Magnetic Particle Inspection (MT) in Memphis, Tennessee
Atlantis NDT sends Level II technicians to Memphis, Tennessee to perform magnetic particle inspection (MPI, also called mag particle testing) on welds, castings, forgings and structural steel. Typical work includes weld toes on fabricated steel, lifting equipment at river and rail yards, and repair welds on plant equipment. Tell us the part, the material and the code, and we will plan the examination. Request an MT quote for your Memphis site.
Where magnetic particle inspection is used in Memphis
Few American cities handle as much heavy freight as Memphis. The Mississippi River port, a dense rail network, interstate highways and a large air cargo operation all move steel equipment, and all of that equipment is subject to cracking from fatigue and overload. The Port of Memphis lists dozens of waterfront facilities, with President's Island carrying most of them, and the terminals there handle steel, cement, fertilizer, grain and petroleum products. Cranes, hoppers, conveyor frames, barge-loading structures and the pads and padeyes that lift them are all carbon steel and all candidates for MT.
Inland, fabrication shops and metal processors weld structural steel, tanks, trailers and machinery frames. Rail yards and shops deal with couplers, truck frames and welded repairs. Warehouses and distribution centers use heavy racking, lift trucks and dock equipment, where a cracked weld can drop a load. Power and process plants add pressure-equipment attachment welds, support lugs, nozzle welds and the repair welds that follow maintenance outages.
The common thread is carbon or low-alloy steel with surface-breaking cracks at weld toes, fillet roots and sharp changes of section. This is the situation magnetic particle testing is built for.
What MT finds, and where it stops
MT works only on ferromagnetic material. When the part is magnetized, a crack that breaks the surface or lies just beneath it interrupts the magnetic field and pulls fine iron particles into a visible line. The method is fast and sensitive for tight cracks, laps, seams and lack of sidewall fusion at the surface, and it works through thin non-magnetic coatings if the procedure allows.
It does not work on austenitic stainless steel, aluminum, copper or most nickel alloys, because those are not ferromagnetic. It also loses sensitivity with depth: a flaw more than a short distance below the surface will not produce an indication. And the field must cross the discontinuity at a favorable angle. A crack running parallel to the field lines can pass unnoticed, which is why the code requires examination in two directions roughly at right angles.
For non-magnetic Memphis assets such as stainless piping or aluminum structures, liquid penetrant testing in Memphis is the surface method of choice. For wall loss or internal weld defects, see ultrasonic testing in Memphis.
Codes and acceptance criteria
Magnetic particle examination is controlled by ASME Section V Article 7 when the job is under ASME construction or repair rules. The Article sets lifting-power requirements for yokes, particle and illumination requirements, the two-direction rule, and when demagnetization is required. Acceptance comes from the governing code: ASME Section VIII Division 1 Appendix 6 for vessels, ASME B31.3 paragraph 344.3 with Table 341.3.2 for process piping, ASME B31.1 for power piping, AWS D1.1 for structural steel and AWS D1.5 for bridge steel. ASTM E709 is the general guide and ASTM E1444 the practice that many specifications reference.
Tennessee's boiler and pressure vessel program, run through the Workplace Regulations and Compliance division of the state labor department, inspects boilers and larger unfired pressure vessels, and repairs follow the National Board Inspection Code. When an MT examination is part of a repair, the examination requirements are written into the repair plan that your owner-user inspector or authorized inspection agency accepts. Atlantis performs and reports the examination; it does not take over the owner's inspection responsibilities under API 510, API 570 or API 653.
How an MT examination is done
Surface preparation comes first. Paint, scale, weld spatter and oil must be removed enough for particles to move and for the part to be magnetized properly. Weld surfaces may need light grinding if the profile masks indications.
