Magnetic Particle Inspection (MT) in Wichita, Kansas
Atlantis NDT sends Level II technicians to Wichita, Kansas for magnetic particle inspection of welds, castings, forgings and structural steel on your site. Mag particle testing finds cracks and other discontinuities at or just under the surface of carbon and low-alloy steel, quickly and with simple equipment. We have no office in Wichita; crews travel to the plant, tank or fabrication floor. For a scoped proposal, request an MT quote for Wichita with the part, the code and the access conditions.
Where magnetic particle inspection is used in Wichita
The steel that holds Wichita's factories up is a natural MPI customer. Aircraft makers and their suppliers rely on heavy tooling, jigs, fixtures and overhead cranes, and that equipment lives at a stress level that eventually opens fatigue cracks at lugs, pin bores and weld toes. Hangars, hoists and lift trucks at the airports and plants carry the same risk. Structural steel in warehouse, plant and bridge work needs weld checks at fabrication and again after repair.
The energy side of the region adds more: pressure vessel nozzle welds, tank shell-to-bottom welds, pump and compressor supports, and the lifting lugs and trunnions on equipment that gets moved. Grain elevators, food and meat processing plants, and rail-served terminals use conveyors, drives and shafts where a surface crack grows quickly if no one looks. Magnetic particle work is the sensible first look at any of these ferromagnetic parts.
What MT finds and what it misses
The method magnetizes the part so that any crack crossing the field creates a small leakage that attracts fine iron particles. The indication shows up as a sharp line, usually within a minute of application. It works on ferromagnetic material only, which means carbon steel and most low-alloy steel, and it does not work on austenitic stainless steel, aluminum or titanium. It finds surface-breaking flaws and some shallow subsurface ones, but not deep embedded flaws.
Direction matters. A crack parallel to the magnetic field produces almost no indication, so each area is examined with the field applied in two directions at roughly right angles. Paint, thick scale, weld spatter and oil reduce sensitivity and can hide a small crack. Residual magnetism after the test can interfere with welding or damage bearings, so demagnetization is part of the procedure when it matters. The technician records both what was tested and what could not be reached.
Codes and acceptance criteria in Kansas work
Magnetic particle work is governed by ASME Section V Article 7, which covers the method, the equipment and the technique. ASME Section VIII Division 1 Appendix 6 gives methods and acceptance for pressure vessels, ASME B31.3 paragraph 344.3 covers process piping, AWS D1.1 sets criteria for structural welds, and AWS D1.5 applies to steel bridges. For general industry, ASTM E1444 is the practice and ASTM E709 the guide. Our walkthrough of Article 7 requirements helps owners write a procedure that an examiner can follow.
The Kansas boiler safety act lists exemptions for some pressure equipment, including vessels built before 1999 and certain refinery equipment inspected in-plant. Confirm with the jurisdiction which category your vessel sits in. For API 510, 570 or 653 work the owner's authorized inspector stays responsible for the inspection; Atlantis performs the examination and reports the crack indications found.
How the work is done
Field work usually uses an AC electromagnetic yoke, since it is portable and sensitive to surface cracks. A yoke must lift a defined test weight at the pole spacing in use, and the technician checks that lift before the job and keeps the record. For prods or a DC yoke, the same attention applies to current and pole spacing. Visible dry or wet particles work in normal light on a clean surface; fluorescent particles are used in a darkened area under UV-A light when higher sensitivity is needed on a critical weld.
The sequence is clean, magnetize, apply particles during magnetization, examine, record, and demagnetize if required. A field indicator or a pie gage confirms that the field is strong enough in the area under examination. The technician examines each area in two directions, marks relevant indications with a paint pen or photograph, and then evaluates them against the stated acceptance criteria.
