Ultrasonic Testing (UT) and Thickness Gauging in Allentown, Pennsylvania
Atlantis NDT mobilizes Level II ultrasonic technicians to Allentown and the wider Lehigh Valley for wall-thickness surveys, corrosion mapping by manual scanning, and shear-wave examination of welds on pressure equipment, storage tanks, process piping and structural steel. The work is done at your plant, fabrication shop or yard, under a written procedure approved by an ASNT Level III. To scope a job, use the UT quote request for Allentown and tell us the component, material, nominal thickness and the code that governs it.
Where ultrasonic testing is used in Allentown
Allentown sits in a valley whose economy changed shape within one generation. The riverside steel mills that once defined the area are gone, and the former Bethlehem Steel site is now an industrial park and an arts district built around preserved blast furnaces. What replaced the mills is wider than most people expect: truck and cab assembly in Macungie, food and beverage plants along Route 100, pharmaceutical and diagnostic manufacturing, industrial gas and chemical companies, and an enormous volume of warehousing and distribution space along the Route 33 and Interstate 78 corridors. Each of these puts steel in service that eventually needs a thickness reading or a weld examination.
In practical terms, ultrasonic work in the Lehigh Valley falls into a handful of families. Food and beverage plants run steam headers, hot-water loops, ammonia refrigeration receivers and stainless process vessels, and the carbon-steel parts of those systems lose wall to corrosion under insulation and to condensate attack in low points. Industrial gas and chemical sites operate pressure vessels, storage tanks and piping whose inspection plans call for thickness data at fixed condition monitoring locations. Manufacturing plants that fabricate frames, cabs and chassis components weld heavy plate and tube and need volumetric confidence in structural joints. Distribution centers have a quieter need: sprinkler risers, fire-pump piping, compressed-air receivers and the large steel racking and canopy structures that carry building loads.
Older infrastructure matters as well. The Lehigh Valley has a long history of rail, canal and heavy industry, and many facilities reuse tanks, supports and piping that were installed decades ago. When an owner buys or reactivates such a site, an ultrasonic survey is often the fastest way to learn how much steel is left before engineering decides what to repair, derate or replace.
What ultrasonic testing finds, and what it cannot
Ultrasonic testing sends a sound pulse into a material and times the echo. Two jobs dominate. The first is thickness measurement: the instrument converts the time between the front surface and the back wall into remaining wall, which is what corrosion programs track. The second is weld examination with an angle-beam shear wave probe, which finds planar discontinuities such as lack of fusion, cracks and slag lines that sit inside the weld volume where surface methods cannot reach.
The limits are as important as the capabilities. Sound needs a coupled, reasonably smooth surface, so heavy scale, flaking paint and rough weld caps must be dressed before a trustworthy reading is possible. Coarse-grained castings and austenitic stainless welds scatter and attenuate the beam, which can hide small reflectors and produce misleading noise. Very thin wall and severe pitting are another trap: a probe that sits on the edge of a pit can read the pit floor or a false doubled echo. The technician manages these risks with dual-element probes for corroded surfaces, an A-scan display that lets the operator see the echo pattern instead of trusting a digital number alone, and calibration on a reference block of the same material and similar thickness.
Orientation also matters. A shear-wave beam finds a flaw best when the flaw faces the beam, so a crack running along the weld may need scans from both sides and in more than one skew direction. Where access limits a scan, the report must say so rather than imply full coverage. Our national ultrasonic testing page explains the method in general; this page applies it to Allentown work.
Codes and acceptance criteria used in Pennsylvania
The code decides how a weld is examined and when an indication is rejected, so we ask for it at the start. For pressure vessels built to ASME Section VIII Division 1, ultrasonic weld examination follows Mandatory Appendix 12, and acceptance of flaws is written there. For process piping under ASME B31.3, ultrasonic examination of welds follows paragraph 344.6 with criteria in Table 341.3.2. Underlying both is ASME Section V: Article 4 governs ultrasonic examination of welds, Article 5 covers materials, and Article 23 carries the contact pulse-echo thickness practice used on corrosion surveys. Structural groove welds under AWS D1.1 have their own ultrasonic acceptance rules, and state transportation steel is examined to AWS D1.5.
In service, the picture changes. Inspection of vessels, piping and tanks in operating plants follows the owner's inspection program, often built on API 510, API 570 and API 653. Under those codes the owner's authorized inspector is responsible for the inspection and the integrity decision. Atlantis does not act as that inspector; we perform the ultrasonic examination, record the data and hand it to the inspector. Thickness practice also references ASTM E797 for contact measurement. For a plain-language primer, see our guide to ASME Section V Article 5 thickness measurement requirements.
