Ultrasonic Testing (UT) and Thickness Inspection in Savannah, Georgia
Atlantis NDT performs ultrasonic testing in Savannah, Georgia: wall-thickness surveys on corroded piping, vessels, tanks and crane structure, and angle-beam examination of groove welds in carbon steel. The work serves container-terminal equipment, paper and chemical process plants, shipyard and marine steel, and fabrication shops around Chatham County and the Savannah River corridor. Technicians travel to your site for the agreed scope. Send your component list through the UT inspection quote form and we reply within one business day.
Where ultrasonic testing is used in Savannah
Savannah is a working port city first. Garden City Terminal is the largest single-terminal container facility in the Western Hemisphere by acreage, with dozens of ship-to-shore cranes and well over two hundred rubber-tired gantry cranes moving boxes between ships, stacks, trucks and rail. Behind the terminals sit paper mills, sugar refining on the river, bulk and liquid storage, and a growing aerospace and automotive supply base. Each of these has steel that loses wall to corrosion or carries welds that have to be proven sound.
- Terminal equipment: crane boom and portal-leg plate, spreader frames, and the structural welds on gantry rails and runway supports, where thickness loss from salt air and cracks from cyclic loading both matter.
- Paper and pulp mills: steam and condensate piping, digester and recovery-area vessels, dryer-section headers, process water lines and stainless equipment that sees hot, wet, chemically aggressive service.
- Bulk, liquid and food-process storage: atmospheric tank shells and floors, sugar and syrup tanks, fuel storage near the harbor, and the pipe racks that connect them.
- Marine and shipyard steel: hull plate and deck structure on vessels visiting for repair, ballast tank boundaries, pilings, dock fittings and fender supports.
- Aerospace and industrial support: ground-support equipment, hangar structure, jacks and fabricated tooling for the business-jet manufacturing and service cluster around the city's airports.
The common thread is carbon steel in a humid, salt-laden climate. Ultrasonic testing reads the metal that is left, so an owner can decide whether to run, repair or replace.
What ultrasonic testing finds and what it misses
A transducer sends a short sound pulse into the steel, and the instrument times the echo from the back wall or from a reflector inside the metal. Because sound velocity in steel is known, time converts to distance. That makes UT the working method for thickness measurement and for volumetric examination of welds, because it sees inside the section rather than only at the surface.
- It finds: general wall loss, pitting depth under a reading, laminations in plate, internal corrosion on the far side of a pipe, and in welds lack of fusion, incomplete penetration, cracks and slag lines that sit away from the surface.
- It can miss or misread: shallow surface cracks lying in the dead zone just under the probe, flaws oriented parallel to the beam, discontinuities hidden by rough scale or heavy coating, and anything in coarse-grained cast or austenitic material where sound scatters.
- It needs: an accessible, reasonably smooth surface, couplant between probe and metal, a calibration block with a known thickness, and a technician who understands what the screen is showing.
Where the question is surface cracking on a ferromagnetic weld, magnetic particle inspection in Savannah is the sharper tool. UT answers the question of what is inside and how thick it is.
How a thickness survey is carried out
A corrosion survey starts with a list of condition monitoring locations, often shortened to CMLs, and a grid or point map for each component. At each point the technician cleans a patch of surface, applies couplant and takes a reading with a dual-element probe. Dual-element probes keep separate transmitting and receiving crystals, which is why they cope with pitted, rough or lightly corroded outside surfaces better than a single-crystal probe.
- Calibrate on a step block of the same material and across the range of thickness expected, with the temperature of the block close to the temperature of the part.
- Verify on the block again after the work and at any change of probe, cable or instrument.
- Read with the A-scan visible. Watching the waveform, not only the digital number, is how a technician spots a double-echo error on thin wall or a reading dropping into a pit.
- Record the lowest valid reading and the position, and compare against the previous survey, the nominal wall and the minimum required thickness.
Hot piping is common at the mills. High-temperature probes and couplant exist for that service, and readings are corrected for the temperature of the metal. The method is covered in ASTM E797 and in ASME Section V thickness measurement requirements; the owner's inspection program decides how often each location is read.