For field work the portable electromagnetic yoke is the main tool. An AC yoke is checked for a lifting power of at least ten pounds at the maximum pole spacing used, while a DC or permanent-magnet yoke must lift at least forty pounds. The yoke is placed across the weld, particles are applied while the field is on, and the area is examined for indications. The yoke is then rotated roughly ninety degrees and the examination repeated, so that cracks in any direction are caught. Prods are an alternative on thick sections or in shops where arcing is controlled. Dry powder suits rough or hot surfaces, and wet visible particles suit smoother surfaces. Wet fluorescent particles give the highest sensitivity, viewed under UV-A light in a darkened area, and they are common in shop work on critical parts.
Indications are classified as relevant or non-relevant, measured, and compared with the acceptance table. Disputed indications can be wiped clean and re-examined, and when a part will be welded, machined or put into rotating service, demagnetization removes residual fields that could interfere. Our magnetic particle testing page and the MT complete guide explain the technique further, and the Article 7 explainer walks through the code requirements.
Who does the work
MT in Memphis is performed by technicians qualified under Atlantis's written practice, which follows ASNT SNT-TC-1A. A Level II sets up the equipment, performs the examination, interprets and records the results. An ASNT Level III approves the written procedure and reviews the report. The company is led by Anoop Rayavarapu, ASNT NDT Level III in UT, RT, MT, PT and VT. Atlantis has no office in Memphis, so technicians are mobilized to your site for the agreed scope.
If your fabrication or maintenance team needs its own MT procedure to a specific code, our Level III consulting can write and qualify it.
What the MT report shows
- Part or weld identification, location and drawing reference.
- Procedure number and revision and the code it implements.
- Equipment: yoke type, measured lifting power, particle type and lot, and the light meter for visible or UV-A examination.
- Surface condition, technique and the two examination directions.
- Every indication with location and size, and accept or reject against the named table.
- Technician name and qualification level, with the date and results of any re-examination or demagnetization check.
Planning an MT job in Memphis
Heat and humidity are the main practical issues. In summer, steel left in the sun can be too hot for wet particles, which dry out and lose mobility, so the procedure must be qualified for the surface temperature or the work shifted to cooler hours. Wet particle carriers also behave differently in humid air, and rain delays are common on open terminals. In winter, moisture can freeze on shaded steel, and the particle suspension must be kept above its limit.
Most Memphis facilities require badging and safety orientation, and river terminals have their own access control. If fluorescent examination is planned, we need a space that can be darkened, or a portable enclosure, and we agree the lighting arrangement before arrival. Outage seasons in spring and fall bring peak demand, so early scheduling helps.
Typical crack sites on Memphis steel
Knowing where cracks start makes an MT job faster and the report more useful. On welded crane runway beams and gantry legs at river and rail yards, fatigue cracks tend to begin at the toes of attachment welds, at the ends of stiffeners and at cope holes, where stress concentrates under repeated load cycles. On barge-loading structures and hopper frames, cracks often begin where a gusset meets a flange or at the weld that joins a lifting lug to the structure, because lifting loads are applied there repeatedly. On trailers and truck frames, fatigue cracks follow the welds that attach cross members and spring hangers, and they grow from the weld toe into the parent plate.
In plant service the pattern changes. Pressure equipment attachment welds, such as support lugs and saddle welds, crack from thermal cycling and restrained expansion. Repair welds are examined because a repair is the area most likely to contain lack of fusion or cracking in the heat-affected zone, particularly on thick or higher-carbon material that was welded without adequate preheat. When we plan the examination, we ask for the original weld map or the repair plan so we can check these areas first and spend the most time where cracks are most likely to form.
Choosing wet or dry particles and visible or fluorescent light
The right particle system depends on the surface, the temperature and the sensitivity the code expects. Dry powder is used on rough as-welded surfaces and on warm steel, where wet carriers would evaporate, and it is sensitive to subsurface indications when used with AC. Wet visible particles in aerosol cans are practical on cleaner machined or ground surfaces and give better sensitivity to fine surface cracks. Wet fluorescent particles are the most sensitive option and are preferred for critical parts, but they need the darkened area and UV-A lamp already described, and the lamp intensity and ambient white light must be measured and recorded.
