Magnetic Particle Inspection (MT) in Norfolk, Virginia

Atlantis NDT performs magnetic particle inspection (MT, also called mag particle testing or MPI) for owners and contractors in Norfolk and Hampton Roads. Typical targets are welds on carbon and low-alloy steel, crane and rigging components, lifting lugs, pins and shafts, and repair welds at yards and terminals. Technicians travel to your site once the scope is set. Send the component list and procedure basis through the MT quote form and we reply within one business day.

Where magnetic particle inspection is used in Norfolk

Norfolk's economy is built around ships, piers and cargo handling, and that means a great deal of ferromagnetic steel carrying cyclic loads. Container terminals and the Virginia Port Authority's Norfolk International Terminals rely on cranes whose boom hinges, trolley frames and spreader connections see fatigue every working day. Ship repair yards along the Elizabeth River weld, grind and re-weld hull structure, foundations and attachments, and each repair weld may call for a surface examination before the vessel returns to service.

Away from the water, MT is part of routine work on pressure vessel nozzle welds, structural steel connections, heavy trailer and rail equipment, and the pins, hooks and shackles that make up lifting gear. Coal handling equipment at the Lambert's Point terminal and the conveyors, hoppers and structures that serve it are another field of steel where fatigue cracks start at weld toes and bolted joints.

What MT finds and what it misses

MT works by magnetizing the part. A crack or similar discontinuity that interrupts the magnetic field creates a leakage field at the surface, and fine iron particles gather there to form a visible indication. The method finds surface-breaking cracks, laps, seams and cold shuts, and can reveal discontinuities lying just under the surface. It is fast, shows the length and shape of an indication directly and works through thin non-magnetic coatings.

The limitation that decides every job is the material. MT only works on ferromagnetic steels, meaning carbon steel, low-alloy steel and most martensitic grades. Austenitic stainless steel, aluminum, bronze and nickel alloys cannot be magnetized well enough, so they need liquid penetrant testing in Norfolk instead; penetrant is the normal route for those metals. MT also misses flaws deeper than a short distance below the surface, and a crack lying parallel to the magnetic field gives almost no indication, which is why each area is examined with the field applied in two directions.

Codes and acceptance criteria

The technique comes from ASME Section V Article 7, and the details are explained in our Article 7 guide. ASTM E709 is the general guide and ASTM E1444 is the practice used on many contracts. Acceptance comes from the construction code: Appendix 6 of ASME Section VIII Division 1 for pressure vessels, paragraph 344.3 and Table 341.3.2 of ASME B31.3 for process piping, and the AWS D1.1 or D1.5 criteria for structural and bridge welding.

In Virginia, boilers and pressure vessels fall under the state Department of Labor and Industry program, with rules in Title 16, Agency 25, Chapter 50 of the Virginia Administrative Code. Equipment must be ASME-built and registered with the National Board, and inspections are performed by insurance company, contract fee or owner-user inspectors who hold Virginia commissions. Where API 510, 570 or 653 applies, the owner's authorized inspector remains responsible for the inspection, and Atlantis reports the examination data used in that file.

How the examination is performed

Preparation matters as much as magnetizing. Weld spatter, loose scale, heavy rust and grease are removed so particles can reach the surface and indications can form. Thick coatings may need local removal. For most field work the technician uses an electromagnetic yoke on the weld and the heat-affected zone, then repeats with the yoke turned about ninety degrees so cracks in any direction cross the field.

Yokes are checked before use against a lifting test: an alternating-current yoke must lift at least ten pounds at the pole spacing in use, and a direct-current or permanent-magnet yoke at least forty pounds, per Article 7. Field strength is also confirmed with a pie-shaped or strip indicator. Dry visible powder suits warm, clean surfaces; wet particles, either visible or fluorescent, give better sensitivity on smooth parts. Fluorescent work needs a darkened area and a UV-A lamp whose intensity has been measured. After examination the part is demagnetized when a residual field would interfere with welding, machining or later operations, and the procedure states when that is needed.

