Ultrasonic Testing (UT) and Thickness Gauging in Memphis, Tennessee
Atlantis NDT mobilizes Level II ultrasonic technicians to Memphis, Tennessee for wall thickness surveys, corrosion monitoring and shear-wave examination of welds. The work typically covers river terminal tanks and piping on President's Island, plant process lines, structural steel and fabricated vessels across the Mid-South. Send us the asset list, the governing code and the access conditions, and we will scope the job around it. Request a UT quote for your Memphis site.
Where ultrasonic testing is used in Memphis
Memphis sits on the Mississippi River, and the Port of Memphis describes a stretch of about fifteen river miles with dozens of waterfront facilities, most of them concentrated on President's Island. The terminals there handle bulk liquids such as petroleum, along with cement, steel, fertilizer and grain. That mix creates a steady need for thickness data: atmospheric storage tanks, transfer piping, loading arms, dock piping and the supports that carry them all lose wall to corrosion under insulation, soil-side attack and splash-zone wetting.
Beyond the river, the city is a rail and highway crossroads, and the region supports food and chemical processing, metal fabrication, power generation and distribution warehousing. Each of those has a different UT question. A fertilizer or chemical line asks how much wall remains at an elbow. A fabrication shop asks whether a groove weld on a crane runway beam has lack of fusion. A warehouse operator asks whether a heavy base plate weld on racking or a dock leveler frame has cracked. The ultrasonic method answers all three, provided the technician matches the technique to the question.
Memphis also lives with large Mississippi crossings and the steel highway structures that feed them. Owners and engineers of that kind of steel use UT mainly to examine welded repair details and to confirm plate thickness where section loss is suspected, working under the owner's bridge or structural code rather than a generic procedure.
What UT finds in Memphis assets, and what it does not
Ultrasonic testing sends sound into the material and listens for what returns. For thickness, the time between the front-surface pulse and the back-wall echo, multiplied by the sound velocity of the material, gives wall thickness. For welds, an angled shear wave travels through the weld volume and reflects from planar flaws such as lack of fusion, incomplete penetration and cracks.
On Memphis carbon steel tanks and pipe, the method is very good at general wall loss and localized pitting, provided the surface is cleaned enough for coupling. It is less reliable where the outer surface is heavily scaled, where the coating is thick and soft, or where the inside surface is so rough that the back-wall echo scatters. Cast iron and coarse-grained cast or centrifugally cast pipe attenuate sound strongly, so readings may be noisy or absent. Austenitic stainless welds also scatter shear waves, and a technique that works on carbon steel may need a different probe and a trial on a mock-up.
UT is not a surface-crack method. A tight surface-breaking crack at a toe may be easier to find with magnetic particle inspection in Memphis on ferromagnetic steel or liquid penetrant testing in Memphis on non-magnetic alloys. A good job plan names which method answers which question.
Codes and acceptance criteria for Memphis UT work
The governing document for a UT job is the construction or in-service code the owner already works under. For fabricated pressure equipment, ASME Section V sets the examination method: Article 4 covers ultrasonic examination of welds, Article 5 covers ultrasonic examination of materials, and Article 23 carries SE-797 for contact pulse-echo thickness measurement. Acceptance is then taken from the code of construction, for example ASME Section VIII Division 1 Appendix 12 for vessel welds or Table 341.3.2 of ASME B31.3 for process piping. Structural steel follows AWS D1.1, which includes ultrasonic acceptance criteria for groove welds, and bridge steel follows AWS D1.5.
In-service equipment is a different regime. API 510, API 570 and API 653 place responsibility for the inspection plan with the owner's authorized inspector. Atlantis does not act as that inspector. We perform the ultrasonic work, report the thickness at each condition monitoring location, and give your inspector the data to calculate corrosion rate and remaining life.
Tennessee requires periodic state inspection of boilers and of unfired pressure vessels above stated size and pressure limits, administered through the Workplace Regulations and Compliance division of the state labor department. Repairs and alterations to that equipment follow the National Board Inspection Code. If a UT finding on a Memphis vessel leads to a repair, the repair plan and its examination requirements come through the owner's chosen inspection channel, not through us.
