign-offs. Practical NDT holds every practical to the same discipline: a fixed twelve-step standard operating procedure. It opens with a work order. Before setting up, the trainee confirms that the specimen, the material it is made from and the requested method are consistent with each other, the same habit that stops a technician from shooting the wrong circuit or gauging a line with the wrong velocity. Then the instrument is calibrated on the reference, the examination is carried out, and the data quality is reviewed before any result goes forward. The closing steps are a post-check of the equipment, a training report and a debrief.
Each job is tied to a specific revision of its procedure and equipment. That keeps everyone on the same version and makes it simple for a supervisor to compare two people's results.
Jobs run at three levels of assistance, so a helper on their first refinery contract can follow prompts while a seasoned Level II runs the same job with none. Credit is given only where the trainee recorded evidence of the step. Interpreting indications stays with the instructor, who reviews the trainee's calls; the software does not score them.
Three ways to run it
- Browser: open a job from a home computer, an office desktop or a phone, with no installation.
- PC or laptop, offline: download the application once and run it without a connection, handy in a contractor's trailer or where a refinery's network blocks outside sites.
- VR headset: a standalone headset runs the simulator through WebXR, tracked by hand or by controllers, for practicing probe handling, scan coverage and working around pipe racks and vessel nozzles.
How Martinez-area employers can use it
- Turnaround readiness. Big turnarounds on the strait pull in technicians from across the West. A short program of simulator jobs before arrival gets everyone back into thickness, weld-volume and tube-inspection routines.
- Waiting time during onboarding. Refinery safety orientation, badging and site-specific training can leave new hires idle for days. Simulator practice turns that time to use.
- Practice on renewable units. Teams assigned to converted units can rehearse surveys and alloy checks before they meet unfamiliar corrosion patterns.
- Rehearsal before practical exams. A job run with no assistance is laid out much like the practical exam a refinery contractor would set.
- Rare flaws. Practice on defects a contractor seldom has on a physical sample, from lack of fusion to tube cracking.
Training around the Bay Area
Bay Area inspection companies and refinery contractors mostly develop technicians in house, under their own written practices, with classroom work, on-the-job training and supervised experience. Atlantis provides SNT-TC-1A-based courses in which theory is completed online and the practical takes place at the employer's facility: see NDT training in Martinez and California, the Level 1 and Level 2 pages and Level III preparation. The free NDT practice tests help with written exams. Practical NDT sits alongside these as a place to practice, not a replacement for any of them.
SNT-TC-1A and the employer's role
Most contractors here certify NDT personnel under ASNT SNT-TC-1A. Certification is the employer's act: its written practice fixes, method by method and level by level, the classroom hours, the field hours, the exams and the eye tests a technician needs. The SNT-TC-1A eligibility checker shows the usual requirements. A simulator does not certify anyone, it does not replace the practical exam on real specimens, and its hours are not experience hours.
Where the simulator stops
Practical NDT trains people. It is not a validated engineering tool, and it plays no part in a damage mechanism review, a remaining-life judgment or an acceptance decision on real equipment. The radiography jobs use no radiation. In California, industrial radiography is licensed by the state's Department of Public Health and radiographers need state certification; Atlantis does not perform radiography in the United States.
Records in the Atlantis LMS and ERP
The simulator is part of the Atlantis LMS and ERP. A contractor's technicians reach it through the Atlantis client portal with one login, and their practice record joins the rest of their training file, which helps when a refinery asks to see qualification and training records. See the eLearning app.
Frequently asked questions
Can Martinez technicians use an NDT simulator for refinery technicians in Martinez?
Yes. Practical NDT includes process plant, heat exchanger and storage tank workplaces with thickness, weld, tube, floor and alloy jobs. It runs in a browser, offline on a PC or laptop, or on a VR headset.
Does it cover PMI for alloy verification?
Yes. XRF-based PMI is one of the twelve method families. It is practice in technique and documentation, not a substitute for the plant's own verification program.
Can it help with renewable diesel unit inspections?
It can help technicians practice the methods those units rely on, such as thickness surveys, weld examination and alloy checks. It does not model any specific plant.
Will simulator time count toward my SNT-TC-1A hours?
No. Experience hours come from real work under your employer's written practice.
Can we use it inside a refinery with restricted networks?
Yes. The downloadable PC version runs offline once installed.
Does Atlantis have staff stationed in Martinez?
No. Atlantis has offices in Houston and Hyderabad and supports California employers online and at their sites.
How do we arrange a demo?
Use the Martinez demo request. Tell us your methods and crew size; we reply within one business day.
Nearby pages: Practical NDT in the San Francisco Bay Area and California, plus the Practical NDT overview.
Part of practical NDT training in California and the wider practical NDT training programme at Atlantis NDT.
Every NDT method in one simulator
- All methods, one simulator: 12 method families: UT, PAUT, TOFD, RT, MT, PT, VT, ET, IRIS, MFL, guided-wave UT and PMI, across 473 jobs and 12 workplaces.
- Follows the SOP: Every job runs the same twelve-step procedure, from the work order and calibration to the post-check, the training report and the debrief, so trainees build one disciplined habit on every method.
- Browser, PC or VR: Runs in a browser, on a PC or laptop (offline once downloaded) and in VR on a standalone headset, and connects to the Atlantis LMS and ERP with one sign-in.
Each Practical NDT method and workplace has its own national page: what you practise, what the simulator computes and what it cannot teach. Practical NDT is delivered online, so the same pages apply wherever your team works.
Methods: UT practical simulator · Phased array UT simulator · TOFD simulator · Radiography simulator · Magnetic particle simulator · Penetrant testing simulator · Visual testing simulator · Eddy current simulator
Workplaces: NDT lab · Welding workshop · Process plant · Storage tank · Heat exchanger · Aviation
Practise now: Free ultrasonic A-scan simulator
Speak to an ASNT NDT Level III
Discuss your inspection requirements with Atlantis NDT. Include the asset, method, location and documents you need reviewed.