Ultrasonic examination of welds
For groove welds, the technician uses an angle-beam shear-wave probe, normally 45, 60 or 70 degrees, so the beam crosses the weld at an angle that suits likely flaw orientation. A reference level, or distance-amplitude curve, is built from side-drilled holes in a calibration block so that indication amplitude can be judged against the code. The technician scans the weld from both sides where access allows, moves the probe in a pattern that covers the full volume and the heat-affected zone, and evaluates every indication that crosses the recording level.
This is the work behind structural steel for terminal buildings and crane runways, pressure piping and vessel nozzle welds, and heavy plate repair. Acceptance depends on the governing code, and the code your owner or engineer names decides the method of examination in the first place.
Codes and acceptance criteria for Savannah work
The code on your drawing or in your contract is the rule we apply. For ultrasonic work in this region that usually means one of the following.
- ASME Section V: Article 4 for ultrasonic examination of welds, Article 5 for materials, and Article 23 for thickness measurement practice such as SE-797.
- AWS D1.1: structural welding code for steel, including ultrasonic examination of groove welds and its own acceptance and rejection tables.
- ASME B31.3 and B31.1: process piping at chemical plants and power piping at mills, with examination types and acceptance in the piping code tables.
- ASME Section VIII Division 1: Appendix 12 covers ultrasonic examination of welds in pressure vessels.
- API 510, 570 and 653: the in-service inspection codes for vessels, piping and aboveground tanks. Your authorized inspector holds responsibility for the inspection; Atlantis supplies the thickness data and weld examination results that inspector uses.
OSHA 29 CFR 1910.119 requires covered process facilities to inspect and test equipment under recognized and generally accepted good engineering practice, which is one reason plants keep a documented thickness history.
Georgia boiler and pressure vessel rules
In Georgia the Office of Insurance and Safety Fire Commissioner, through its Engineering Division, inspects boilers and pressure vessels, and its rules sit in Chapter 120-3-26 of the state regulations. Equipment that falls under the program must be inspected regularly, subject to the exemptions the law lists, and accidents are reported to the office immediately by phone with a written report to follow. Thickness readings and weld examinations feed that regime by giving the owner and the commissioner's inspectors dependable data about the shell, heads and nozzles. We do not replace the state or the owner's authorized inspector; we supply measured, documented NDE results they can rely on.
Who does the work in Savannah
Atlantis has no office in Savannah. Technicians are mobilized to your terminal, mill, shop or yard from outside the city for the agreed scope. They are qualified under Atlantis's written practice, which is based on ASNT SNT-TC-1A: Level II technicians set up, calibrate, perform and interpret the examination, and an ASNT Level III approves the procedures and reviews reports. The company's founder, Anoop Rayavarapu, holds ASNT NDT Level III in UT, RT, MT, PT and VT. Atlantis is certified to ISO 9001 and ISO 14001. Procedures are written to your code, so the acceptance criteria are not invented on the day.
What the ultrasonic report contains
- Component identification, location, material, nominal and minimum required thickness.
- The procedure and revision used, the code and edition, and the acceptance criteria applied.
- Instrument, probe, cable and calibration block identification, with calibration checks recorded.
- Technician name and qualification level, and the examination date and surface temperature.
- Thickness grids or point tables with the lowest reading flagged, or for welds, indication position, length, amplitude, depth and accept or reject.
- Sketches or isometric markups so the next survey reads the same locations.
The format is built so an authorized inspector, an engineer or an auditor can follow the result back to a calibrated reading without a phone call.
Planning an ultrasonic job in Savannah
Savannah's climate and access conditions shape the schedule more than most buyers expect.
- Salt air and humidity: outside surfaces rust quickly after wire brushing, so surface prep should be timed close to the reading, and dew on steel at dawn can affect couplant and cleanliness.
- Summer heat: surfaces in direct sun get hot enough to affect probes and couplant, and work in shaded or cooler hours protects both people and data.
- Terminal and port access: secure areas typically require a TWIC card and a site safety orientation, and crane or yard operations dictate when equipment can be taken out of service.
- Mill outages: piping and vessel work clusters into shutdown windows, so thickness data has to be ready before the repair scope is frozen.
- Tides and river traffic: work on dock structure and vessel plate follows the schedule of the berth.
