Magnetic Particle Inspection (MT) in Pittsburgh, Pennsylvania

Atlantis NDT provides on-site magnetic particle inspection (MPI) in Pittsburgh for welds, forgings, castings, crane hooks, mill components and structural steel. Technicians are mobilized to your plant, shop or job site, examine carbon and low-alloy steel for surface and near-surface cracks to a written procedure, and report each indication against the acceptance criteria you name. To scope a job, use the Pittsburgh MT quote request; we reply within one business day.

Where magnetic particle testing is used in Pittsburgh

Mag particle testing suits Pittsburgh because so much of the region is ferromagnetic steel under cyclic load. Around the Monongahela mills the candidates are roll necks and chocks, couplings and shafts, crane hooks, sheave blocks, ladle trunnions and the weld details on runway girders and mill buildings. Fatigue cracks in this equipment start at the surface, at a notch, a weld toe or a keyway, which is exactly what MT is built to find.

Away from the mills, the work shifts to fabrication and infrastructure. Fabricators in the metro area build pressure vessels, tanks, structural frames and equipment skids, and MT is the common surface check on fillet welds, attachment welds and repairs before paint or hydrotest. Steel bridges across the three rivers carry fatigue-sensitive details such as cover plate ends, stiffener welds and floor-beam connections, where inspection under AWS D1.5 or the owner contract often calls for MT on suspect welds. Gas compressor frames, piping support attachments and the power-plant headers along the rivers add further surface-crack scopes.

What MT finds and what it misses

MT works only on ferromagnetic material: carbon steel, low-alloy steel and most martensitic grades. A magnetic field is induced in the part; a crack or similar discontinuity across the field leaks flux, which holds fine iron particles in a visible line on the surface. It finds surface-breaking cracks, laps and seams, and cracks just under the surface, with sensitivity that drops quickly as the depth increases. Fine, tight fatigue cracks that other methods miss are often easy to see.

The limits are as important as the strengths. Austenitic stainless steel, aluminum, copper and nickel alloys cannot be examined this way, so those parts go to penetrant testing. A flaw lying parallel to the field lines produces little or no indication, which is why Article 7 requires two examinations at roughly right angles. Heavy paint, scale or weld spatter weakens the indication, and sharp geometry can produce non-relevant indications that a trained technician must tell apart from real cracks. MT shows where a crack is, not how deep it goes; depth sizing is a job for UT or grinding.

Codes and acceptance criteria for Pittsburgh MT work

The technique is governed by ASME Section V Article 7 for code work, and by ASTM E1444 for the practice and ASTM E709 for the guide. Acceptance depends on the item: ASME Section VIII Division 1 Appendix 6 for vessels, ASME B31.3 paragraph 344.3 with Table 341.3.2 for process piping, AWS D1.1 for structural welds, and AWS D1.5 for bridge welds, each with its own limits on linear and rounded indications. Forgings and castings use their product specifications, and lifting equipment follows the manufacturer and the applicable crane standard.

Pennsylvania boilers and unfired pressure vessels fall under the state Department of Labor and Industry program, and repairs follow the National Board Inspection Code, so MT after a weld repair is usually part of the record the inspector reviews. Under API 510, 570 and 653 the owner-user authorized inspector stays responsible for the inspection; Atlantis performs the MT and reports indications with location and size so the inspector can decide on repair or acceptance. Covered gas and process sites are also subject to OSHA process safety management, which expects mechanical-integrity inspection by recognized good engineering practice.

How the examination is done

For field work the usual tool is an AC electromagnetic yoke, chosen because it can be set between poles on the weld, moved quickly and used on structures. The Article 7 lifting-power check applies: an AC yoke must lift at least 10 pounds at the maximum pole spacing used, and a DC or permanent-magnet yoke at least 40 pounds. The technician confirms the yoke before use, cleans the surface, applies particles by dry powder or by a wet suspension in aerosol form, magnetizes in one direction, examines, then repeats at about ninety degrees. Prods can be used where a yoke does not reach, but arcing is a risk on finished surfaces, so the procedure says where prods are allowed.