Pennsylvania has its own regime for pressure equipment. The Department of Labor and Industry's Boiler Division administers the state's boiler and unfired pressure vessel rules, and periodic inspections are performed by inspectors who hold a Pennsylvania commission, either state staff or insurance company inspectors. According to the department's published summary, unfired pressure vessels are inspected at 36-month intervals, a certificate of operation is issued from the inspector's report, and repairs or alterations follow the National Board Inspection Code, with welded repair work limited to organizations that hold an R stamp. Our thickness and weld data feeds into those programs; it does not replace the commissioned inspector's role.
How the work is done: thickness surveys
A thickness survey starts with a map. The owner or inspector marks condition monitoring locations on a drawing or isometric, and we read the same spots each cycle so the corrosion rate is meaningful. The technician prepares each spot by removing loose scale and paint, applies couplant, and calibrates the instrument on a step block made of the same material across the expected thickness range. On corroded carbon steel a dual-element probe is the usual choice because it separates transmit and receive paths and copes better with rough, pitted metal. The A-scan is watched, not just the number, so a doubled echo or a lamination reading is recognized as such.
Hot service needs extra care. Steam lines and hot process piping change sound velocity with temperature, so readings are corrected, and high-temperature probes and couplant are used where the surface is too hot for standard materials. The report records surface temperature so the engineer can interpret the figures. For tanks, readings are commonly taken on a grid on shell courses and at the bottom edge, and each reading is logged against its grid cell. When a location reads below an alarm level the technician flags it immediately to the inspector, so a follow-up scan can define the extent of metal loss before anyone leaves the area.
How the work is done: ultrasonic weld examination
Weld examination uses angle-beam probes, typically 45, 60 and 70 degrees, chosen to suit thickness and joint geometry. A reference level or distance-amplitude curve is built from side-drilled holes in a calibration block, and indications are measured against it. The technician scans along and across the weld from the accessible sides, records the position, length and amplitude of anything that exceeds the recording level, and evaluates it against the construction code. Because shear-wave work depends on interpretation, it is performed only by a qualified Level II or above, and the written procedure is approved by the Level III before the job starts.
Surface condition on the weld cap and adjacent base metal decides whether scans can be completed. Welds left with high crowns or spatter may need grinding. When welds are in the field, such as erected tank shells or structural joints, we plan access, lighting and scaffolding with your supervisor so the scan is complete and safe.
Who does the work and how they are qualified
Atlantis has no office in Allentown. Technicians are mobilized to your site for the agreed scope, and travel to your plant, shop or yard. They are qualified under the company's written practice, which is built on ASNT SNT-TC-1A. In that scheme the employer certifies its own personnel: a Level II sets up and calibrates equipment, performs the examination and interprets results, and an ASNT Level III establishes techniques, approves procedures and reviews reports. Certification of your own staff remains your decision as the employer, and our qualification does not replace a site's own requirements; if your contract needs specific qualification wording, tell us when you request the quote.
What the ultrasonic report contains
A usable report lets an engineer or inspector reproduce the job. Ours identifies the component and the location of each reading, the procedure number and revision, the instrument, probe and calibration block used, the technician and certification level, and the surface temperature where relevant. For thickness work the report presents a table or a grid of readings against nominal and minimum required wall. For welds it lists each indication with position, length, depth and amplitude relative to the reference level, followed by a clear accept or reject against the named criteria, with sketches to show where the indication sits. Data is delivered in the format your inspection database expects wherever possible.
Planning an ultrasonic job in Allentown
Lehigh Valley weather shapes the schedule. Winters bring freezing surfaces that thicken couplant, slow instrument displays and complicate calibration, so outdoor tanks and yard piping may call for heated couplant or waiting for a milder window. Summer sun can push exposed steel above the comfortable limit for standard probes, which is where high-temperature probes and cooling breaks come in. Outages at manufacturing sites usually follow production calendars, so early planning avoids a collision with other contractors working the same shutdown.
Logistics also vary. Plants along Route 100 and the industrial parks off Route 33 often require site-specific safety orientation, badging and permits before technicians can enter, so give us your requirements early. Interstate 78 makes travel straightforward, but heavy truck traffic around distribution hubs can affect arrival planning; we agree timing with your supervisor rather than promising an arrival window. Tell us whether the equipment is in service, and whether hot work or confined-space entry is involved, because both change how a scan is staged.
