Ultrasonic Testing (UT) Inspection in Portland, Oregon

Atlantis NDT mobilizes Level II technicians to Portland, Oregon, for ultrasonic thickness testing and ultrasonic weld inspection on ship hulls and tanks, pressure vessels, process and utility piping, storage tanks and structural steel. Readings are taken to a written procedure, interpreted against the code or the owner's minimum thickness, and reviewed by an ASNT NDT Level III before the report is issued. Send us the asset list and access details for a Portland UT quote.

Where ultrasonic testing is used in Portland

Portland is a river port, and most of its steel sits near water. The Willamette River carries deep-draft ships to a harbor with terminals for containers, autos, liquid bulks, grain and mineral bulks, and the Swan Island industrial area, about four and a half miles downriver from downtown, holds a large ship repair yard with floating drydocks, wide fabrication bays and heavy cranes. Each of those places generates ultrasonic work. A hull that has been in salt and fresh water for years needs plate thickness mapped before steel is renewed. A fuel or liquid-bulk tank needs its shell and floor plates measured before the owner decides on repair. A crane runway girder, a steel bridge member or a fabricated structural frame needs its welds examined before it is loaded.

Inland from the river, Portland's industrial base also includes metal fabrication, equipment manufacturing, food and beverage processing with steam and ammonia systems, and the semiconductor and electronics plants in the western suburbs, which run stainless process piping and utility systems. Boilers and unfired pressure vessels in all of these plants fall under Oregon's boiler and pressure vessel rules, which makes thickness data a recurring need rather than a one-time survey.

What ultrasonic testing measures, and what it cannot see

A contact ultrasonic probe sends a short sound pulse into the steel and times the echo from the far surface or from a flaw. For thickness testing, that time becomes remaining wall once the instrument is calibrated to the sound velocity of the material. For weld examination, an angled probe sends shear waves through the weld volume so that lack of fusion, cracks, slag and incomplete penetration reflect sound back to the probe. The method sees inside the metal, which is why it is the usual choice when a surface method cannot answer the question.

It has limits that matter on Portland jobs. Sound will not cross an air gap, so a rough, scaled or heavily coated surface has to be prepared or the reading is lost. Pitted wall can return a reading from the shoulder of a pit rather than its bottom, so a thickness gauge reports the thinnest spot under the probe, not the deepest pit nearby. Coarse-grained castings and some stainless welds scatter sound and reduce sensitivity. A planar flaw lying parallel to the sound beam can be missed, which is why weld procedures call for scanning from both sides and at more than one angle where geometry allows.

Codes and acceptance criteria for Portland work

The governing document depends on what the steel is. Pressure equipment built to ASME Section VIII Division 1 uses Appendix 12 for ultrasonic examination of welds, with the technique written to ASME Section V Article 4. Process piping under ASME B31.3 follows paragraph 344.6 for ultrasonic examination, with acceptance in Table 341.3.2. Structural steel in buildings and cranes is examined to AWS D1.1, which has its own ultrasonic acceptance rules for groove welds, and steel highway bridges are covered by AWS D1.5, the bridge welding code that state transportation departments call up. Thickness measurement itself is described in ASME Section V Article 5 and standardized in ASTM E797 for contact pulse-echo gauging. In-service tanks and piping are assessed against API 653 and API 570, where the owner's authorized inspector holds responsibility and Atlantis supplies the thickness and flaw data.

Oregon adds its own layer. The state's Boiler and Pressure Vessel Specialty Code, in its 2024 edition, adopts the 2023 National Board Inspection Code, the 2023 ASME Boiler and Pressure Vessel Code, and ASME B31.1 and B31.3 piping codes with Oregon amendments. Under the state's inspection rule, power boilers are inspected yearly and unfired vessels subject to internal corrosion are inspected internally and externally every two years, so the readings feed an inspector who works to a fixed calendar. See the Oregon Building Codes Division boiler and pressure vessel page for the current code book.

How the examination is done

For thickness work, the technician first sets up on a step block of the same alloy, covering the thickness range of the job, and checks the instrument at the start and again at the end of the shift. On corroded steel a dual-element probe is the normal choice because its transmit and receive crystals are angled, which handles rough and pitted surfaces better than a single crystal. The technician watches the A-scan trace, not just the number, so a doubled echo on thin wall or a reading that jumps between two values gets noticed. Readings are taken at marked grid points or at the condition monitoring locations the owner already uses, and the same points are used each campaign so trends are meaningful.

For welds, the setup is an angle-beam probe, commonly 45, 60 or 70 degrees, with a reference level built from side-drilled holes in a block of the same thickness. Scanning covers the full weld and the heat-affected zone from the faces the geometry allows, with the sensitivity raised for scanning and indications evaluated at the reference level. Hot surfaces, for example an operating steam line, need high-temperature probes and couplant and a temperature correction, because sound speed in steel and in the probe wedge changes with heat.

Who performs and reviews the work

Atlantis has no office in Portland. Technicians travel to your site for the agreed scope. They are qualified under the company's written practice, which is built on ASNT SNT-TC-1A: a Level II sets up and calibrates the equipment and performs and interprets the examination, and an ASNT NDT Level III approves the procedures and reviews the reports. Procedure approval and report review come from our founder, Anoop Rayavarapu, who holds ASNT NDT Level III certification in UT, RT, MT, PT and VT. If your own program already has a written practice, the work can be done to your procedure instead, and our Level III consulting can review it before the job starts.

