Magnetic Particle Inspection (MT) in Allentown, Pennsylvania

Atlantis NDT sends Level II technicians to Allentown and the surrounding Lehigh Valley to perform magnetic particle inspection (MPI, also called mag particle testing) on carbon and low-alloy steel welds, castings, forgings, crane components and structural connections. Yoke and prod techniques with dry or wet particles locate surface and near-surface cracks that a visual check can miss. Use the MT quote request for Allentown and tell us the part, the material, the code and how many welds or components are involved.

Where magnetic particle inspection is used in Allentown

Allentown is a region of steel fabrication and heavy handling. Truck cab and chassis assembly in nearby Macungie, machine shops and metal fabricators, and food and beverage plants with large frames and supports all rely on welded carbon steel. The area also carries the memory of Bethlehem Steel, and the people who work in its industrial parks understand that fatigue cracks start at welds and sharp changes of section. Today the largest consumer of steel by footprint is warehousing: the Route 33 and Interstate 78 corridors are lined with distribution buildings whose rooftop frames, loading-dock equipment, forklift masts and overhead cranes see repeated loading.

Typical MT targets in this setting include weld toes on structural frames, lifting lugs and padeyes, crane hooks and hoist structures, truck frame cross members, pressure vessel nozzle welds in carbon steel, support lugs on tanks and receivers, shafts and gears in plant machinery, and hydraulic cylinder components. Because many of these parts cycle in load, the cracks MT is built to find are fatigue cracks, which begin at the surface and grow slowly until a part fails suddenly. Finding them while they are tight and short is the difference between a repair and a replacement.

The region also has an aging stock of industrial buildings and equipment that new owners are putting back into service. A pre-use MT survey of lifting points and structural welds is a straightforward way to establish a baseline before a hoist or a platform returns to work.

What magnetic particle inspection finds and what it misses

MT works because a crack in magnetized ferromagnetic steel disturbs the magnetic field and forms a small leakage field that attracts fine iron particles. The particles gather along the crack and make it visible. It detects surface and slightly subsurface discontinuities in material that can be magnetized: carbon steel and most low-alloy steels. It does not work on austenitic stainless steel, aluminum, copper or other non-magnetic metals, so a stainless fabrication in a dairy or beverage line calls for a different method.

The technique is directional. The field must cross the crack at a favorable angle, so we examine each area twice with the field direction turned roughly ninety degrees, to reveal cracks running in any direction. MT also has depth limits: it is strong on tight surface cracks but weak on buried flaws. Heavy paint, scale or rust reduces sensitivity, and very rough surfaces can hold particles and create false indications that must be sorted into relevant and non-relevant. When the work calls for confirmation of volumetric quality, ultrasonic testing in Allentown complements MT. For a general overview, read our complete guide to magnetic particle testing or visit the national magnetic particle testing page.

Codes and acceptance criteria that apply

MT is performed to a written procedure that follows the construction or service code. ASME Section V Article 7 sets out the method requirements: yoke lifting power, field strength verification, particle types, lighting and examination coverage. Acceptance is then taken from the code that governs the item. For ASME Section VIII Division 1 vessels, Mandatory Appendix 6 contains MT methods and acceptance. ASME B31.3 piping calls for MT under paragraph 344.3 with criteria in Table 341.3.2. Structural steel welded to AWS D1.1 has visual and magnetic particle provisions in its inspection clause, and state bridge steel follows AWS D1.5. ASTM E709 is a guide to MT and ASTM E1444 is the practice covering the method in general industry. Our explainer on ASME Section V Article 7 walks through the main requirements.

The state layer matters for pressure equipment. Pennsylvania's Department of Labor and Industry runs the Boiler Division, which issues operating certificates for boilers and unfired pressure vessels based on inspections by commissioned inspectors. When welding repairs are carried out on a vessel, the National Board Inspection Code governs the repair, and welded repairs are limited to organizations holding an R stamp. MT after repair welding is a routine acceptance step. Atlantis performs the MT and reports the indications; the commissioned inspector and the repair organization remain responsible for their own roles.

