Ultrasonic Testing (UT) Inspection in San Francisco, California
Atlantis NDT performs ultrasonic testing in San Francisco on steel that is hard to open up and expensive to get wrong: welded frames in high-rise buildings, pier and shipyard steel along the bay, bridge members, and process piping that serves the wider Bay Area. The service covers wall-thickness surveys and angle-beam examination of welds, with a written procedure and a report built for engineers and building officials. Tell us the member, material and governing document and we reply within one business day.
Why San Francisco steel gets ultrasonic examination
San Francisco is a dense, seismic, waterfront city, and each of those facts shapes what gets inspected. Dense means tall buildings on tight lots, with steel frames fabricated elsewhere and welded or bolted in the street. Seismic means that the welds that tie beams to columns are designed to deform without fracturing, so a hidden lack of fusion matters more here than in a quiet region. Waterfront means piers, seawalls, ferry terminals and a ship repair yard at Pier 70, where two drydocks, the larger rated to lift tens of thousands of tons, service everything from tugs to cruise ships and naval cargo vessels.
The city also depends on large steel structures that cannot be taken out of service lightly. Bridges across the bay and the Golden Gate, elevated transit structures, the cable and rail systems of Muni and regional rail, and the steel that holds up the airport's facilities all go through periodic examination. The 2013 reopening of the new Bay Bridge east span, and the public attention that followed on fasteners and welds, is a reminder that owners of big steel are expected to keep good records.
Beyond city limits, the Bay Area's refining and chemical complex sits along the Carquinez Strait and the Richmond shoreline. That work is a drive away, but it is part of the same inspection market: piping and vessel thickness programs that serve those plants are planned and mobilized from outside the region.
What ultrasonic testing reveals and where it stops
The probe sends a short pulse of sound into the steel through a couplant. The time for an echo to return from the far surface, combined with the speed of sound in that steel, gives thickness. For welds, a probe set at an angle sends a shear wave through the joint; flat flaws such as lack of fusion, incomplete penetration and cracks reflect that beam back toward the probe, and the instrument shows the reflection as a peak on its display.
The method has boundaries. It reads what the beam meets, so very rough or flaking surfaces give poor coupling and unreliable readings. Pitting that is narrower than the probe may be missed between readings. Steel with a coarse cast structure, and austenitic stainless welds, scatter sound and call for a modified technique. Steel with laminations can return an echo from the lamination rather than from the far wall. None of these stops a competent examination, but each is stated in the procedure so that the report does not overclaim.
Water on the surface is a San Francisco-specific wrinkle: fog and spray can leave films of moisture and salt on steel, which affect coupling and corrode blocks and cables. Surfaces are wiped dry and re-coupled, and equipment is cleaned and checked after each use.
Wall-thickness gauging for piping, tanks and marine steel
Thickness work follows a simple discipline: define the locations, read them the same way each time, and compare. Technicians use dual-element probes on corroded surfaces, calibrate on a step block of matching material that spans the expected wall range, and read the A-scan so a doubled echo or a lamination does not slip through as a clean number. High-temperature probes and couplants are available for hot lines. ASTM E797 is the contact thickness practice, and ASME Section V Article 23 contains SE-797 for code work; our overview of thickness-measurement requirements shows how the standards connect.
On waterfront steel, the points of interest are splash zones, tidal ranges and under-pier cross-bracing, where wall loss can be uneven and where access may require boats, lifts or rope-free platforms arranged by the owner. At the shipyard, steel renewal estimates on a hull or tank often depend on a grid of readings taken before docking, which lets the owner estimate the steel to be replaced. Note that Atlantis is still in the process of obtaining UR Z17 approval from DNV, Lloyd's Register and ABS for ship thickness measurement, so readings taken for a vessel are for the owner's own decisions, not for class credit.
For regulated process equipment, the owner's authorized inspector remains the inspector of record under API 510, 570 and 653, and Atlantis provides the thickness data.
