Magnetic Particle Inspection (MT) in Austin, Texas

Atlantis NDT sends Level II technicians to Austin facilities and job sites for magnetic particle inspection of welds, lifting hardware, crane steel and machined parts. MT finds surface and near-surface cracks in ferromagnetic steel, which makes it a fast check on structural welds, lifting lugs and repaired surfaces. State what you need examined and where, then request a magnetic particle inspection quote for Austin.

Where magnetic particle inspection is used in Austin

Austin's economy is more about high-technology construction and manufacturing than refining, and that shapes the steel work. Large chip fabs and data centers are built on structural steel frames with heavy crane loads during erection, and those cranes, rigging lugs and spreader beams are lifted repeatedly. Equipment manufacturers in the region fabricate frames, skids and pressure parts. Power generation equipment, water treatment structures and highway bridge steel round out the list. Every one of those sites has welded carbon or low-alloy steel where the failure mode is a surface crack that starts at a weld toe or a sharp notch.

Typical Austin jobs for MT include weld toes on column splices and bracing connections, padeyes and lifting lugs added for equipment setting, crane runway beams and hook blocks, trailer and truck frame repairs, and weld repairs made after a gouged-out defect. When a structural drawing calls for surface examination of a fillet weld, or a rigging inspector wants proof that a lug weld is crack-free before a heavy lift, magnetic particle testing is usually the quickest answer.

What MT finds, and where it cannot help

Magnetic particle inspection works on ferromagnetic materials only: carbon steel, low-alloy steel and martensitic grades. When the part is magnetized, a crack or other break in the surface interrupts the magnetic field and pulls fine iron particles into a visible line. The method is sensitive to tight surface cracks that a visual examination could miss, and it also reveals some discontinuities just under the surface.

It will not work on austenitic stainless steel, aluminum, copper or titanium, because they do not carry a magnetic field. Austin facilities with stainless process piping need liquid penetrant testing in Austin for those welds instead. MT is also not a depth gauge: it shows that a crack exists and where it runs, not how deep it is, and it cannot find a flaw buried deep in a thick weld. Paint or scale thick enough to keep particles from reaching the metal has to be removed before an examination.

Codes and acceptance criteria

The method itself is governed by ASME Section V, Article 7, with ASTM E709 as the general guide and ASTM E1444 as the practice. Acceptance depends on the construction code: for pressure vessels, ASME Section VIII Division 1 Appendix 6 gives the MT methods and acceptance standards, and for process piping ASME B31.3 sections 344.3 and Table 341.3.2 apply. Structural steel under AWS D1.1 uses its own surface examination provisions, and state highway bridges built under AWS D1.5 follow the bridge code.

In Texas, the Boiler Program at the Texas Department of Licensing and Regulation oversees registered boilers and certifies repair and alteration companies, so MT of a boiler repair weld is reported to the owner and the commissioned inspector. Mechanical integrity programs under OSHA 29 CFR 1910.119(j) also expect recognized and generally accepted good engineering practice. Read our breakdown of Article 7 requirements for the detail behind a procedure.

How the technique is applied

For most Austin field work the technician uses an electromagnetic yoke. The yoke is placed across the weld, the particles are applied, and indications are read and recorded. Under Article 7, an AC yoke must show a minimum lifting power of 10 pounds at the largest pole spacing used, and a DC or permanent-magnet yoke 40 pounds, checked on a test piece before the work begins. The part is examined at least twice, with the field turned roughly 90 degrees between passes, so that cracks running in any direction are crossed by the field.

Dry powder is convenient on rough weld surfaces in warm weather, while wet visible or fluorescent particles are more sensitive on smooth machined parts. Fluorescent work needs a darkened area and a UV-A light with the intensity and ambient-white-light limits the procedure sets, which on a bright Texas jobsite usually means a tent or a covered, shaded work area. Prods can be used for thick sections where a yoke does not reach, but burn marks on the surface make them unsuitable for some finished parts, so the procedure states when they are allowed.

Where residual magnetism could interfere with later welding, machining or a sensitive instrument, the part is demagnetized and checked with a field indicator afterward. Magnetized ferromagnetic structure near arc welding can also deflect the arc, which is another reason to demagnetize.

Who does the work and how it is reviewed

MT technicians who work for Atlantis are qualified under our written practice, which is built on ASNT SNT-TC-1A. A Level II adjusts the equipment, performs the examination and interprets the indications against the code. An ASNT Level III approves the written procedure and the reporting format, giving you a second qualified reviewer on the process. Under SNT-TC-1A the employer issues the certification, so the written practice of the technician's employer is what defines what he or she can sign. If you need a procedure written for your own project or want a Level III to audit a contractor's MT work, see our Level III consulting service and written practice development.

Structural erection and rigging checks around Austin

A large share of Austin MT work comes from construction rather than plant maintenance. When a steel frame goes up for a fab, a data center or an office tower, erectors weld temporary lifting lugs, shear plates and bracing, and some of those welds are ground off afterward. Crane picks of heavy equipment rely on padeyes and spreader beams whose welds the rigging engineer may require to be crack-free. A quick pass with a yoke before the lift gives the rigger documented evidence instead of a visual opinion. For permanent connections, a project specification may list a percentage of fillet welds on moment frames for surface examination, and the technician works from the weld map the special inspector provides.

Weld repairs bring another need. After a defect is excavated by grinding or air-arc gouging, MT confirms the cavity is clear before the repair weld is made, and again after the repair is ground flush. Skipping the first check means welding over a crack tip that was not fully removed, which is a common reason for a repair to fail. The report ties each check to the repair record so the sequence is visible to the inspector.