Contrast paint, a thin white background coat, is often applied to dark or rough steel before visible wet particles to improve the visibility of indications. Particle concentration for wet suspensions must be checked with a settling test at the start of work and whenever the bath looks weak. These checks add minutes to a job, but they are what separates a defensible examination from one that is questioned months later in an audit.
MT, PT or UT for your Memphis job
Choose MT for surface cracking on carbon steel, PT where the metal is not ferromagnetic, and UT where the question is wall thickness or an internal weld flaw. Often the job needs two methods, such as MT on a repair weld after UT shows thinning. Use the three pages for Memphis together when planning scope.
Training your own MT technicians
Plant and shop owners who want their own people qualified can take MT Level 1 and MT Level 2 with us. The employer remains the certifying body under SNT-TC-1A, and the Memphis NDT training page explains how courses connect to your own written practice. The practice tests are a useful self-check before an exam.
Frequently asked questions
Can you perform magnetic particle inspection on welds in Memphis?
Yes. Technicians travel to your shop or plant, examine welds with an AC or DC yoke in two directions, and report indications against the acceptance criteria of the governing code such as ASME or AWS D1.1.
Does magnetic particle testing work on stainless steel?
Austenitic stainless steel is not ferromagnetic, so MT will not work on it. For stainless piping or aluminum structures in Memphis, liquid penetrant testing is the surface method we use instead.
How deep can magnetic particle inspection detect a crack?
MT is a surface method that finds discontinuities open to the surface and a short distance below it. Deeper flaws do not form indications, so volumetric concerns call for ultrasonic testing.
Can MT be done on hot surfaces in Memphis summers?
Wet particles lose mobility on hot steel, so the procedure must be qualified for the temperature or the work scheduled for cooler periods. Dry powder is sometimes better on rough, warm surfaces.
Do you provide fluorescent magnetic particle inspection?
Yes, when a darkened area is available. Fluorescent particles are examined under UV-A light and give the highest sensitivity, so we agree the lighting arrangement and area before mobilizing.
Is demagnetization part of the service?
When residual magnetism could interfere with welding, machining, instruments or rotating service, demagnetization is included in the procedure, and the residual field is checked and recorded in the report.
Does Atlantis have a Memphis office or crew?
No. Atlantis has no office in Memphis. Qualified technicians are mobilized to your site for the agreed scope, so we need site address, access requirements and your preferred code reference at quote stage.
Which standards cover magnetic particle inspection?
ASME Section V Article 7 covers the method for code work, with acceptance in ASME Section VIII, B31.3, AWS D1.1 or D1.5 depending on the asset. ASTM E709 and E1444 are widely referenced.
How do I get my own people qualified in MT?
Our MT Level 1 and Level 2 courses cover theory and practical skills. Your company certifies its own personnel under its written practice, and we can help you draft or review that practice.
Inspection and training around Memphis
- Ultrasonic testing (UT) in Memphis
- Liquid penetrant testing (PT) in Memphis
- Magnetic particle inspection services
MT by industry for Memphis: Rail · Chemical Processing · Pulp & Paper.
MT by job: Magnetic particle weld inspection · Magnetic particle inspection of lifting equipment · Magnetic particle inspection of castings and forgings · Magnetic particle inspection of structural steel and bridges.
Training your own technicians: MT Level 1 training · MT Level 2 training · NDT training for Memphis technicians.
Request an MT inspection quote for Memphis
Send the component and material, the quantity, the code or specification and the site address. We reply within one business day with the scope, the mobilization plan and a quote. Request a quote for magnetic particle inspection in Memphis.
Need magnetic particle testing (MT) done, or learned?
Atlantis provides magnetic particle testing (MT) as an inspection service, trains technicians in it, and lets teams practise it on the Practical NDT simulator.