Magnetic Particle Inspection (MT) in Detroit, Michigan
Atlantis NDT provides magnetic particle inspection in Detroit and across Michigan for steel weldments, forgings, castings, press and tooling structures, lifting equipment and refinery steel. Technicians are mobilized to your plant, forge shop or job site with portable yokes, particles and UV-A lights, examine ferromagnetic parts to a written procedure and report each indication against the acceptance criteria you specify. Use the Detroit MT quote request and we reply within one business day.
Where magnetic particle inspection is used in Detroit
Detroit is where steel, forging and machining meet vehicles, and nearly every link in that chain gets magnetic particle work. Powertrain and chassis plants process crankshafts, camshafts, connecting rods, axle shafts, steering knuckles and gear blanks that are checked for cracks, seams and grinding burns. Forge shops and foundries around the metro area examine hot-forged and cast steel parts against customer drawings. The steel complexes along the Detroit and Rouge rivers, including the Zug Island blast furnaces and the Dearborn mill, rely on MT for roll necks, crane hooks, ladle hardware, couplings and structural welds in rolling and finishing lines.
Production benches inside the plants are usually owned and run by the manufacturer. The field work that people call on Atlantis for is different: press frames and die-set welds, robot fixture and tooling welds, building steel and crane runway repairs, lifting beams and hooks, rail car and truck frame repairs, and weld repairs after an outage. The refinery in southwest Detroit and the power and industrial boilers in the region add vessel, tank and piping attachment welds. People looking for magnetic particle inspection services in Michigan usually have one of these field jobs in mind, and the written procedure is tailored to it.
What MT finds and what it misses
Magnetic particle inspection works only on ferromagnetic material: carbon steel, low-alloy steel and most martensitic and precipitation-hardened steels. When a part is magnetized, a crack or seam that crosses the field leaks flux, and fine iron particles gather over it as a sharp line. The method finds surface-breaking cracks, laps, seams, quench cracks, grinding cracks and forging bursts, and flaws just below the surface. On forged and heat-treated steel it is the standard check for the thin, tight cracks that a visual look cannot see.
It cannot examine austenitic stainless steel, aluminum, magnesium, brass or most nickel alloys, which are not ferromagnetic; those parts need penetrant testing. A crack that runs parallel to the field does not show, so each area is examined in two directions about ninety degrees apart. MT sensitivity drops quickly with depth, and it does not size depth. Heavy paint, phosphate or oxide layers and rough surfaces weaken the indication. Some indications come from geometry, magnetic writing or changes in microstructure, and the technician must separate those non-relevant indications from true defects before anything is rejected.
Codes, specifications and Michigan requirements
Code work follows ASME Section V Article 7, with ASTM E1444 for the practice and ASTM E709 as the guide. Acceptance comes from the governing document: ASME Section VIII Division 1 Appendix 6 for vessels, ASME B31.3 paragraph 344.3 and Table 341.3.2 for process piping, AWS D1.1 for structural welds, and AWS D1.5 for bridge welds on the state highway system. Forged steel is often examined to ASTM A275, steel castings use the surface acceptance criteria of ASTM A903 with reference photographs from ASTM E125, and automotive parts follow the customer drawing and quality system, which can be stricter than any consensus standard. The procedure names whichever document governs.
Michigan regulates boilers and pressure vessels through the Boiler Division of the Bureau of Construction Codes within the Department of Licensing and Regulatory Affairs, and the state adopts the National Board Inspection Code for repairs and alterations. MT after a repair weld is typically part of the record a state or insurance inspector reviews. Michigan also runs its own OSHA-approved state plan, administered by MIOSHA. Where API 510, 570 or 653 applies, the owner-user authorized inspector remains responsible for the inspection, and Atlantis reports the MT results to that inspector.
How the examination is done
The technician reviews the procedure, checks the yoke lifting power, cleans the area and sets up the lighting. Article 7 requires an AC yoke to lift at least 10 pounds at the maximum pole spacing used, and a DC or permanent-magnet yoke at least 40 pounds. The yoke is placed across the weld or part, particles are applied dry or as a wet suspension from an aerosol or a squeeze bottle, the field is applied while the particles are on the surface, and the area is examined. The yoke is then turned about ninety degrees and the examination repeated. Prods are limited to places where a yoke will not reach and where arc burns on the surface are acceptable.