Where process safety management applies, OSHA 29 CFR 1910.119(j) expects inspection and testing in line with recognized and generally accepted good engineering practice, and thickness records are one of the most common pieces of evidence for it.
How a UT job is done
A thickness survey begins with a grid or a list of condition monitoring locations marked on the equipment. The technician prepares each spot, removes loose scale, applies couplant and calibrates the instrument on a step block of the same material, covering the expected thickness range. A dual-element probe is the usual choice on corroded steel because it handles rough and pitted surfaces better than a single-element probe, and an A-scan display lets the technician see the waveform and avoid doubled or false readings on thin or laminated wall. Hot lines call for high-temperature probes and couplant, with the temperature recorded so a correction can be applied.
Weld examination is a different technique. The technician builds a reference level or distance-amplitude curve from side-drilled holes in a calibration block, selects an angle beam (commonly forty-five, sixty or seventy degrees depending on thickness and weld geometry), and scans from both sides of the weld where access allows. Indications are located, sized against the reference level and evaluated against the acceptance table the code names. Every setup is recorded so another Level II can repeat it. Our ultrasonic testing service page describes the general technique in more detail, and the ultrasonic testing guide covers the physics.
Who performs the work
Technicians who mobilize to Memphis are qualified under Atlantis's written practice, written to ASNT SNT-TC-1A. A Level II sets up the instrument, calibrates, performs the examination and interprets the results against the procedure. An ASNT Level III approves the procedures and reviews the reports. Our founder, Anoop Rayavarapu, is ASNT NDT Level III in UT, RT, MT, PT and VT. Atlantis has no office in Memphis: technicians travel to your site for the agreed scope, which keeps the crew matched to the job rather than to a fixed roster.
If you need a procedure written for a specific code, or want your own written practice reviewed, see our Level III consulting and written practice development pages.
What a Memphis UT report contains
- Component or line number, location and a sketch or isometric reference.
- Procedure number and revision, and the code section it follows.
- Instrument, probe, calibration block, couplant and the calibration check records.
- Technician name and qualification level.
- For thickness: a reading at each location, nominal thickness, minimum required thickness where the owner supplies it, and a thickness grid for area surveys.
- For welds: scan plan, reference level, indication location and length, amplitude, and accept or reject against the named criteria.
The report is written so an owner's inspector, an insurer or an auditor can follow it without a phone call.
Planning a UT job in Memphis
Memphis summers are hot and humid, and steel surfaces in the sun can be hot enough to damage standard couplant and probes. Cold snaps are shorter than in the upper Midwest but do occur, and ice on river terminal ramps changes how access is planned. Humidity also keeps surfaces damp, so surface preparation and drying matter for couplant behavior. Dock and terminal work follows the facility's own access and safety rules, and plants usually require site orientation and badging before work starts, so give us those requirements when you request a quote.
Outage windows matter too. Many process facilities schedule thickness work at turnaround so the equipment is cold, empty and scaffolded, and requests tend to cluster in spring and fall. River levels can affect terminal operations, so we plan around the facility's own operating schedule.
Typical problems a Memphis UT survey is asked to settle
The questions that bring owners to ultrasonic testing along the Mississippi corridor are fairly consistent. A tank owner wants to know whether the shell course nearest the bottom has thinned since the last survey, and whether the annular plate under it is still sound. A pipeline or terminal operator wants thickness at elbows, reducers and dead legs where flow turbulence or stagnant water speeds up corrosion. A fabricator wants evidence that a thick-section groove weld was fused through before it is painted and shipped. An insurer or lender wants a baseline before equipment changes hands.
Each of these calls for a slightly different plan. A bottom-adjacent shell survey needs a tight vertical grid and a decision about how to treat coating. A dead-leg survey needs a wide sweep of the pipe circumference, because the thinnest wall is often at the six o'clock position where water collects. A thick-section weld may need a lower frequency to penetrate and a trial on a calibration block that reflects the actual joint geometry. Agreeing the plan with your engineer before mobilization saves repeat visits, and it also makes the resulting numbers directly comparable to the previous survey.