Fluorescent wet particles give the highest sensitivity, and are viewed under UV-A light in a darkened area with the intensity and ambient light limits the procedure states. Visible color-contrast particles over a thin white contrast paint suit well-lit field work. Field indicators or a pie-gage-type indicator confirm the field direction and strength in the part. After inspection, parts are demagnetized if residual fields would interfere with welding, machining, bearing performance or later operations, and the field is checked with a meter.

Reading and judging MT indications in Pittsburgh steel

A magnetic particle indication is only the start of the judgment. The technician classifies each one as relevant or non-relevant. A relevant indication is caused by a discontinuity such as a crack, lap or lack of fusion. A non-relevant one comes from a change in section, a keyway, a sharp thread root, a magnetic writing mark or the boundary of a heat-affected zone, and it can look like a crack until the surface is cleaned and re-examined. Pittsburgh work is full of these: old mill equipment has been repaired, welded, ground and re-machined many times, and each change leaves magnetic transitions that confuse a casual observer. Re-examination after light grinding, a change of magnetizing direction or a switch from dry powder to wet particles usually settles the question.

Relevant indications are then compared with the acceptance table. Linear indications are measured by length, rounded indications by diameter, and clusters by the number inside a defined area. Cracks are rejected under essentially every code. For a lifting device, any crack indication normally means the item is withdrawn until the owner and the manufacturer decide what happens next, so the report has to be exact about where the indication lies and how long it is.

Common MT scopes around Pittsburgh
ComponentTypical concernReference
Crane hooks, lifting beams, sheave blocksFatigue cracking at the throat or shankCrane standard and manufacturer
Runway girder and mill structure weldsToe cracks, repair weldsAWS D1.1
Bridge fatigue detailsStiffener and cover plate weldsAWS D1.5
Vessel and tank attachment weldsFillet and nozzle weld cracksASME Section VIII Appendix 6
Process and power piping weldsSurface cracking after repairASME B31.3, ASME B31.1

Surface preparation and coatings on Pittsburgh steel

Older Pittsburgh steel often carries decades of paint, mill scale and weld spatter. For magnetic particle work the surface needs to be free of loose scale, oil, grease and anything that would hold particles away from a crack or hide an indication. Thin, well-bonded coatings may be acceptable when the procedure has been demonstrated on a coated sample, but thick paint reduces the leakage field and can mask fine cracks, so it is removed locally at the weld or the area of concern. Blasting or wire brushing is the usual preparation; heavy grinding is avoided on fatigue-critical parts because it can create new surface damage. When a part is to be recoated afterward, the owner and the coating contractor should agree the cleanup so particles and contrast paint do not remain under the new film.

Who does the work

Level II technicians perform and interpret the examination. Qualification is by the employer under a written practice built on ASNT SNT-TC-1A, and an ASNT NDT Level III approves procedures and reviews the reports. Procedures are written to the code and edition in your contract, not a generic template. Atlantis has no office in Pittsburgh; the crew travels to your site with yokes, particles, lights and meters, and the schedule is confirmed against your outage or shop window.

What the MT report contains

Planning an MT job in Pittsburgh

Pittsburgh weather affects magnetic particle work more than people expect. Cold steel in winter is slow to take a contrast paint, and some wet carriers become unusable near freezing, so the procedure should state the lowest working temperature or the part should be warmed. Summer humidity condenses on cold pipe and ruins particle mobility. Outdoor fluorescent inspection needs a tent or a shaded enclosure dark enough for the UV-A light, and day work on bridges or outdoor girders is often limited by sunlight. Mill and plant sites commonly need orientation, permits and escort, and elevated welds need access that the owner arranges. Send your outage dates and the weld count early so the crew can be sized.