Fluorescent wet particles give the highest sensitivity on machined and fatigue-critical steel and are viewed under UV-A light in a darkened area; the procedure sets the UV-A intensity and the ambient white light limit. Visible contrast particles over white paint suit welds in lit areas. Field strength is verified with an indicator or a meter. After the examination, parts are demagnetized when residual fields would affect later welding, machining, bearings or sensors, and the residual field is measured.
Forgings, castings and tooling: what MT shows
Forged and cast steel fail in characteristic ways, and knowing them helps the technician read an indication. Forging laps and seams appear as straight or slightly curved lines that run with the grain flow. Quench and grinding cracks tend to form a network or run square to the grinding direction. Casting defects such as hot tears and cold shuts are rougher and more irregular, and shrinkage near gates and risers shows as clusters. Fatigue cracks in tooling and in-service parts start at a notch or a weld toe and grow in a clean line across the main stress direction. Each pattern points to a different cause, so the report records orientation and location and not just length.
Press and tooling steel brings its own issues. Die sets, tie rods, press crown welds and clamp fixtures see repeated loading, and cracks often start at repaired welds and sharp corners. Because the owner usually wants to know whether a part can run another shift, the procedure sets a clear accept or reject limit before the work starts and the technician marks the exact crack location on the part with a paint stick for the maintenance crew.
| Component | Typical concern | Reference |
|---|---|---|
| Press frames, die sets, tie rods | Fatigue cracks at welds and corners | AWS D1.1, owner specification |
| Forged shafts, hooks and axles | Laps, seams and service cracks | ASTM A275, ASTM E1444 |
| Steel castings | Hot tears, cold shuts and shrinkage | ASTM A903, ASTM E125 |
| Mill rolls, ladle hardware, crane hooks | Surface and fatigue cracks | Mill specification, crane standard |
| Refinery vessel and piping welds | Surface cracking after repair | ASME Section VIII Appendix 6, ASME B31.3 |
Quality system expectations in automotive and steel
Automotive and supplier plants work under customer quality requirements that sit on top of the technical standard: controlled work instructions, calibration records for equipment, retained records and documented corrective action. Our written procedures and reports are built to fit those habits. Every examination is recorded with the procedure revision, the equipment and the technician. Atlantis is certified to ISO 9001 and ISO 14001 for its own management systems. Steel plants add their own mill specifications and safety rules for entry to restricted areas, and the procedure and report format are agreed up front.
Who does the work
Level II technicians perform and interpret the work. They are qualified by their employer under a written practice based on ASNT SNT-TC-1A, while an ASNT NDT Level III approves procedures and reviews reports. Atlantis has no office in Detroit; crews travel to your site with their own equipment, and the schedule is agreed against your shutdown, tooling change or outage. Procedures are written to the code and edition on your purchase order or drawing.
What the MT report contains
- Part, weld or tool identification, drawing reference and location
- Procedure and revision, specification and acceptance table applied
- Equipment: yoke or prod, current type, particle type and carrier, lifting-power check, UV-A and white light readings
- Technician name and qualification level
- Each indication: position, orientation, length, relevant or non-relevant, accept or reject, with photographs or sketches
- Demagnetization and residual field record where required
Planning an MT job in Detroit
Detroit planning starts with the production calendar. Many automotive plants allow outside crews only during planned shutdowns, model changeovers and holiday weeks, so the examination has to fit a tight window and the area must be cleared of other trades. Winters along the Detroit River bring cold steel and lake-effect snow; wet carriers can freeze and contrast paint may not adhere, so a working-temperature limit is agreed or the part is warmed. Summer humidity condenses on cold forgings and tooling. Plants require orientation, lockout coordination and often a hot-work permit, and mills have restricted areas where a visit has to be scheduled. Share your list of parts or welds, materials and acceptance criteria early so the crew can arrive prepared.