Records matter as much as readings. If last year's survey used a grid of one hundred locations and this year's uses a different layout, no one can say with confidence whether a thin spot is new. We therefore mark locations, photograph them where permitted, and keep the grid identical to the one on your drawings so that trends can be read directly from the data.
UT, MT or PT for your Memphis job
Use UT when the question is about wall thickness or the inside of a weld. Use MT when the question is surface cracking in carbon or low-alloy steel, and PT when the surface is non-magnetic or the item is non-ferrous. Most real jobs combine two of them: for example thickness gauging at CMLs plus MT at repair welds.
Training your own UT technicians
If you would rather build in-house capability, we offer UT Level 1 and UT Level 2 training, and the UT simulator lets trainees practice scanning before they touch real equipment. Under SNT-TC-1A your company, not the course provider, certifies its own personnel, so see the NDT training for Memphis page for how that works for employers.
Frequently asked questions
Can Atlantis do ultrasonic thickness testing on storage tanks in Memphis?
Yes. Technicians travel to the terminal or plant and take readings at the condition monitoring locations you specify, then report them to your authorized inspector, who calculates corrosion rate and remaining life.
Do you perform ultrasonic weld inspection in Memphis?
Yes. Shear-wave examination of groove welds is done with angle beams against a reference level, and acceptance is taken from the construction code the weld was built under, such as ASME or AWS D1.1.
Does Atlantis have an office in Memphis?
No. Technicians are mobilized to your site for the agreed scope, so the crew is matched to the job. You give us the location, access rules and codes, and we plan the visit around them.
Will Atlantis act as the API 510, 570 or 653 inspector on a Tennessee vessel or tank?
No. Your owner-user authorized inspector remains responsible for the inspection program. Atlantis performs the ultrasonic work and delivers the thickness data and reports your inspector needs.
What surface temperature limits apply to UT thickness readings?
Standard probes and couplants have limits, so hot lines need high-temperature probes and couplant, and the surface temperature is recorded so a velocity correction can be applied. Tell us the operating temperature when you request a quote.
What does UT miss that I should worry about?
UT can miss tight surface-breaking cracks, struggles on heavily scaled or very rough surfaces, and is difficult on cast iron and coarse-grained material. For surface cracks we pair it with magnetic particle or liquid penetrant testing.
What should I send to get a UT quote for a Memphis job?
Send the asset list or drawings, materials, nominal thickness, operating temperature, the governing code, and site access and badging requirements. A short call or email lets us confirm scope and the qualifications you need.
Which codes govern ultrasonic examination on Memphis projects?
ASME Section V Articles 4, 5 and 23 set the method, while acceptance comes from the construction code, such as ASME Section VIII, ASME B31.3 or AWS D1.1. Your contract names the edition.
Can you train our own staff in ultrasonic testing?
Yes. We offer UT Level 1 and Level 2 training with a practice simulator. Under SNT-TC-1A your company certifies its own people against its written practice, and we can help you build that practice.
Inspection and training around Memphis
- Magnetic particle inspection (MT) in Memphis
- Liquid penetrant testing (PT) in Memphis
- Ultrasonic inspection services
UT by industry for Memphis: Rail · Chemical Processing · Pulp & Paper · Food, Beverage & Pharmaceutical.
UT by job: Ultrasonic pipe thickness testing · Ultrasonic weld inspection · Ultrasonic boiler tube thickness testing · Ultrasonic testing of castings and forgings.
Training your own technicians: UT Level 1 training · UT Level 2 training · NDT training for Memphis technicians.
Request an UT inspection quote for Memphis
Send the component and material, the quantity, the code or specification and the site address. We reply within one business day with the scope, the mobilization plan and a quote. Request a quote for ultrasonic testing in Memphis.
Need ultrasonic testing (UT) done, or learned?
Atlantis provides ultrasonic testing (UT) as an inspection service, trains technicians in it, and lets teams practise it on the Practical NDT simulator.