Technique: yokes, prods and particles

Most field MT in Allentown is done with a portable electromagnetic yoke, which magnetizes the area between its legs. Under Article 7, an alternating-current yoke must demonstrate a lifting power of at least 10 pounds at the maximum pole spacing used, and a direct-current or permanent-magnet yoke at least 40 pounds. We check the yoke with a test weight before use and on the schedule your procedure sets. Prods can be used for large castings or heavy welds where a yoke cannot reach, but prods carry a risk of arc burns at the contact points, so they are avoided on finished surfaces and heat-sensitive alloys.

Particles come in two broad families. Dry powder is common on rough welds and in hot or outdoor conditions, and suits yoke work in the field. Wet suspension, usually fluorescent, is more sensitive for fine cracks and is the usual choice on machined components or critical welds. Fluorescent examination takes place under UV-A light in a darkened area, so we plan for a shaded setup or an enclosure. Visible-color particles used with a white contrast paint are an alternative where darkness is hard to achieve.

Demagnetization follows when residual magnetism could interfere with later operations. Residual fields can disturb arc welding, attract chips on a machined part or upset bearings and instruments, so the procedure states whether demagnetization is needed and how the field is checked afterward. Parts are cleaned of particles before they return to service.

Fatigue, lifting equipment and why surface cracks matter

Lifting gear deserves its own mention because the consequences of failure are severe. Hooks, shackles, spreader beams, hoist frames and runway girders carry load cycles every shift, and the cracks that grow in them are almost always surface-initiated. Owners of cranes and below-the-hook devices often schedule periodic MT as part of their frequent and periodic inspection routines, with the scope and acceptance written by the responsible engineer. We perform the examination to your procedure, report every indication and leave the decision on removal from service with you.

Surface preparation and indication evaluation

Good results start with clean steel. Oil, grease, loose scale and heavy paint must be removed in the inspection area, and welds left rough may need light grinding. The technician evaluates every indication: a linear indication from a crack, a rounded indication from porosity, and the many non-relevant indications that come from magnetic writing, changes in section or the edge of a weld. Relevant indications are measured and compared against the code's acceptance criteria. Disputed indications may be wiped away and re-tested to confirm whether they reappear.

Coverage, lighting and verification

A magnetic particle examination is only as good as its coverage. The procedure defines overlap between yoke positions, the area examined around each weld, and the lighting at the surface, which for visible particles must be bright enough to see fine lines and for fluorescent work must be matched with low ambient light. Before the job we confirm the particles are performing, using a known reference or a pie-shaped field indicator that shows the field direction in the part. Where a result is doubtful, the area is re-examined rather than accepted on a hunch.

Who performs the inspection

Atlantis has no office in Allentown. Technicians are mobilized to your plant, fabrication shop or yard for the agreed scope. They are qualified under the company's written practice, built on ASNT SNT-TC-1A, in which the employer certifies its own personnel. A Level II sets up the equipment and performs and interprets the examination, and an ASNT Level III approves the procedure and reviews the report. If your owner specification requires different qualification evidence, we discuss it before the quote, not after the work.

What the MT report contains

The report names the component and each examined area, the procedure number and revision, the technique and current or yoke type, the particles and carrier, and the lighting used. It records equipment checks such as yoke lifting power, the technician's name and certification level, the date and the surface condition. Each indication is listed with location, orientation and length, with an accept or reject decision against the named criteria, and sketches or photographs mark where it sits. A clear record of areas examined with no indications is as valuable as the defects, because it proves coverage.

Planning an MT job in Allentown

Weather is the main variable. In cold months, steel temperatures drop and wet suspension carriers become sluggish, so outdoor work such as crane runways and yard structures may need procedures that cover low temperatures or a delay for a milder day. Summer heat can push exposed steel too hot for wet methods, which is where dry powder and shaded setups help. Humidity and rain complicate yard work, so a covered area makes a difference.

