Magnetic Particle Inspection (MT) in Salt Lake City, Utah
Atlantis NDT mobilizes Level II technicians to Salt Lake City sites for magnetic particle inspection of carbon and low-alloy steel: pressure vessel and piping welds, crane and hoist components, mining and smelter structural steel, and rail and fabrication work. Examinations follow a procedure written to ASME Section V Article 7 or the owner's code, and every indication is located, sized and called accept or reject. Use this MT inspection quote request and we reply within one business day.
Where magnetic particle testing is used in Salt Lake City
Magnetic particle inspection earns its place wherever steel is stressed, welded or repaired, and the Salt Lake Valley has plenty of all three. The refineries on the north side of the valley run carbon steel vessels, piping and tanks that need surface crack checks after weld repair or alteration. The copper mining and smelting operations on the valley's west side lean on heavy lifting and haulage equipment, where fatigue cracks start at welded brackets and pin bosses. Rail yards along the Union Pacific corridor, fabrication shops, and steel framing for the city's construction boom round out the demand.
Frequent MT targets here include:
- Weld seams, nozzle attachments and repair areas on carbon steel pressure vessels and process piping.
- Shell-to-bottom and nozzle welds on aboveground storage tanks after repair.
- Crane hooks, shackles, lifting lugs and runway beam welds where a fatigue crack is a safety event.
- Structural connections and weld toes on pipe racks, equipment frames and platforms.
- Fabricated assemblies awaiting final acceptance in shops along the Wasatch Front.
What MT finds and what it cannot
MT works by magnetizing the part and applying fine ferromagnetic particles that gather where a discontinuity leaks magnetic flux. It is strong on surface-breaking cracks and on flaws just under the surface, such as lack of sidewall fusion at a weld toe. It works on ferromagnetic material only: carbon steel and most low-alloy steel yes, austenitic stainless, aluminum and copper alloys no. Because copper and stainless are common at smelters and process plants in this area, we confirm the base metal before committing to the method.
Orientation matters. A crack is found best when the field crosses it at close to a right angle, so the code calls for two examinations with the field in roughly perpendicular directions. Heavy paint, scale or weld spatter reduce sensitivity, and deep subsurface flaws are out of reach. When the answer needs to be about the inside of the weld, UT is the better tool; ultrasonic testing in Salt Lake City covers that.
Techniques used on Salt Lake City jobs
For most field work the technician uses an electromagnetic yoke with articulated legs, which magnetizes without burning the surface and can be walked along a weld. ASME Section V Article 7 requires an AC yoke to lift at least 10 pounds (4.5 kg) at the maximum pole spacing used, and a DC or permanent-magnet yoke at least 40 pounds (18 kg); the technician checks this with a test weight before the job. Prods can drive a stronger field through a thick section, but they risk arc burns on finished surfaces, so many owners restrict or forbid them.
Particles come as dry powder for rough, hot or outdoor work, or as a wet suspension for higher sensitivity. Fluorescent wet particles are viewed under UV-A light in a darkened area, which in daylight means a shroud or tent; visible wet particles on a thin white contrast coating are the practical choice on many outdoor tanks and vessels. After examination, parts that will be welded, machined or placed in service next to sensitive equipment are demagnetized and checked for residual field.
Codes and acceptance criteria that apply in Salt Lake City
The method comes from ASME Section V Article 7, supported by ASTM E1444 and the guide in ASTM E709. Acceptance comes from the construction code: ASME Section VIII Division 1 Appendix 6 for pressure vessels, ASME B31.3 paragraph 344.3 for process piping, and AWS D1.1 for structural steel. For API 510, 570 and 653 repairs and alterations, the owner's authorized inspector decides acceptance of the repair; our report gives that inspector the indication data.
Utah's Labor Commission, through its Boiler, Elevator and Coal Mine Safety Division, oversees boilers and pressure vessels under rule R616-2, so weld repairs on regulated equipment normally follow the National Board Inspection Code. OSHA process safety management also expects mechanical integrity work to follow recognized and generally accepted good engineering practice. For a plain-language reading of the method standard, see Article 7 requirements explained.
