Magnetic Particle Inspection (MT) in San Antonio, Texas

Atlantis NDT sends Level II technicians to San Antonio plants, fabrication yards, hangars and rail sites to run magnetic particle inspection (MPI, also called mag particle testing) on carbon and low-alloy steel. We examine weld toes, lifting hardware, structural connections and pressure-equipment welds for surface and slightly subsurface cracks, and we report each finding against the acceptance criteria of your code. Describe the parts and the code through the quote request form and we reply within one business day.

Where magnetic particle inspection is used in San Antonio

The city's steel is varied. Automotive assembly and its supplier base use heavy press frames, fixtures, lifting beams and conveyor structure that fatigue at welds and bolted lugs. Aerospace repair and overhaul operations around the former Kelly Air Force Base need handling equipment, ground-support stands and hangar crane structure inspected for cracks at attachment welds. Energy fabricators serving South Texas build skid frames, separator vessels, lifting lugs and pipe supports, and the municipal power system has boiler casings, structural supports and rack piping.

Warehousing and logistics sites, including the railport at Port San Antonio, run overhead cranes, hoist hooks, spreader bars and forklift forks. These are the components where a fatigue crack is both likely and costly. MT is the usual method for them, since a crack at a fillet weld toe or at the root of a hook thread opens to the surface in ferromagnetic steel and shows clearly under magnetic particles. The same logic applies to tank shell-to-bottom welds at bulk storage terminals and to nozzle-to-shell welds on vessels.

How the method works, and where it stops

Magnetic particle testing magnetizes the part. A discontinuity that lies across the field lines distorts the field and leaks flux at the surface, and fine iron particles gather at the leak to form a visible line. That physics sets the limits. The part must be ferromagnetic: carbon steel and most low-alloy and martensitic steels qualify, while austenitic stainless steel, aluminum, copper and titanium do not. The method finds surface and slightly subsurface discontinuities, not deep internal flaws. A crack parallel to the field gives almost no signal, which is why a second examination with the field turned roughly ninety degrees is required.

When the part is stainless or non-magnetic, use penetrant testing in San Antonio. When the question is wall loss or an internal weld flaw, use ultrasonic testing in San Antonio.

Technique: yokes, prods, wet and dry particles

Most field work in San Antonio uses an electromagnetic yoke. ASME Section V, Article 7 requires an AC yoke to lift at least 10 pounds at the maximum pole spacing used, and a DC or permanent-magnet yoke at least 40 pounds, and the technician checks this with a calibrated test weight before use. The yoke legs sit on either side of the weld, the particles are applied while the field is on, and the area is then examined for indications. After that the yoke is rotated so a second pass at roughly right angles covers cracks in any direction.

Dry powder suits rough surfaces and warm parts in dusty outdoor settings; wet visible particles suit smoother surfaces and finer cracks; wet fluorescent particles give the highest sensitivity and are viewed under UV-A light in a darkened area, with the light intensity and ambient white light measured against the procedure limits. Prods can pass current through a part for large casting or weld areas, though we avoid them where arc burns on the surface are unacceptable. When residual magnetism would affect later welding, machining or service, the part is demagnetized and checked with a field meter. Our magnetic particle testing guide covers the method in plain terms, and the Article 7 explainer walks through the code text.

Codes and acceptance for San Antonio work

Which criteria apply depends on what the part is. ASME Section VIII Division 1 Appendix 6 sets MT methods and acceptance for pressure vessels, and ASME B31.3 paragraph 344.3 and Table 341.3.2 apply to process piping. Structural steel under AWS D1.1 and bridge steel under AWS D1.5 use their own visual and magnetic particle clauses, and ASTM E709 and E1444 are the guide and practice most written procedures follow. For in-service equipment under API 510, 570 or 653, the owner's authorized inspector decides on repair or continued service, and Atlantis provides the crack indications and their locations and sizes.

Texas regulates boilers under Chapter 755 of the Health and Safety Code through the Department of Licensing and Regulation. Repairs and alterations to boilers and pressure vessels follow the National Board Inspection Code, and the commissioned inspector signs off. The MT results we supply, for example at a weld repair on a header or a lug weld, become part of that record. Process safety management in OSHA 29 CFR 1910.119(j) expects equipment inspection under recognized good engineering practice, so cracks found by MT feed straight into your mechanical-integrity program.

Who performs the magnetic particle inspection

We have no office in San Antonio. Level II technicians mobilize to your site for the scope. They are qualified under the Atlantis written practice, built on ASNT SNT-TC-1A: Level II performs and interprets the examination, and an ASNT Level III approves procedures and reviews reports. Technical authority sits with the founder, Anoop Rayavarapu, ASNT NDT Level III in UT, RT, MT, PT and VT. Atlantis holds ISO 9001 and ISO 14001 certification for its management system. If your procedure already exists, we follow it; if it does not, Level III consulting can produce one to your code.

Reading indications: relevant, non-relevant and false

Finding a particle line is easy; deciding what it means is the skill. Relevant indications come from discontinuities such as cracks, laps and lack of fusion. Non-relevant indications come from magnetic writing, sharp section changes, the edge of a weld crown or the boundary between a weld and a heat-affected zone, where flux leaks without a flaw being present. False indications come from poor cleaning, particles trapped on rough surface or too much current. A Level II technician re-examines doubtful lines after light cleaning and re-magnetizing, and records how the call was made. A rounded indication on a hook thread and a straight line at a weld toe do not carry the same meaning, and the report says which one the technician saw.