MT, PT or UT for your Pittsburgh job

Use MT for surface and near-surface cracks in carbon and low-alloy steel, where it is fast and shows cracks plainly. Use dye penetrant inspection in Pittsburgh for stainless steel, aluminum and other non-magnetic materials, or where particles cannot be applied. Use ultrasonic testing in Pittsburgh when you need weld volume examination or crack depth. The national MT service page, the MT guide and the MT versus PT comparison explain the trade-offs, and the Pennsylvania inspection hub lists related services.

Training your own MT technicians in Pittsburgh

Plants that want in-house capability can use MT Level 1 training and MT Level 2 training, with the theory and practice that SNT-TC-1A expects. The Pittsburgh NDT training page describes how enrollment works, and practice tests help candidates prepare.

Frequently asked questions

Do you offer magnetic particle inspection in Pittsburgh?

Yes. Technicians are mobilized to your Pittsburgh plant, fabrication shop or job site to examine welds, forgings, castings and structural steel with yokes, dry powder or wet particles, to a written procedure and the code named in your contract.

What materials can MPI inspect?

Magnetic particle inspection works on ferromagnetic materials only, such as carbon steel, low-alloy steel and martensitic grades. Austenitic stainless steel, aluminum, copper and most nickel alloys are not magnetic, so those parts are examined by liquid penetrant testing instead.

How deep can mag particle testing find cracks?

MT finds cracks open to the surface and cracks lying just beneath it. Sensitivity falls off quickly with depth, so deeper flaws in welds are better examined by ultrasonic testing. MT also does not size crack depth.

Why are two examination directions required?

A crack lying parallel to the magnetic field gives almost no indication. ASME Section V Article 7 therefore calls for two examinations with the field at roughly right angles, so cracks running in any direction cross the flux and show up.

Do you use fluorescent or visible particles on site?

Both. Fluorescent wet particles are used where sensitivity is critical and the area can be darkened under UV-A light, while visible color-contrast particles suit well-lit outdoor work. The procedure states which applies, including the light levels required.

Is demagnetization part of the job?

When residual magnetism would affect welding, machining, bearings, instruments or later steps, the part is demagnetized and the field is checked with a meter. If no later step is affected, the procedure records that demagnetization was not required.

Which acceptance criteria do you apply to MT indications?

Acceptance comes from the construction code or contract, such as ASME Section VIII Division 1 Appendix 6, ASME B31.3 Table 341.3.2, AWS D1.1 or AWS D1.5. The code and edition are confirmed in the quote and recorded on the report.

Can MT be done on painted steel or in cold weather?

Thin coatings can be examined if the procedure shows adequate sensitivity, and heavy coatings are removed locally. Cold affects carriers and contrast paint, so the lowest working temperature is stated in the procedure and the part is warmed if necessary.

How do I get a quote for MT inspection in Pittsburgh?

Send the component list, materials, number of welds or parts, governing code, location and preferred dates through the quote request. We reply within one business day to confirm scope and plan how the crew will be mobilized.

Can MT be done on welds that have a coating or have been recently repaired?

Thin, bonded coatings may be examined if the procedure has been demonstrated on a coated sample. Heavy coatings are removed locally. Repaired welds are examined after cooling, usually after the grind-out and weld, and again at the stage the code requires.

Inspection and training around Pittsburgh

MT by industry for Pittsburgh: Pipeline · Power Generation · Fabrication & Welding · Steel & Primary Metals.

MT by job: Magnetic particle weld inspection · Magnetic particle inspection of lifting equipment · Magnetic particle inspection of castings and forgings · Magnetic particle inspection of structural steel and bridges.

Training your own technicians: MT Level 1 training · MT Level 2 training · NDT training for Pittsburgh technicians.

Request an MT inspection quote for Pittsburgh

Send the component and material, the quantity, the code or specification and the site address. We reply within one business day with the scope, the mobilization plan and a quote. Request a quote for magnetic particle inspection in Pittsburgh.

Need magnetic particle testing (MT) done, or learned?

Atlantis provides magnetic particle testing (MT) as an inspection service, trains technicians in it, and lets teams practise it on the Practical NDT simulator.