Prods, yokes and wet particles: choosing a technique

A yoke is the default tool on ship and terminal steel because it leaves no arc strikes. Prods pass current through the part and can magnetize large castings or thick plate, but they can burn the surface and are restricted or banned on many specifications. Wet fluorescent MT is common in workshops on pins, shafts and small fabrications, where a portable UV lamp and a shaded corner of a shop floor are enough.

Underwater MT of piers or hulls is a specialist operation requiring divers and is not part of this service. Everything described here is carried out in air, on accessible steel, to the written procedure agreed beforehand.

Crane, rigging and lifting-gear examinations

Lifting equipment is the most frequent MT subject on a working waterfront. Hooks, shackles, padeyes, sling pins, sheave shafts and crane hinge pins are forged or machined carbon and alloy steel, they carry repeated heavy load, and their failure modes start as fine fatigue cracks at fillets, keyways and thread roots. MT shows those cracks long before they threaten the load path. A periodic examination program, with each part cleaned, magnetized and recorded against its identification, gives the owner a history of the part rather than a single pass-fail snapshot.

Disassembly is often the difficult part. A pin examined in place may have its critical zone hidden under a bushing, so the examination scope should state whether the pin is removed first. Atlantis can examine accessible faces on site, and the owner or crane maintenance contractor handles rigging, lockout and any component removal. The inspection criteria for the lifting equipment itself come from the equipment manufacturer, the owner's program or the governing crane standard, and the technician applies the limit stated in the contract.

Repair welds and grind-outs

Another common job is checking a repair. When a crack or defect is ground out of steel, MT confirms that the excavation has reached sound metal before welding begins, and again after the repair weld is complete and dressed. Doing the first check saves repeated weld cycles; doing the second documents the final condition. Because MT is quick, a technician can work alongside a welder and examine each stage without holding up the schedule.

On pressure-retaining steel, preheat and post-weld heat treatment affect what happens next. Particles do not tolerate high surface temperature, so the part must cool within the procedure's allowable range before wet or dry examination. Where a repair has been made to a boiler or pressure vessel, the National Board Inspection Code and the state jurisdiction control who may accept the repair, and our report is data for that decision.

Who performs the work

Atlantis technicians who carry out MT are qualified under the company's written practice, based on ASNT SNT-TC-1A. A Level II technician selects the technique, performs the examination, interprets indications and records results. An ASNT Level III approves the written procedure and the report format. Under SNT-TC-1A the employer issues certification, and in this case that employer is Atlantis for its own staff.

Where your company has its own written practice or a customer-specified procedure, we can work to it after a review. The written practice development service helps owners who need a procedure built to a stated code.

What the MT report contains

Reports identify the component, location and drawing reference, the procedure and revision, the magnetizing equipment and its calibration status, the particle type and carrier, the field direction and number of passes, the technician and level, and the surface preparation and temperature. Each indication is described by location, length and orientation with a photograph or sketch, followed by an accept or reject call against the named criteria. Parts that required demagnetizing are noted.

For fatigue-critical items such as crane pins or lifting lugs, the report can record each examined face so a later inspection can compare the same locations.

Planning an MT job in Norfolk

Humidity is the main local factor. Summer air in Hampton Roads is muggy, with a typical July high near 87 degrees Fahrenheit, so wet surfaces, condensation on cooled steel and sweat-soaked gloves all change particle behavior and visibility. Winter brings windy conditions and January lows averaging in the mid-30s, so very cold steel needs the procedure's lower temperature limit confirmed before the wet method is used. Outdoor work at a pier or terminal is easier in the early part of the working day when sun glare is lower, particularly for visible particles.

Access and safety orientation at terminals, drydocks and plants should be arranged in advance, and electrical safety rules often govern the use of a mains-powered yoke near water. Give us the working surface, the power available and whether wet work is allowed, and travel is planned around those details.