Surface preparation and contrast
Magnetic particles collect only where they can move, so a weld that is wet with oil, caked with scale or covered in spatter will not give a reliable indication. The usual preparation is a wire brush or light grinding of the weld and about an inch of adjacent base metal, followed by a solvent wipe so the carrier or powder can reach the surface. For visible wet work the technician applies a thin white contrast coating first, which turns a dark particle line into something a reviewer can photograph and evaluate.
Roughness is a trade-off. A very rough surface traps particles and creates false indications, while a polished one can make dry powder skid. The procedure states the acceptable surface condition, and the technician records when a location was examined as found rather than cleaned.
Typical findings and how they are handled
Most MT indications on Salt Lake City jobs fall into a few families: crack-like lines at weld toes, linear indications from lack of fusion at the sidewall, laps and seams in rolled shapes, arc strikes and grinding marks. Not every line is a defect. Under the acceptance table in the construction code, rounded indications below a stated size are allowed while any linear crack-like indication is rejected, and relevant indications are measured so the owner can see how close each one is to the limit.
When a crack is found, the usual path is to grind it out under the owner's repair procedure, then re-examine the ground area with MT to confirm the crack is gone before welding. If grinding removes more than the allowed wall, a thickness check by ultrasonic testing follows. Each step is documented so the repair record reads as a continuous story rather than a pile of separate reports.
A sample MT scope for a Salt Lake City refinery repair
A typical request reads like this: a carbon steel vessel nozzle was replaced during a spring shutdown, and the owner wants magnetic particle examination of the new nozzle-to-shell weld, the repair pad welds and the adjacent lifting lugs. The scope names the procedure, the acceptance code, the surface temperature expected, and how scaffolding will be provided. Our technician examines the welds in two perpendicular directions with a calibrated yoke, records indications, and hands the owner's inspector a report ready for the repair package.
Mining and heavy equipment around Salt Lake City
The copper operations on the west side of the valley and the construction industry along the Wasatch Front use some of the heaviest equipment in the state. Haul truck frames, shovel components, crusher structures, rail loading equipment and tower cranes all carry welded steel under repeated load. Cracks in those parts usually start at welded brackets, pin bosses and sharp transitions, and magnetic particle inspection is the routine way to check them during maintenance windows.
Because the parts are large and the work is often outdoors, the technician combines a yoke for the welds with dry powder for rough or hot surfaces, and records the position of every indication on a sketch. Owners use the results to decide whether a crack can be ground out in the field or whether the component needs a shop repair.
Who does the work
MT is performed by technicians qualified under the company's written practice, built on ASNT SNT-TC-1A, in which the employer certifies its personnel. A Level II sets up the equipment, performs the examination and interprets indications; an ASNT Level III approves the written procedure and reviews reports. If your own program needs a procedure written or a practice reviewed, we offer written practice development and Level III consulting.
What the MT report contains
- Component or weld ID, drawing reference, material and governing code.
- Procedure number and revision, technique (yoke, prods or coil), current type and particle type.
- Yoke lifting check, light readings for fluorescent work, and equipment identification.
- Technician name and level, with the Level III who reviewed the report.
- Each indication with location, length and orientation, sketched or photographed, and the accept or reject decision against the named criteria.
- Demagnetization result where it was required.
Planning an MT job in Salt Lake City
Salt Lake City is dry and high, which helps contrast but brings its own issues. Winter nights drop well below freezing, and cold steel changes how wet carriers flow and how long a contrast coating takes to dry, so the procedure has to cover the actual surface temperature. In summer, steel in direct sun can get hot enough to evaporate a wet carrier before the indication forms, which pushes the work toward dry powder or early-morning starts. Dust from dry weather and windblown grit also affects surface cleanliness.
Atlantis keeps no office in Salt Lake City, so technicians travel to your site with their own yokes, lights and test blocks. Plan for refinery badging, hot-work and confined-space permits, access scaffolding and a place to set up shade or a darkening tent. Spring and fall turnaround seasons fill quickly, so give us the dates when you request the quote.