Access is a second factor. Overhead cranes, roof frames and elevated platforms need lift equipment or scaffolds and fall protection arranged with your safety lead. Many plants in the industrial parks along Route 33 and Route 100 require orientation and permits before contractors enter. Share your site rules with us early. We coordinate timing with your supervisor and do not promise an arrival window in advance.

MT, PT or UT: choosing the right method in Allentown

For surface cracks in carbon or low-alloy steel, MT is usually the fastest and most sensitive field method. If the part is stainless steel, aluminum or a non-magnetic alloy, use liquid penetrant testing in Allentown instead. When the concern is wall loss or an internal flaw in a weld, choose ultrasonic testing, covered on our Allentown UT page. If you are comparing the two surface methods, our MT versus PT comparison explains where each wins. For Pennsylvania-wide scopes, see inspection services in Pennsylvania.

Training your own MT technicians

Plants that want to build in-house capability can start with MT Level 1 training and move to MT Level 2 training, both led by an ASNT Level III. The training page for Allentown explains how courses reach employers in the Lehigh Valley, and the SNT-TC-1A eligibility checker shows the experience and hours your technicians will need under your written practice.

Frequently asked questions

What materials can be inspected with magnetic particle testing?

MT works only on ferromagnetic materials such as carbon steel and most low-alloy steels. Austenitic stainless steel, aluminum and copper cannot be magnetized, so those parts need liquid penetrant testing or another method instead.

What kinds of defects does magnetic particle inspection detect in Allentown steel structures?

It finds surface and slightly subsurface cracks, laps, seams and lack of fusion at weld toes and edges. Fatigue cracks at crane lugs, frame welds and shafts are common targets because they start at the surface.

Why do you test each area in two directions?

A crack is detected best when the magnetic field crosses it at a right angle. Examining each area twice with the field turned about ninety degrees ensures cracks running in any direction produce a visible indication.

Should we use dry powder or wet fluorescent particles?

Dry powder suits rough welds, outdoor work and hot surfaces. Wet fluorescent suspension is more sensitive for fine cracks on machined or critical parts, but needs a darkened area for the UV-A examination. We choose based on your procedure and site.

Is demagnetization required after MT?

Only when residual magnetism could interfere with welding, machining, bearings or instruments. The written procedure states the requirement, and we check the remaining field afterward when demagnetization is called for.

Can MT be done through paint or coating?

Thin, tightly bonded coatings may be acceptable if the procedure is qualified for them, but heavy paint, scale and rust reduce sensitivity. We discuss coating thickness and condition when you request a quote and remove coating where required.

How do I request MT inspection for a plant near Allentown?

Send the component or weld type, material, governing code, quantity, access conditions and any site safety requirements through the quote form. Atlantis mobilizes technicians to your site for the agreed scope, and we reply within one business day.

Are your MT technicians certified by Atlantis to work under my company's rules?

Atlantis qualifies its technicians under its written practice based on ASNT SNT-TC-1A, where the employer certifies. If your owner specification names different requirements, tell us up front so we can confirm what documentation you need.

Can your team train our employees to do MT themselves?

Yes. We offer MT Level 1 and Level 2 training with an ASNT Level III instructor, and our Level III consulting can help you write the procedures and written practice your company will use to qualify its own technicians.

Inspection and training around Allentown

MT by job: Magnetic particle weld inspection · Magnetic particle inspection of lifting equipment · Magnetic particle inspection of castings and forgings · Magnetic particle inspection of structural steel and bridges.

Training your own technicians: MT Level 1 training · MT Level 2 training · NDT training for Allentown technicians.

Request an MT inspection quote for Allentown

Send the component and material, the quantity, the code or specification and the site address. We reply within one business day with the scope, the mobilization plan and a quote. Request a quote for magnetic particle inspection in Allentown.

Need magnetic particle testing (MT) done, or learned?

Atlantis provides magnetic particle testing (MT) as an inspection service, trains technicians in it, and lets teams practise it on the Practical NDT simulator.