Telling cracks from look-alikes

A line of collected powder does not always mean a crack. Sharp changes of section, the edge of a weld cap, a scribe mark or a magnetic writing on the steel can hold particles. A trained Level II tells relevant indications from non-relevant ones by looking at shape and position, lightly dressing the area and re-examining, or changing the field direction. A tight crack gives a sharp, crisp line that persists after the particles are blown away and rebuilt, while a magnetic-writing indication fades after demagnetizing and repeats poorly. Rounded indications are evaluated differently from linear ones under most acceptance tables, and the report states which category each falls under.

Surface condition affects what can be seen. A weld left in the as-welded condition with spatter and a rough toe will hold particles that mimic defects, so a light grind or wire-brush of the area is agreed before the examination. Coatings thicker than the procedure permits must be removed, because the field has to reach the steel at full strength.

What the MT report shows

Every report identifies the part or weld by drawing number or tag, the procedure and revision, and the code edition. It records the magnetizing technique, yoke or prod spacing, the lifting power check, the particles and carrier used, the lighting measurements for fluorescent work and the technician's name and level. Each indication is listed with its location, orientation and length, and is marked accepted or rejected against the named criteria. Sketches or photos show the extent of the area examined, and any demagnetization result is noted.

Planning MT work in Austin

Surface temperature is a practical issue in Central Texas. Steel left in summer sun can be too hot for some particle suspensions and for a technician's hand, and when the surface exceeds the range the procedure permits, the work either waits for the part to cool or uses a procedure qualified for the higher temperature. Cold is rarely a limit here, but wet weather and wind can blow dry powder away or ruin a wet bath, so outdoor work is often scheduled for dry mornings and shielded where possible.

Plan for site access: badging, safety orientation, hot work and lift permits, and the clean-area or escort rules at fabs and data centers. Because Atlantis has no office in Austin, technicians are mobilized to your site, so you will want to combine the MT scope with any other inspection so the trip serves the whole job. We reply within one business day to a quote request.

MT, PT or UT for your Austin job

Pick MT for ferromagnetic steel when the target is a surface crack. If the material is stainless or aluminum, or the surface cannot take a magnetic field, choose liquid penetrant in Austin. If you need to know wall thickness or look for a buried flaw, choose ultrasonic testing in Austin. Many repairs get MT on the final weld and ultrasonics on the base metal around it. Our comparison of MT and PT explains the choice in more detail, and the national magnetic particle testing page and MT guide cover the basics.

Training your own MT technicians in Austin

Companies in the Austin area that want in-house capability can start with our MT Level 1 training and MT Level 2 training, then use the Austin NDT training page and practice tests to prepare for the employer's examinations.

Frequently asked questions

What can magnetic particle inspection find on structural steel in Austin?

MT finds surface and slightly subsurface cracks, laps and seams in ferromagnetic steel, such as toe cracks on welds, cracks at lifting lugs and fatigue cracks on crane steel. It does not show depth and will not detect deep buried flaws.

Can MT be used on stainless steel pipe at an Austin fab?

Austenitic stainless does not hold a magnetic field, which rules MT out for it. Liquid penetrant testing is the normal choice for surface cracks in stainless welds, and ultrasonics covers thickness or buried flaws.

Do you perform fluorescent magnetic particle testing outdoors?

Fluorescent particles need a darkened work area and a UV-A light with the intensity the procedure sets. On a sunny jobsite we use a shelter or tent, or choose visible-color particles where the procedure allows them.

Does Atlantis keep a team in Austin for MT work?

No. Atlantis has no office in Austin. Qualified technicians travel to your site for the agreed scope, which is why we ask for the full list of components and access conditions when you request a quote.

Which standard do you use for MT acceptance?

We use the acceptance criteria of the construction code your project names, such as ASME Section VIII Division 1 Appendix 6 or B31.3 for pressure equipment and piping, or AWS D1.1 for structural welds. The procedure cites the edition.

Why does magnetic particle inspection require two directions of magnetization?

Cracks are only revealed when they cross the magnetic field at a good angle. Examining twice, about ninety degrees apart, catches cracks that run in any direction on the surface.

Do parts need to be demagnetized after MT?

Only when residual magnetism could interfere with later welding, machining, instruments or service. When it is required, the technician demagnetizes the part and verifies the field with a meter before reporting.

What do I send to get an MT quote for Austin?

Send the list of components or welds, material grade, surface condition and coating, size range, applicable code and edition, access and permit needs, and preferred timing. A few photos make planning easier.

Can our own technicians learn MT through Atlantis?

Yes. We offer MT Level 1 and Level 2 training aligned to SNT-TC-1A. Your company then qualifies and certifies its technicians under its own written practice after the required experience.

Inspection and training around Austin

MT by industry for Austin: Water & Wastewater Utilities.

MT by job: Magnetic particle weld inspection · Magnetic particle inspection of lifting equipment · Magnetic particle inspection of castings and forgings · Magnetic particle inspection of structural steel and bridges.

Training your own technicians: MT Level 1 training · MT Level 2 training · NDT training for Austin technicians.

Request an MT inspection quote for Austin

Send the component and material, the quantity, the code or specification and the site address. We reply within one business day with the scope, the mobilization plan and a quote. Request a quote for magnetic particle inspection in Austin.

Need magnetic particle testing (MT) done, or learned?

Atlantis provides magnetic particle testing (MT) as an inspection service, trains technicians in it, and lets teams practise it on the Practical NDT simulator.