Scoping questions that speed up a quote: Which components, and how many of each? Is the steel carbon or alloy, and has it been coated or galvanized? What temperature is the surface likely to be at the time of examination? Is there a customer procedure or code edition to follow? Who will provide access equipment, power and escorts? Answers to these let us confirm that MT is the right method, choose dry or wet particles and plan the number of technician days without guessing.

Because Hampton Roads work often involves tide, vessel schedules and terminal operations, flexibility on timing helps. If the component cannot be reached until a vessel sails or a crane is parked, say so in the request and the plan can be built around that window.

MT, PT or UT for your Norfolk job

Use MT for crack-finding on ferromagnetic welds and parts. Use PT when the metal is stainless, aluminum or any non-magnetic alloy, or when the area is too awkward to magnetize. Use UT in Norfolk when thickness or subsurface weld quality is the question rather than a surface crack. The MT versus PT comparison sets out the trade-offs, and the national MT service page summarizes general capability.

Training your own MT technicians

If your team wants in-house MT capability, MT Level 1 training and MT Level 2 training cover the theory and technique. Your company certifies under its written practice; Atlantis delivers the instruction. The Norfolk training page describes how that blends with hands-on practice at your facility.

Frequently asked questions

What is magnetic particle inspection used for in Norfolk?

It is used to find surface and slightly subsurface cracks in carbon and low-alloy steel: ship repair welds, crane components, lifting lugs, pins, structural connections and pressure vessel nozzle welds at yards, terminals and plants.

Can MT be used on stainless steel or aluminum?

Not effectively. Austenitic stainless steel, aluminum and most non-ferrous alloys cannot be magnetized well enough for particles to gather, so those alloys are routed to dye penetrant inspection.

Do you inspect underwater steel in Norfolk?

No. Atlantis performs MT in air on accessible steel. Underwater examination needs diver support and is a separate specialist scope that is not offered through this service.

How much surface preparation is required before MT?

Loose scale, spatter, oil and heavy rust must come off so particles reach the metal. Thin tight coatings are often acceptable if the procedure allows it, while thick or flaking coatings need local removal.

Do you demagnetize parts after MT?

Yes, when a residual field would interfere with welding, machining, bearings or later service. The procedure states whether it is required, and the report records that demagnetizing was carried out.

Which code sets the acceptance criteria for MT in Norfolk?

The construction code or contract governs, such as ASME Section VIII Division 1 Appendix 6, ASME B31.3 or AWS D1.1. ASME Section V Article 7 supplies the technique, not the pass-fail limit.

Can you work to a Navy or customer-specific MT procedure?

We can review a customer procedure and work to it when our written practice and personnel meet its stated requirements. Naval contracts have their own rules, which this service does not claim to satisfy.

How do I request an MT quote for a Norfolk job?

Send component details, material, code basis, access and timing through the quote form. We reply within one business day with questions or a scope-based quotation, and technicians travel to your site.

Does Atlantis staff an office in Norfolk?

No. Atlantis has no office in the city. Technicians are mobilized to your site, and access, safety orientation and power supply are confirmed with you before they travel.

Inspection and training around Norfolk

MT by industry for Norfolk: Marine & Shipbuilding · Rail.

MT by job: Magnetic particle weld inspection · Magnetic particle inspection of lifting equipment · Magnetic particle inspection of castings and forgings · Magnetic particle inspection of structural steel and bridges.

Training your own technicians: MT Level 1 training · MT Level 2 training · NDT training for Norfolk technicians.

Request an MT inspection quote for Norfolk

Send the component and material, the quantity, the code or specification and the site address. We reply within one business day with the scope, the mobilization plan and a quote. Request a quote for magnetic particle inspection in Norfolk.

Need magnetic particle testing (MT) done, or learned?

Atlantis provides magnetic particle testing (MT) as an inspection service, trains technicians in it, and lets teams practise it on the Practical NDT simulator.