Weld examination in structural and bridge steel
Building steel in San Francisco comes under the city's special inspection regime. The city's form for special inspection puts most structural welding, other than certain single-pass fillet welds and decking items, in the category that calls for continuous visual inspection and nondestructive testing, with a fillet-weld exception. The special inspector is employed by the owner or by the engineer or architect of record, and the inspector's name is given to the Department of Building Inspection's district inspector before work begins. Atlantis can perform ultrasonic examination of groove welds as ordered by the engineer, but the special inspector and the engineer of record keep their own roles.
The governing document for building steel is typically AWS D1.1, with AWS D1.8 for seismic force-resisting systems, and the structural drawings and specification say which weld joints need volumetric examination and what acceptance class applies. Bridge work is under AWS D1.5, and the contract documents set the examination scope. On state bridge work, the contractor's welding quality control plan and the owner's quality assurance program decide who does what; Atlantis works to the procedure and acceptance criteria in the contract and does not replace the contractor's quality control manager.
Technique is the same angle-beam practice used anywhere: 45, 60 or 70 degree probes selected by joint geometry, a reference level built from side-drilled holes, scanning from both sides where access allows, and indications recorded by location and size against the code's criteria.
Records for engineers and building officials
A building official or a structural engineer reading a UT report wants to find a particular connection quickly. Reports for building frames therefore reference gridlines, floor levels and connection marks, and they carry the detail drawing number so the weld in the report is the weld in the model. Where the engineer has specified a sampling rate or a re-test rule after a rejected weld, the report states how that rule was applied, so the next reader does not have to guess.
Photographs of the prepared surface and of the scan layout are attached where they help, because a scan plan on a crowded connection is easier to audit from a picture than from a paragraph. Calibration checks are logged at the start and end of the shift and after any change of probe, cable or instrument settings, and any drift beyond the procedure's tolerance triggers a re-scan of the welds examined since the last good check.
Personnel, procedure and oversight
Technicians work under the company's written practice, which follows ASNT SNT-TC-1A. Level II technicians perform and interpret examinations. An ASNT NDT Level III approves procedures and reviews reports; that role is held in the company by Anoop Rayavarapu, ASNT NDT Level III in UT, RT, MT, PT and VT. Under SNT-TC-1A the employer certifies, so qualification records for each technician are held by the employer and available for review.
Atlantis holds ISO 9001 and ISO 14001 certificates for its management systems. Those do not substitute for a procedure, calibration check or personnel record on a specific job, and the report cites each of those directly.
The company has no office in San Francisco. Technicians are mobilized to the site, and travel and equipment shipping are part of the quotation so scope and logistics are agreed before work starts.
What a San Francisco UT report records
- Member, weld or line identification with drawing, detail or isometric reference.
- Procedure number, revision, code and edition, and the acceptance class applied.
- Instrument, probes, couplant and calibration blocks, with the calibration check at the start and end of the shift.
- Technician and level, with the Level III who approved the technique.
- Thickness readings by location, with minimum, average and a sketch of the grid.
- Weld indications by position, length, amplitude or size, with accept or reject disposition.
- Areas not examined and the reason, such as access, coating or geometry limits.
Reports are written so a structural engineer, a special inspector or a plant inspector can use them without a phone call to clarify.
Planning ultrasonic work in San Francisco
Urban access sets the schedule. Work on building frames is sequenced with the steel erector, crane and street permits, and examination windows are short because the next trade is waiting. On the waterfront, tides and vessel movements shape access, and shipyard work follows docking dates. Parking, loading and elevator limits matter more here than anywhere else in the Bay Area, so list them in your quote request.
The climate is gentle for UT most of the year. Cool, damp mornings are common, and steel that sat out through a cold night can be colder than the air and collect dew, so surfaces are dried and checked before coupling. Wind on piers and high steel can make instruments hard to handle, and windbreaks or tethering are used. Hills add transport time between sites, and crews allow for it rather than promise tight transfers.