Tell us the component list, access method and outage dates when you ask for a quote. We plan mobilization around those dates rather than promising a crew arrival time up front.
Choosing between UT, MT and PT in Savannah
Match the method to the question. Use ultrasonic testing to size wall loss and to examine the inside of welds. Use magnetic particle testing to find surface and near-surface cracks in ferromagnetic steel, for example the toes of crane welds. Use liquid penetrant testing for surface-breaking flaws on stainless steel, aluminum and other non-magnetic metals. Many jobs need two methods, because a thickness survey and a crack check answer different questions. For background on the method itself, read the UT service overview or the ultrasonic testing guide.
Training your own ultrasonic technicians
If you would rather build a Savannah team than buy visits, Atlantis offers UT Level 1 training and UT Level 2 training under SNT-TC-1A, with the UT practical simulator for hands-on repetition. Under that scheme your company certifies its own people through its written practice; see NDT training for Savannah employers and the SNT-TC-1A eligibility checker. An in-house Level II also reads your thickness data between our visits.
Frequently asked questions
What does ultrasonic thickness testing measure in Savannah plants and terminals?
It measures the remaining wall of steel by timing a sound echo through the metal. In Savannah that means piping at mills, tank shells, crane plate, hull and dock steel, so the owner can compare readings against minimum required thickness.
Can Atlantis do UT inspection of welds as well as thickness?
Yes. Technicians use angle-beam shear-wave probes calibrated on a reference block, scan the weld volume and heat-affected zone, and judge indications against the code named in your contract, such as AWS D1.1 or ASME Section V.
Does Atlantis have an office or lab in Savannah?
No. Atlantis has no office in Savannah. Technicians are mobilized to your terminal, mill, shop or yard for the agreed scope, and you receive a written report that traces every reading to a calibrated instrument.
Can ultrasonic testing be done on hot piping?
Often yes. High-temperature probes and couplant are made for hot lines, and readings are corrected for metal temperature. The practical limit depends on the line temperature, access and the probe in use, so tell us the service conditions when you request a quote.
Who is responsible for an API 510, 570 or 653 inspection when Atlantis does the UT?
The owner's authorized inspector remains responsible for the inspection and the fitness decision. Atlantis performs the ultrasonic examination and thickness survey and gives that inspector complete, documented data to evaluate.
What surface preparation does UT need on coated or rusted steel?
The probe needs a clean contact patch, so loose scale, flaking paint and heavy rust are removed at each reading point. Thin, sound coating can sometimes be read through, but the procedure decides, and the owner approves any coating removal.
Which Georgia agency regulates boilers and pressure vessels?
The Office of Insurance and Safety Fire Commissioner, through its Engineering Division, inspects boilers and pressure vessels in Georgia. Atlantis does not replace those inspections; we provide NDE data that the owner and inspectors can rely on.
When should I choose magnetic particle testing instead of UT in Savannah?
Choose magnetic particle testing when the question is a surface or near-surface crack in ferromagnetic steel, such as a crane weld toe. Choose UT when you need remaining wall or want to examine the inside of a weld.
Can my own technicians learn UT through Atlantis?
Yes. Atlantis teaches UT Level 1 and Level 2 under ASNT SNT-TC-1A recommended practice. Your company then qualifies and certifies its technicians under its own written practice, and the course supports that employer-based process.
Inspection and training around Savannah
- Magnetic particle inspection (MT) in Savannah
- Liquid penetrant testing (PT) in Savannah
- Ultrasonic inspection services
UT by industry for Savannah: LNG · Aviation & Aerospace · Pulp & Paper.
UT by job: Ultrasonic pipe thickness testing · Ultrasonic weld inspection · Ultrasonic boiler tube thickness testing · Ultrasonic testing of castings and forgings.
Training your own technicians: UT Level 1 training · UT Level 2 training · NDT training for Savannah technicians.
Request an UT inspection quote for Savannah
Send the component and material, the quantity, the code or specification and the site address. We reply within one business day with the scope, the mobilization plan and a quote. Request a quote for ultrasonic testing in Savannah.
Need ultrasonic testing (UT) done, or learned?
Atlantis provides ultrasonic testing (UT) as an inspection service, trains technicians in it, and lets teams practise it on the Practical NDT simulator.