Choosing a magnetizing technique for the part
The right technique depends on the shape and what you are looking for. A yoke is ideal for welds, plate edges and open surfaces because the field runs between the poles and can be turned ninety degrees for the second pass. Prods push current directly through the part and give a circular field around the current path, which suits thick weldments and castings, but they can burn the surface if the contact is poor, so many specifications restrict their use. Coils wrap a field around shafts and long parts, and central conductors suit bores and rings. For a crane hook or a pin, a combination of circular and longitudinal fields is often needed to reveal cracks in every direction.
Field strength is checked, not assumed. A pie gage or a shim indicator placed on the surface shows whether the field is strong enough to form an indication of the right sensitivity, and the technician moves the yoke so that overlap is adequate on every pass. On a long weld, the examiner works in overlapping segments, marks the boundaries, and examines each segment twice before moving on. This is slow-looking work, and it is what makes the result reliable.
Wet and dry particles: choosing between them
Dry powder is convenient on rough, hot or outdoor surfaces, and it is the common choice for field weld checks on structural steel. It is blown onto the part in a light cloud while the yoke is energized and is sensitive to larger surface cracks. Wet suspension particles, carried in water or oil, give much higher sensitivity to fine cracks and are the standard for critical welds and machined surfaces. The suspension is applied by spray while the field is active, and the bath concentration is checked with a settling test so the particle load is within the procedure's range.
Contrast matters as well. Black particles on a white contrast paint show up crisply on a clean weld, red or gray dry powders suit dark surfaces, and fluorescent particles in a darkened area under UV-A light reveal very fine indications that visible particles would miss. We choose the combination to suit your code, the surface and the access conditions, then write it into the procedure so the examination can be repeated later by someone else.
Typical Wichita parts and the cracking each one tends to develop
- Overhead crane hooks, lugs and pad eyes: fatigue cracks in the throat, shank and eye after repeated lifts.
- Tooling and fixture welds: toe cracks and cracks at repair welds where heat input was high.
- Pressure vessel nozzle and attachment welds: cracks from thermal cycling and from weld shrinkage stress.
- Tank shell-to-bottom and nozzle welds: cracks at stress concentrations, especially where settlement has occurred.
- Shafts, couplings and drive components: fatigue cracks at keyways, fillets and shoulders.
- Structural connections: weld cracks at beam-to-column joints and brackets after overload or impact.
Each of these calls for different access and a different field direction, which is why a scope that names the parts is more useful than one that only says magnetic particle testing.
Reading indications correctly
Not every particle line is a crack. Magnetic writing from contact with another magnet, changes in section, sharp fillets, the edge of a weld and the boundary between weld metal and base metal all collect particles in lines that look serious and are not. A trained Level II separates relevant indications, which come from real discontinuities, from nonrelevant ones, which come from the shape or magnetic properties of the part. When in doubt, the technician cleans the area, demagnetizes, and repeats the test with a different technique or direction. Indications that stay are measured and compared with the acceptance table: linear indications are usually evaluated by length, and rounded ones by size and spacing.
Who does the work
Our crews are qualified under the company's written practice, based on ASNT SNT-TC-1A. A Level II sets up the equipment, performs the test and evaluates indications; an ASNT Level III approves the procedure and reviews the final report. Procedures here are approved by Anoop Rayavarapu, ASNT NDT Level III in UT, RT, MT, PT and VT. We follow your customer's procedure when it is provided, and our written practice development service is available if your own program needs updating.
What the MT report contains
The report states the part or weld identification, the material and surface condition, the procedure and revision, the magnetizing method, the particle type and carrier, the yoke or equipment identification with its last verification, the technician and level, and the date. Indications are listed with location, orientation and size, sketched or photographed, and each is dispositioned as accepted or rejected against the code. Areas not examined are called out, so the reader is never left wondering whether a corner was reached.
Planning an MT job in Wichita
Wichita's hot, humid summers make heat a factor for fluorescent work in enclosed areas, since darkening a space often means shutting out ventilation. Cold winter days can make surfaces damp or frosted, which affects particle suspension; a clean, dry surface is the first requirement. Spring storms with hail and wind can close exterior work, and tornado warnings stop all field activity on most sites. Plants may require orientation, badging, hot-work or confined-space permits before a crew can begin. We ask for site rules in the first call and plan the mobilization around your outage and access windows.