For refinery and chemical plant work across the bay, site orientation and permits at each plant add lead time. Provide your safety and access requirements with the request so that mobilization can be planned around them.
Choosing between UT, MT and PT in San Francisco
Use UT for thickness and for flaws inside welds. Use magnetic particle testing in San Francisco for surface cracks in carbon and low-alloy steel, and liquid penetrant testing in San Francisco for stainless, aluminum and other non-magnetic material. Structural welds often receive UT for the volume and MT for the surface. Our national ultrasonic testing page and the complete UT guide cover the method in general, and the California inspection services page lists related services.
Developing UT skills in your own team
For an owner or fabricator who wants in-house capability, Atlantis offers UT Level 1 and UT Level 2 training under SNT-TC-1A, with practice on the UT simulator. The San Francisco training page explains how courses and employer practical hours fit together, and the eligibility checker shows what experience a candidate needs.
Frequently asked questions
Does Atlantis have an office in San Francisco?
No. The company has no office in San Francisco, and technicians are mobilized to your building site, pier, yard or plant for the agreed scope, and travel is included in the quotation.
What does San Francisco require for structural weld inspection?
The Department of Building Inspection requires special inspection, with continuous inspection and nondestructive testing for most structural welding other than certain fillet welds. The owner or engineer of record employs the special inspector.
Can Atlantis serve as the special inspector on a building project?
No. The special inspector is employed by the owner or the engineer of record under the city rules. Atlantis can perform ultrasonic examination of welds when the engineer orders it and report the results.
Can UT be used on bridge steel?
Yes. Bridge welds are examined under the contract and AWS D1.5, and ultrasonic examination is a standard tool for groove welds. The contractor quality control plan and the owner assurance program define who performs which examination.
Can you measure ship hull thickness at the Pier 70 shipyard?
We can take thickness readings for an owner. Atlantis is still in the process of obtaining UR Z17 approval from DNV, Lloyd's Register and ABS for thickness measurement, so such readings support owner decisions and are not submitted for class credit.
How does fog or salt air affect ultrasonic testing?
Moisture and salt film change coupling and corrode blocks and cables. Surfaces are wiped dry and re-coupled, calibration is checked more often, and equipment is cleaned after use near the bay.
What is the difference between UT thickness gauging and UT weld inspection?
Thickness gauging reads remaining wall with a straight-beam probe. Weld inspection uses an angled shear-wave probe and a reference level to find internal flaws, and the code sets acceptance for each.
Does Atlantis replace the API inspector on process equipment?
No. On vessels, piping and tanks covered by API inspection codes, the authorized inspector working for the owner carries the responsibility. Atlantis does the ultrasonic work and hands that inspector thickness data and indications to evaluate.
How do I ask for a UT quotation in San Francisco?
Open the quote link near the top of this page or write through the contact form. Include the member list, material, thickness range, governing document and access limits, and we reply within one business day.
Inspection and training around San Francisco
- Magnetic particle inspection (MT) in San Francisco
- Liquid penetrant testing (PT) in San Francisco
- Ultrasonic inspection services
- NDT inspection services in California
UT by industry for San Francisco: Food, Beverage & Pharmaceutical.
UT by job: Ultrasonic pipe thickness testing · Ultrasonic weld inspection · Ultrasonic boiler tube thickness testing · Ultrasonic testing of castings and forgings.
Training your own technicians: UT Level 1 training · UT Level 2 training · NDT training for San Francisco technicians.
Request an UT inspection quote for San Francisco
Send the component and material, the quantity, the code or specification and the site address. We reply within one business day with the scope, the mobilization plan and a quote. Request a quote for ultrasonic testing in San Francisco.
Need ultrasonic testing (UT) done, or learned?
Atlantis provides ultrasonic testing (UT) as an inspection service, trains technicians in it, and lets teams practise it on the Practical NDT simulator.