MT, PT or UT for your Salt Lake City job
Pick magnetic particle testing for surface cracks on carbon steel welds, lifting gear and fatigue-critical details. Pick liquid penetrant testing in Salt Lake City for stainless steel, aluminum or any non-magnetic part, and ultrasonic inspection for wall thickness or internal weld flaws. If you are unsure, the MT versus PT comparison explains how to choose, and our national MT service page lists the standard scope.
Training your own MT technicians
A plant that wants to run its own crack checks can start with MT Level 1 training and MT Level 2 training, and see NDT training for Salt Lake City for delivery options. Practice questions are available in the NDT practice tests library. Certification stays with the employer under its written practice.
Frequently asked questions
What materials can magnetic particle inspection be used on?
Only ferromagnetic materials: carbon steel and most low-alloy steels. Austenitic stainless steel, aluminum, copper and titanium cannot be magnetized, so liquid penetrant testing is used on those materials instead. The technician confirms the base metal with a magnet or the material records before any examination starts.
Is yoke magnetization enough for pressure vessel welds in Salt Lake City?
Often yes. A yoke that meets the lifting power check in ASME Section V Article 7 works for most welds. Thick sections, large castings or special geometry may call for prods or coil techniques written into the procedure.
Can MT be done on painted steel?
Thin, well-bonded coatings may be acceptable if the procedure has been demonstrated through them, but heavy or flaking paint reduces sensitivity. The usual practice is to strip the coating at the weld and adjacent base metal before examination.
Does Atlantis have a crew in Salt Lake City?
No. Technicians are mobilized from outside the city to your refinery, plant, yard or shop for the agreed scope, so travel, badging and permits are part of the plan and the quote.
How is a fluorescent MT examination done outdoors?
The area is shaded or enclosed so ambient white light stays low enough for the procedure, UV-A intensity is measured at the surface, and the technician allows time for eye adaptation before evaluating indications. Fluorescent work in open daylight without shade is not acceptable under the usual procedure.
When is demagnetization needed?
When residual magnetism could interfere with later welding, machining, instrument operation or cleanliness of moving parts. The technician checks the part with a field indicator or gauss meter and records the residual field in the report, along with any additional treatment that was needed to bring it below the limit.
Which codes apply to MT on piping and vessels?
The method is ASME Section V Article 7. Acceptance usually comes from ASME B31.3 for process piping, ASME Section VIII Division 1 Appendix 6 for pressure vessels, or AWS D1.1 for structural steel.
Does Utah require inspection of repairs on pressure vessels?
Utah's Labor Commission administers boiler and pressure vessel rules under R616-2, and repairs on regulated equipment generally follow the National Board Inspection Code. Your authorized inspector or the state inspector decides what a repair requires.
How do I get MT technicians trained for my own plant?
Atlantis offers MT Level 1 and Level 2 training aligned to SNT-TC-1A, with practice tests. Your employer then certifies trained people under its own written practice and checks their qualification records.
Inspection and training around Salt Lake City
- Ultrasonic testing (UT) in Salt Lake City
- Liquid penetrant testing (PT) in Salt Lake City
- Magnetic particle inspection services
MT by industry for Salt Lake City: Refining · Mining & Minerals · Water & Wastewater Utilities.
MT by job: Magnetic particle weld inspection · Magnetic particle inspection of lifting equipment · Magnetic particle inspection of castings and forgings · Magnetic particle inspection of structural steel and bridges.
Training your own technicians: MT Level 1 training · MT Level 2 training · NDT training for Salt Lake City technicians.
Request an MT inspection quote for Salt Lake City
Send the component and material, the quantity, the code or specification and the site address. We reply within one business day with the scope, the mobilization plan and a quote. Request a quote for magnetic particle inspection in Salt Lake City.
Need magnetic particle testing (MT) done, or learned?
Atlantis provides magnetic particle testing (MT) as an inspection service, trains technicians in it, and lets teams practise it on the Practical NDT simulator.