Atlantis is certified to ISO 9001 and ISO 14001. Those standards cover the management system, not the personnel qualification, which is handled under the written practice.

What a Portland UT report contains

A reader who works for an owner, a classification surveyor or an Oregon boiler inspector should be able to find the answer on the first page and the evidence behind it on the rest.

Planning a UT job in Portland

Weather drives much of the planning. Portland's wet season runs through the cooler months, and rain on outdoor steel, a wet drydock floor or a damp hull washes away couplant and leaves surfaces that need drying and cleaning before readings are repeatable. Cold mornings slow gel couplant and can chill a probe, so a technician who calibrates in a warm truck and then works on cold plate will see small errors unless the block is brought to the working temperature. Summer is dry and a better window for tank and bridge work outdoors.

Access is the other constraint. Ship repair yards have their own safety orientation and hot-work permits, and work in a tank or hold may need confined-space entry, ventilation and an attendant. Harbor terminals and plants on the river have badging requirements. Bridge members may need lift access or lane closures arranged by the owner. Tell us the access method, the surface condition and any insulation or coating that must be removed in advance, and the crew can bring the right probes, blocks and couplant on the first trip, which keeps travel to a Portland site to a single mobilization where possible.

UT, MT or PT for your Portland job

Choose ultrasonic testing when the question is how thick the wall is, or whether a weld is sound all the way through. Choose magnetic particle testing in Portland when you need surface and near-surface cracks found quickly on carbon or low-alloy steel welds, such as crane runway welds or lifting lugs. Choose liquid penetrant testing in Portland for surface-breaking flaws on stainless steel, aluminum and copper-nickel, where magnetic methods do not work. Many jobs use two: thickness first to decide where to grind, then a surface method to prove a crack is gone. The national page on ultrasonic testing sets out the full service, and the ultrasonic testing guide explains the physics in plain language.

Radiographic testing is a different case. Atlantis does not perform radiography in the United States, but ultrasonic examination can serve as the volumetric method when the code and the owner allow it.

Training your own UT technicians

If you would rather build in-house capability, the UT Level 1 training and UT Level 2 training pages describe the courses, and our NDT training page for Portland explains how theory, simulator work and the hands-on practical at your own facility fit together under your written practice. The ultrasonic testing simulator lets a trainee practice scanning and interpretation before touching a real weld.

Frequently asked questions

What does ultrasonic thickness testing cost in Portland and how is it scoped?

Cost depends on the number of locations, the surface condition, access and how far the crew travels, so each job is quoted from your asset list. Send equipment details, drawings if you have them, and the access method, and we scope the readings.

Can you do ultrasonic thickness testing on a ship hull at a Portland shipyard?

Yes, technicians can gauge hull plate and tank boundaries in a drydock or alongside. If a classification society will credit the readings to a survey, confirm that society's requirements for the gauging firm before the job, since owner-use readings and class-credited readings are not the same thing.

How do you inspect welds with ultrasonic testing?

A technician uses an angle-beam probe calibrated on a block with side-drilled holes, scans the full weld and heat-affected zone, and evaluates indications against the reference level and the acceptance criteria of the governing code, such as ASME Section VIII or AWS D1.1.

Which code applies to ultrasonic examination of steel bridge welds in Oregon?

Highway steel bridges are normally governed by AWS D1.5, the Bridge Welding Code, as called up in the owner's contract. The agency's specifications can add requirements, so we work from the contract documents and the owner's procedure.

Can ultrasonic testing find corrosion under insulation or coatings?

Thickness can be measured through intact coatings in some cases, but insulation has to be opened at the reading location. Readings taken through coating need a verified technique, so the procedure states whether the coating is removed or measured through.

Do you need to take equipment out of service for UT in Portland?

Often not for external thickness testing, since readings are taken from the outside of a vessel, pipe or tank shell while it operates, within the temperature limits of the probe. Internal access is only needed for items where the outside cannot be reached.

What does Oregon require for pressure vessel inspection?

Oregon's Boiler and Pressure Vessel Specialty Code and the state inspection rule set the inspection intervals by equipment type, and the inspector who signs is separate from the NDE technician. Our thickness data supports that inspector's decisions.

Does Atlantis have an office or crew in Portland?

No. Atlantis has no office in Portland. Technicians are mobilized to your site from outside the area for the agreed scope, and travel is planned with you as part of the quote. We reply to enquiries within one business day.

Can ultrasonic testing replace radiography on my Portland weld?

Sometimes. Some codes allow ultrasonic examination as an alternative for volumetric examination, but the substitution must be agreed with the owner, the engineer and the authorized inspector before the work, and not every weld or code permits it.

Inspection and training around Portland

UT by industry for Portland: Marine & Shipbuilding · Pulp & Paper.

UT by job: Ultrasonic pipe thickness testing · Ultrasonic weld inspection · Ultrasonic boiler tube thickness testing · Ultrasonic testing of castings and forgings.

Training your own technicians: UT Level 1 training · UT Level 2 training · NDT training for Portland technicians.

Request an UT inspection quote for Portland

Send the component and material, the quantity, the code or specification and the site address. We reply within one business day with the scope, the mobilization plan and a quote. Request a quote for ultrasonic testing in Portland.

Need ultrasonic testing (UT) done, or learned?

Atlantis provides ultrasonic testing (UT) as an inspection service, trains technicians in it, and lets teams practise it on the Practical NDT simulator.