In practice that means careful surface preparation before the yoke goes down. We remove loose scale and weld spatter with a wire brush or light grinding, keep the area free of oil, and treat painted steel according to the procedure, which sets a maximum coating thickness. Magnetic particle work on structure that has been painted and repainted for years often needs a patch cleaned to bare metal at each weld, and the owner should plan for the touch-up afterwards.

Typical San Antonio scopes

Most requests in the city fall into a handful of patterns. A plant wants periodic inspection of overhead crane hooks and runway welds as part of its rigging program. A fabricator needs final MT on structural welds before shipment to a project, to AWS D1.1 or the contract specification. A vessel repair crew needs MT on a ground-out crack repair before the weld is closed and again afterward. An operator of storage tanks wants MT on the shell-to-bottom weld or on a repaired nozzle during an internal inspection. A maintenance department wants a lifting-lug check before heavy equipment is moved. Each is sized by the number of welds or parts, the access, and the procedure, and each ends with a report your own inspector or engineer can file.

What the MT report contains

The report ties each result to its method. It names the component and its tag, the code and the procedure with revision, the equipment (yoke or bench, serial number, last lifting-power check), the particles and carrier, the field direction and number of passes, the light levels for fluorescent work, the surface condition and temperature, and the technician and level. Each indication is located on a sketch with its type, orientation and length, then marked relevant or non-relevant and accepted or rejected against the named acceptance criteria. If demagnetization was required, the residual field reading is recorded. Photographs support disputed calls without replacing the written finding.

Planning an MT job in San Antonio

Heat and dust drive local planning. In summer the surface of steel in direct sun can run well above the range at which wet particles and carriers work reliably; evaporation makes carriers dry before the pass is complete. We plan outdoor wet work for shaded or cooler periods, and we use dry powder where surface temperature rules out liquids. Wind complicates dry powder, so a screen or a shift of schedule may be required. A rare winter cold snap affects carriers less than summer heat does, but moisture on parts still ruins contrast.

For fluorescent work we need dark enough conditions; for hangar interiors and plant buildings that is often easy, while for outdoor structure a portable shroud or an after-dark window may be needed. Allow for site badging, safety orientation, and any hot work or confined space permits. Cranes and elevated structure need access equipment arranged in advance, since a yoke inspection of a hook block or runway beam is only as good as the reach. Tell us your outage dates and any access limits when you ask for the quote.

MT, PT or UT for your job in San Antonio

If the part is carbon steel and the fear is a crack at the surface, MT is typically the faster and more sensitive choice. If the part is stainless or non-ferrous, switch to penetrant. If you need to know how deep a crack runs or whether there is wall loss behind it, add ultrasonic sizing and thickness. See MT versus PT for the trade-offs, and the national page for magnetic particle testing services for scope.

Training your technicians in magnetic particle testing

For an in-house program, we offer MT Level 1 and MT Level 2 courses based on SNT-TC-1A recommended hours. Candidates can use NDT practice tests to check readiness, and your company certifies its own staff under its written practice. Explore San Antonio NDT training for how the courses are delivered, with the hands-on practical at your facility.

Frequently asked questions

Do you have an office in San Antonio for magnetic particle work?

No. Atlantis has no office in San Antonio. We mobilize Level II technicians to your site for the agreed scope and bring the yokes, particles, light meters and calibration weights needed for the job.

What materials can magnetic particle inspection test?

Only ferromagnetic material: carbon steel, most low-alloy steel and martensitic grades. Austenitic stainless steel, aluminum, copper and titanium are not magnetic and need liquid penetrant testing instead for surface-breaking flaws.

Why does the part get examined twice?

A crack lying parallel to the magnetic field gives almost no signal. ASME Section V Article 7 therefore calls for two examinations at roughly right angles so that cracks in any direction can be detected.

Can you inspect crane hooks and lifting hardware?

Yes. Hook shanks, thread roots, spreader bars, lugs and weld attachments are standard magnetic particle subjects, examined to your procedure and the rated-load program. The owner or rigging authority decides whether a cracked component returns to service.

When do you use wet fluorescent particles?

Fluorescent particles give the highest sensitivity and are used for fine cracks and critical welds. They need UV-A light and a darkened viewing area, and the light intensity and ambient light are checked against the procedure limits.

Is demagnetization always required?

No. It is done when residual magnetism could interfere with service, later welding or machining, or when the specification demands it. We record the residual field reading when demagnetization is performed.

Does Atlantis provide API inspectors for tanks and vessels?

No. For API 510, 570 and 653 work the owner's authorized inspector is the inspector of record. We perform the magnetic particle examination and deliver the indication data and records that inspector requires.

How do I request a magnetic particle inspection quote in San Antonio?

Use the quote form to send component types, material, code, surface condition, access and your shutdown window. We scope the examination, list assumptions and reply within one business day.

Inspection and training around San Antonio

MT by industry for San Antonio: Aviation & Aerospace · Oilfield & Drilling.

MT by job: Magnetic particle weld inspection · Magnetic particle inspection of lifting equipment · Magnetic particle inspection of castings and forgings · Magnetic particle inspection of structural steel and bridges.

Training your own technicians: MT Level 1 training · MT Level 2 training · NDT training for San Antonio technicians.

Request an MT inspection quote for San Antonio

Send the component and material, the quantity, the code or specification and the site address. We reply within one business day with the scope, the mobilization plan and a quote. Request a quote for magnetic particle inspection in San Antonio.

Need magnetic particle testing (MT) done, or learned?

Atlantis provides magnetic particle testing (MT) as an inspection service, trains technicians in it, and lets teams practise it on the Practical NDT simulator.