UT, MT or PT: choosing the right method in Allentown
Ultrasonic testing answers volume and wall questions: how thick is the steel and is there a planar flaw inside the weld. It is the right tool for corrosion surveys and for welds where internal fusion matters. If your question is whether a weld toe or a fillet has a surface crack in carbon steel, magnetic particle inspection in Allentown is faster and more sensitive to surface breaking cracks. If the material is stainless steel or aluminum, liquid penetrant testing in Allentown detects surface-breaking flaws on non-magnetic metals. Many jobs combine methods: UT to confirm remaining wall after a leak, then PT or MT to confirm that a repair weld is free of surface defects. For state-level context see our Pennsylvania inspection services page.
Training your own ultrasonic technicians
Some Allentown plants prefer to build in-house capability. Atlantis offers UT Level 1 training and UT Level 2 training with a Level III instructor, practice on the ultrasonic testing simulator, and a path to qualification under your own written practice. See the NDT training page for Allentown for how delivery works for employers in the Lehigh Valley. If you need a written practice or procedures drafted first, our Level III consulting can help.
Frequently asked questions
What does ultrasonic thickness testing involve at an Allentown plant?
A technician cleans selected spots, applies couplant, calibrates on a step block of matching material and reads remaining wall at marked condition monitoring locations. Results are logged against nominal and minimum thickness so your inspector can track corrosion rate over time.
Can you examine welds ultrasonically as well as measure thickness?
Yes. Level II technicians use angle-beam shear wave probes and a reference curve to examine groove welds for lack of fusion, cracks and slag, then evaluate indications against the construction code you name, such as ASME Section VIII, B31.3 or AWS D1.1.
Do you inspect the vessels and tanks on behalf of the state of Pennsylvania?
No. Pennsylvania boiler and unfired pressure vessel inspections are carried out by commissioned inspectors under the Department of Labor and Industry's rules. We perform the ultrasonic examination and give your inspector the data to use in their own work.
Does ultrasonic testing work on stainless steel and cast parts?
It can, but coarse grain and austenitic weld structure scatter the sound beam, so sensitivity and reliability drop. We discuss the material up front and may propose reference blocks of the same alloy or a different method if the part is a poor candidate.
How should surfaces be prepared before ultrasonic inspection?
Remove loose scale, flaking paint and weld spatter at the inspection spots, and grind high weld caps where angle-beam scanning is planned. A smooth, clean surface lets couplant transmit sound reliably and prevents false or unreadable echoes.
What information do you need to quote an ultrasonic job in the Lehigh Valley?
Send the component type, material, nominal thickness, governing code, approximate number of locations or weld length, access conditions, and whether equipment is in service. Add site safety requirements so we plan the mobilization properly. We reply within one business day.
Who qualifies your ultrasonic technicians?
Technicians are qualified under Atlantis's written practice, built on ASNT SNT-TC-1A. Level II personnel perform and interpret the examination, and an ASNT Level III approves the procedure and reviews reports. If your contract specifies other qualification wording, tell us before the job.
Can ultrasonic testing replace radiography on a weld?
That depends on the construction code and the owner's agreement. Some codes include ultrasonic provisions for production welds, but the substitution must be agreed with the owner, the engineer and the authorized inspector before work starts.
Can you train our maintenance staff in ultrasonic thickness gauging?
Yes. We offer UT Level 1 and Level 2 courses and simulator practice, and can help you set up the written practice under which your employer qualifies and certifies its own technicians following SNT-TC-1A.
Inspection and training around Allentown
- Magnetic particle inspection (MT) in Allentown
- Liquid penetrant testing (PT) in Allentown
- Ultrasonic inspection services
- NDT inspection services in Pennsylvania
UT by job: Ultrasonic pipe thickness testing · Ultrasonic weld inspection · Ultrasonic boiler tube thickness testing · Ultrasonic testing of castings and forgings.
Training your own technicians: UT Level 1 training · UT Level 2 training · NDT training for Allentown technicians.
Request an UT inspection quote for Allentown
Send the component and material, the quantity, the code or specification and the site address. We reply within one business day with the scope, the mobilization plan and a quote. Request a quote for ultrasonic testing in Allentown.
Need ultrasonic testing (UT) done, or learned?
Atlantis provides ultrasonic testing (UT) as an inspection service, trains technicians in it, and lets teams practise it on the Practical NDT simulator.