Magnetic Particle Inspection (MT) in Peoria, Illinois

Atlantis NDT performs magnetic particle inspection on carbon and low-alloy steel for Peoria, Illinois owners: welded frames and booms from heavy-equipment manufacturing, castings and forgings, crane and rigging components, grain-facility steelwork, bridge and structural connections, and repair welds on boilers and vessels. Crews travel to your Peoria facility carrying yokes, particles, a light meter and field indicators, follow a written procedure, and write up results against whichever code your contract cites. Request a mag particle testing quote for your Peoria site and we reply within one business day.

Where magnetic particle testing is used around Peoria

Peoria is a machine-building city. Companies that make earthmoving and agricultural equipment have shaped its steel economy for generations, and the supply chain around them includes foundries, forge shops, weld fabricators and machine shops. The same region moves grain by river and rail, runs large hospital central plants, and relies on a handful of river bridges. Heavy equipment is dynamically loaded and welded from thick plate, so fatigue cracks at weld toes and stress concentrations are the everyday damage mechanism, and those cracks begin on the surface, where magnetic particle inspection is strongest.

Examples of MT work in this market:

What magnetic particle inspection finds, and what it misses

Magnetizing a steel part makes any crack or seam that reaches the surface leak flux, and fine ferrous particles gather at the leak, drawing the flaw as a line you can see. The method works only on ferromagnetic material: carbon and low-alloy steels and martensitic grades qualify, while austenitic stainless steel, aluminum and copper do not. It is sensitive to surface and slightly subsurface discontinuities and loses sensitivity quickly with depth.

It cannot measure wall thickness, find deep internal flaws, or reveal a crack that lies along the field direction, which is why two orientations are required. Surface preparation is also part of the method: heavy scale, oil and thick paint block particle build-up and are removed first. On large castings and thick welds, the technician may need to move the yoke across overlapping positions to cover the whole surface, which takes time that a quote should allow for.

Codes and acceptance criteria that govern MT work

MT is written to ASME Section V Article 7, set out in our Article 7 explainer, together with ASTM E1444 and ASTM E709. Acceptance comes from the construction code: ASME Section VIII Division 1 Appendix 6 for vessels, ASME B31.3 paragraph 344.3 and Table 341.3.2 for process piping, AWS D1.1 for structural steel and AWS D1.5 for bridge welds. Work on equipment managed under API 510, 570 or 653 follows the construction code, with the owner's authorized inspector remaining responsible for the inspection.

Illinois covers boilers and pressure vessels through the Boiler and Pressure Vessel Safety Act, administered by the Division of Boiler and Pressure Vessel Safety within the Office of the State Fire Marshal. The Act adopts the ASME Code and the National Board Inspection Code and sets rules for repair and alteration, so MT of a repair weld on registered equipment often forms part of the file the commissioned inspector reviews.

How the examination is done

Field work usually uses an electromagnetic yoke. The AC yoke meets the lifting-power check in Article 7 for surface examination, and DC or permanent-magnet yokes need a higher pull to qualify. Prods, coils and cables are options where a yoke cannot reach, as the procedure allows. Dry powder is the choice on hot, rough or field-welded surfaces; wet visible and wet fluorescent suspensions deliver more sensitivity on cleaned machined parts, and fluorescent work requires a darkened area with a measured UV-A source.

The technician verifies field strength with a pie gauge or shim, applies particles during magnetization, inspects overlapping zones, then repeats at a second orientation. Where a leftover field would harm later machining, welding or bearing life, the part is demagnetized and checked with a gauss meter.

Foundry, forge and fabrication shop work

Parts brought to a bench or booth are easier to examine than assemblies left in place, because they can be cleaned, magnetized in several directions with a stationary unit and lit properly. Casting examination looks for hot tears, shrinkage cracks and cold laps; forgings for laps and seams; machined parts for grinding cracks and heat-treatment cracks. We take care to separate real cracks from non-relevant indications at sharp corners, keyways and thread roots, where flux naturally concentrates, so owners do not scrap good parts.