MT versus UT and PT for your Wichita job
Magnetic particle testing is usually the fastest way to check carbon and low-alloy steel for surface cracking. If the metal is stainless, aluminum or another non-magnetic material, liquid penetrant testing in Wichita is the usual choice. If you need to know about wall loss or about flaws inside a weld, ultrasonic testing in Wichita answers a different question. Our MT versus PT comparison and the national page on magnetic particle testing go deeper on how to choose.
Training your own MT technicians
If your plant does regular crack checks on crane hooks, tooling and weld repairs, it may make sense to train your own examiners. We provide MT Level 1 training and MT Level 2 training, the Wichita training page explains how delivery and practical work are arranged, and our NDT practice tests help candidates prepare. The employer certifies its own technicians under SNT-TC-1A.
Frequently asked questions
What materials can magnetic particle inspection be used on?
Only ferromagnetic materials, mainly carbon steel and low-alloy steel. It does not work on austenitic stainless steel, aluminum or titanium; for those materials liquid penetrant testing is normally used to find surface-breaking cracks.
Does Atlantis have an office or lab in Wichita?
No. We have no office in Wichita. Level II technicians travel to your plant, tank, fabrication floor or yard with the equipment needed for the agreed scope, and report back under our written practice.
Can MT find cracks under paint?
Thin, tightly bonded coatings may be tolerated if the procedure allows it, but thick paint, scale or weld spatter reduce sensitivity. The procedure states the limit, and the technician may ask for coating removal before examination.
Why is each area examined in two directions?
Flux that runs along the length of a crack barely disturbs it, so the flaw hides. Examining with the field at roughly right angles in a second pass makes sure cracks in any orientation have a chance to show up.
Do you use fluorescent or visible particles?
Both are available. Visible particles are common for routine weld checks in normal light, while fluorescent particles under UV-A light in a darkened area give higher sensitivity for critical welds, as the procedure and code require.
Is demagnetization necessary after testing?
Sometimes. Residual magnetism can interfere with later welding, machining or bearing operation, so the procedure calls for demagnetization when those risks apply, and the report records whether it was done and how it was checked.
Which standards do your MT reports follow?
Typical references are ASME Section V Article 7, ASME Section VIII Division 1 Appendix 6, ASME B31.3, AWS D1.1 and D1.5, and ASTM E1444. The report names the procedure and the acceptance criteria that were applied.
How do I get a quote for MT in Wichita?
Send the part or weld description, material, surface condition, governing code and access details through the contact form or the quote link on this page. We reply within one business day with questions or a proposed scope.
Can you train our staff in magnetic particle testing?
Yes. We offer MT Level 1 and Level 2 training with Level III oversight. Your company writes its own written practice and certifies its own technicians; we help with the program, the training and the examinations.
Inspection and training around Wichita
- Ultrasonic testing (UT) in Wichita
- Liquid penetrant testing (PT) in Wichita
- Magnetic particle inspection services
MT by industry for Wichita: Aviation & Aerospace · Wind Energy.
MT by job: Magnetic particle weld inspection · Magnetic particle inspection of lifting equipment · Magnetic particle inspection of castings and forgings · Magnetic particle inspection of structural steel and bridges.
Training your own technicians: MT Level 1 training · MT Level 2 training · NDT training for Wichita technicians.
Request an MT inspection quote for Wichita
Send the component and material, the quantity, the code or specification and the site address. We reply within one business day with the scope, the mobilization plan and a quote. Request a quote for magnetic particle inspection in Wichita.
Need magnetic particle testing (MT) done, or learned?
Atlantis provides magnetic particle testing (MT) as an inspection service, trains technicians in it, and lets teams practise it on the Practical NDT simulator.