MT, PT or UT for your Detroit job
Use MT for ferromagnetic steel when the concern is surface or near-surface cracking: forgings, shafts, hooks, structural welds and tooling. Use liquid penetrant testing in Detroit for aluminum castings, stainless parts and other non-magnetic material. Use ultrasonic testing in Detroit when you need wall thickness, weld volume or the depth of a crack. See the national MT service page, the MT guide, the Article 7 explainer and the Michigan inspection hub for related services.
Training your own MT technicians in Detroit
Plants and suppliers that want in-house magnetic particle capability can use MT Level 1 training and MT Level 2 training. The Detroit NDT training page explains enrollment, and NDT practice tests help candidates prepare. If your written practice needs updating, see written practice development.
Frequently asked questions
Do you provide magnetic particle inspection services in Michigan?
Yes. Technicians are mobilized to Detroit and other Michigan plants, forge shops and job sites to examine ferromagnetic steel with yokes and wet or dry particles, using a written procedure to the specification or code in your contract.
Can you inspect forgings and castings with MT?
Yes, where the part is ferromagnetic. Forged steel is commonly examined to ASTM A275, steel castings to the surface acceptance criteria of ASTM A903, and automotive parts to the customer drawing. Atlantis uses portable equipment and works with the plant on setup.
Which automotive components are examined by MT?
Typical parts are crankshafts, axle shafts, steering knuckles, connecting rods and gear blanks in production, and press frames, die welds, robot fixtures and crane hooks in maintenance. Atlantis field work focuses on the maintenance and weld repair side.
What cannot be examined with magnetic particles?
Austenitic stainless steel, aluminum, magnesium, copper alloys and most nickel alloys are not ferromagnetic, so MT cannot examine them. Those parts are examined by liquid penetrant testing, which finds cracks open to the surface.
Do you use fluorescent particles under UV-A light?
Yes, when the procedure calls for the extra sensitivity. The area is darkened, the UV-A intensity and white light are measured and recorded, and the technician allows time for eye adaptation before the examination starts.
Is demagnetization included?
Where residual magnetism could affect welding, machining, bearings or sensors, the part is demagnetized and the residual field is measured. Where it does not matter, the procedure records that demagnetization was not required.
How do you handle winter conditions in Detroit?
The procedure states a minimum working temperature for the carrier and the contrast paint. Cold parts are warmed or sheltered, and dry powder may be used where it is qualified. Outdoor jobs are scheduled to avoid snow and wind.
What quality documents come with the job?
The report records the procedure revision, equipment checks, technician level, indication locations and sizes, and accept or reject results. It can be formatted to fit a customer quality system, and it is reviewed by an ASNT Level III.
How do I request an MT quote for Detroit?
Send the part or weld list, materials, governing specification, location and your shutdown or outage window through the quote request. Expect a reply inside one business day, with questions about access, temperature and the acceptance table.
Can you mark the exact crack location for the maintenance crew?
Yes. Each relevant indication is located on the part or weld, marked with a paint stick or tape where the owner permits, photographed and entered on a sketch, so the repair crew can find it and the following re-examination checks the same spot.
Inspection and training around Detroit
- Ultrasonic testing (UT) in Detroit
- Liquid penetrant testing (PT) in Detroit
- Magnetic particle inspection services
- NDT inspection services in Michigan
MT by industry for Detroit: Automotive Manufacturing.
MT by job: Magnetic particle weld inspection · Magnetic particle inspection of lifting equipment · Magnetic particle inspection of castings and forgings · Magnetic particle inspection of structural steel and bridges.
Training your own technicians: MT Level 1 training · MT Level 2 training · NDT training for Detroit technicians.
Request an MT inspection quote for Detroit
Send the component and material, the quantity, the code or specification and the site address. We reply within one business day with the scope, the mobilization plan and a quote. Request a quote for magnetic particle inspection in Detroit.
Need magnetic particle testing (MT) done, or learned?
Atlantis provides magnetic particle testing (MT) as an inspection service, trains technicians in it, and lets teams practise it on the Practical NDT simulator.