For weld fabrication, the examination is staged: after root or hot pass where the code requires, after back-gouging, and after the final pass and any post-weld heat treatment, since heat treatment itself can crack heavy sections. Each stage is a separate record.

Lifting equipment and fatigue-prone steel

Hooks, chains, lugs and spreader beams carry the load that hurts people when they fail, and they are a frequent reason Peoria owners call for mag particle work. Hooks crack at the saddle and shank, lugs crack at the pin-hole edge, and welded attachments crack at their toes. The examination normally supports a periodic inspection program set by the owner's engineer or crane inspector. We examine the load-bearing zones the program names, record each item by tag, and report rejectable indications so that the item stays out of service until it is repaired or replaced.

Fatigue also appears in conveyor supports, vibrating equipment skids and bridge-related connections, where repeated cycles open cracks slowly. These are worth re-examining at intervals chosen from the first findings.

Preparing surfaces and judging indications

Bare, dry steel gives clearer results, so spatter, loose scale, grease and thick paint are removed from the examination area and a short distance beyond each weld. Contrast paint helps dry and wet visible particles show against dark steel. Not every particle line is a flaw: magnetic writing, changes of section and weld edges produce non-relevant lines, while dirt and lint cause false ones. The technician separates them by re-cleaning, remagnetizing and, where needed, trying another field direction.

Only relevant indications are measured against the acceptance limits. Linear, rounded and clustered indications are judged differently by most codes, so the report states shape and size, which lets the owner's engineer choose whether to grind, repair or accept.

Who performs and reviews the work

Peoria jobs are staffed by examiners who travel in for each agreed scope. Their qualifications come through the company's written practice, built on ASNT SNT-TC-1A. A Level II technician sets up equipment, performs the examination and interprets indications, and an ASNT Level III approves procedures and reviews reports. If your company holds its own written practice, we can follow it, and the written practice development and Level III consulting pages describe how procedures are built or aligned.

Staged examination during weld fabrication

On heavy fabrications the examination is often staged: after the root or hot pass where the code requires it, after back-gouging, after the final pass, and again after any post-weld heat treatment, since stress relief can itself open cracks in thick sections. Each stage is its own record, so a rejected indication can be traced to the weld step that produced it.

Documenting and demagnetizing

Parts that have been magnetized can hold a residual field that attracts chips, disturbs arc welding or accelerates bearing wear. When the procedure or the owner requires it, the part is demagnetized and measured with a gauss meter, and the reading is recorded. Large welded assemblies often need no demagnetizing unless they will be welded or machined next, and the quote says which applies.

What the MT report contains

The report names the part or weld identifier, drawing, material and surface condition, the procedure and revision, equipment and calibration status, the technique used, field verification, the technician and level, and the date. Each indication is located, oriented and sized, and judged against the named acceptance criteria. Sketches or photos accompany rejectable indications, and the record states whether demagnetization was done and verified.

Typical MT scopes and the references behind them

Common magnetic particle scopes for Peoria-area owners
ComponentWhat is examinedTypical reference
Heavy-equipment frames and boomsWeld toes and stress-concentration cracksAWS D1.1, ASTM E1444
Castings and forgingsHot tears, laps and seamsASTM E709, owner specification
Crane hooks and lifting gearSaddle, shank and pin-hole cracksASME Section V Article 7
Grain facility structural steelConnection and support weldsAWS D1.1
Bridge steel connectionsFillet and groove weldsAWS D1.5
Boiler and vessel repairsExcavations and repair weldsASME Section VIII Appendix 6, NBIC

Planning a magnetic particle job in Peoria

Peoria's average January low is close to 17 degrees Fahrenheit and snow is frequent, so outdoor mag particle work on frames, towers and bridge steel has to deal with frost, snow and cold steel. Wet suspensions can freeze or lose contrast, particle carriers behave differently, and dry powder is often chosen for cold field work. In summer, with July highs near 86 and high humidity, dew and sweating on steel can affect particle adhesion until surfaces are dried. Wind blows dry powder away, so shelter or a different technique may be needed on exposed structures.

Plant schedules matter: heavy-equipment lines run in shifts, and grain facilities have harvest peaks, so MT is typically arranged for planned downtime. Expect safety orientation, lockout, hot-work and, in grain areas, hazard classification checks. Fluorescent examination needs shade; on an open floor that usually means a booth. The quote lists what the owner is asked to provide, such as clean access and lighting.

MT, PT or UT for your Peoria job

Use MT as the quick surface check on carbon and low-alloy steel. If a part is stainless, aluminum or another non-magnetic alloy, liquid penetrant testing in Peoria is the surface method, and for wall loss or internal weld flaws ultrasonic testing in Peoria is the right choice. The national magnetic particle testing page, the complete MT guide and the MT versus PT comparison help with the selection, and the Illinois inspection services page shows how the services combine.

Training your own MT technicians

Companies that want in-house mag particle capability can begin with the MT Level 1 course and continue to the MT Level 2 course, using the NDT practice tests for preparation. Local details are on the Peoria NDT training page. The employer issues the qualification under its written practice, which is how SNT-TC-1A is designed to work.

Frequently asked questions

Can magnetic particle inspection be done on heavy equipment frames in Peoria?

Yes. Technicians travel to your plant or yard and examine weld toes, repair excavations and stress-concentration areas on frames and booms with portable yokes, within the limits of surface condition and access.

Do you inspect castings and forgings?

Yes, where they can be cleaned and magnetized. Examination looks for hot tears, shrinkage cracks, laps and seams, and it separates relevant indications from non-relevant ones at corners, keyways and thread roots.

Which materials can MT examine?

Only ferromagnetic materials such as carbon steel, low-alloy steel and martensitic grades. Austenitic stainless steel, aluminum and copper cannot be magnetized, so liquid penetrant testing is used for those.

Can you do MT outdoors in a Peoria winter?

Often, with changes. Dry powder or a cold-rated suspension is used, frost and snow are cleared, and extreme cold or wind may mean the work is moved to a better window.

Why must a part be examined in two directions?

A crack running parallel to the magnetic field leaks almost no flux and may not show. Magnetizing again at roughly ninety degrees ensures that cracks in either direction are detected.

Do you check crane hooks and rigging?

Yes. Hooks, lugs, chains and below-the-hook devices are examined at load-bearing zones and welds, using the criteria in the owner's procedure or the standard that applies to the equipment.

Does Atlantis have a Peoria office?

No. Atlantis has no office in Peoria. Technicians are mobilized to your site for the agreed scope, and your quote is based on your drawings, access conditions and the code that applies.

Can our staff learn MT through Atlantis courses?

Yes. The MT Level 1 and Level 2 courses prepare candidates, and your company qualifies them under its written practice based on SNT-TC-1A. The final qualification comes from the employer.

Inspection and training around Peoria

MT by industry for Peoria: Fabrication & Welding.

MT by job: Magnetic particle weld inspection · Magnetic particle inspection of lifting equipment · Magnetic particle inspection of castings and forgings · Magnetic particle inspection of structural steel and bridges.

Training your own technicians: MT Level 1 training · MT Level 2 training · NDT training for Peoria technicians.

Request an MT inspection quote for Peoria

Send the component and material, the quantity, the code or specification and the site address. We reply within one business day with the scope, the mobilization plan and a quote. Request a quote for magnetic particle inspection in Peoria.

Need magnetic particle testing (MT) done, or learned?

Atlantis provides magnetic particle testing (MT) as an inspection service, trains technicians in it, and lets teams practise it on the Practical NDT simulator.