Magnetic Particle Inspection (MT) in New Orleans, Louisiana

Atlantis NDT mobilizes Level II technicians to New Orleans area sites for magnetic particle inspection of welds, forgings, castings and in-service steel. If the question is whether a crack has opened at a repair weld, a crane attachment, a vessel nozzle or a structural joint, MT answers it in minutes and leaves a visible, photographable record. Send the component, the code and the access details through the quote link and we reply within one business day: request an MT quote for New Orleans.

Where magnetic particle inspection is used around New Orleans

The Mississippi River defines the work. Port NOLA handles containers, breakbulk and heavy lift across a river frontage served by six Class I railroads, and the cranes, spreaders, hooks, lifting beams and rail-mounted equipment that move that cargo carry highly loaded welds. Bulk handling for grain and chemicals adds conveyors, elevator structures and loading equipment, all of them cyclic-load structures where fatigue cracks start at weld toes and attachments. Barge fleeting, repair and fabrication around the river and canals involve welded hull and deck steel, bitts, cleats and tow knees that take shock loads.

Petrochemical plants line the river above the city, and their pressure equipment, structural supports and pipe racks keep repair crews busy with weld repairs that need a surface crack check before release. The Michoud Assembly Facility, built by NASA in 1961, is a reminder that large welded fabrications are also part of the local picture. Wherever welded carbon or low-alloy steel is loaded, vibrated or thermally cycled, MT is the practical surface test.

What MT finds, and the cases where it cannot be used

The method rests on stray flux at a crack. Magnetize a ferromagnetic part, and any crack across the field forces flux out of the surface at the crack. Fine iron particles applied to the surface gather there and form a line that is easy to see. So the part must be ferromagnetic: carbon steel, low-alloy steel and martensitic stainless are suitable, while austenitic stainless, aluminum and bronze, common in chemical and marine service, are not and need liquid penetrant testing instead.

Depth sensitivity is the limit. MT is strongest at the surface, weakens quickly with depth, and does not size a crack. Heavy coatings, wet scale, thick spatter and oil keep particles from moving into place, and Gulf Coast humidity and rain make surface condition a daily concern. MT does not measure thickness; a thinned wall needs ultrasonic testing. Because a crack is detected best when it lies across the field, two field directions are always used.

Equipment and techniques used in the field

The workhorse is the electromagnetic yoke. Under ASME Section V Article 7 an AC yoke must lift at least 10 pounds at the largest pole spacing used, and a DC or permanent-magnet yoke at least 40 pounds, so the technician checks lifting power with a test weight before starting. Prods are an alternative where yoke legs cannot reach, used carefully so they do not burn the surface. Coils and a central conductor are used on shop-sized parts when there is a need for circular or longitudinal fields.

Wet particles in a spray carrier are favored in humid conditions because they stay on the surface and give clear indications on rough weld profiles. Visible particles in a contrasting paint suit daylight work on docks and decks. Fluorescent particles are the most sensitive, but are examined under UV-A light in a darkened area, so a portable tent is used on open sites. A field indicator or a shim confirms that the field is strong enough in the direction needed. On wet days the surface must be dried before particles are applied, or the carrier will not behave.

Codes and acceptance criteria

ASME Section V Article 7 defines the method and ASTM E1444 is the standard practice, with ASTM E709 as the guide. For vessels, ASME Section VIII Division 1 Mandatory Appendix 6 sets methods and acceptance. For piping, ASME B31.3 paragraph 344.3 and Table 341.3.2 apply. For structural steel and cranes, AWS D1.1 and the manufacturer's or owner's lifting-equipment criteria apply, and for pipelines API 1104 and PHMSA rules in 49 CFR Parts 192 and 195 set the framework.

Under API 510, API 570 and API 653 the owner's authorized inspector holds responsibility for the inspection program, and the MT report supports that inspector's decisions. OSHA 29 CFR 1910.119(j) requires covered process facilities to inspect and test equipment to recognized and generally accepted good engineering practice, which is how many owners justify routine MT on welded repairs.

Bridges and river crossings are a further use of MT in a region full of water. Steel bridge members and connections that fall under state transportation-department specifications are welded and inspected to AWS D1.5, and fatigue-prone details such as cover-plate ends, stiffener welds and attachment toes are the classic places for magnetic particle checks. Elevated steel exposed to salt air and wet weather develops coating breakdown that can hide cracking, so a localized coating removal followed by MT is a common approach when a crack is suspected.

Repair welding adds its own timing questions. On thicker or higher-strength steel, delayed hydrogen cracking can appear hours after a weld cools, so the owner's procedure may require a hold period before final MT. Surface checks are also often done on the gouged groove before welding, between passes on critical joints, and after any post-weld heat treatment. Tell us which stage you need and we will write it into the scope.

Louisiana's state role for pressure equipment

Louisiana law places boilers under the authority of the assistant secretary of the Office of State Fire Marshal, Code Enforcement and Building Safety, who may investigate, adopt rules and issue enforcement orders. The rules follow the ASME boiler construction code in general, and ASME-stamped boilers and pressure vessels must be inspected under the ASME Code and National Board standards.

When a stamped vessel has had a repair, the repair documentation follows the National Board Inspection Code and the owner's quality program, and the MT record becomes part of that package. Atlantis is not the commissioned inspector for the state or an insurer. If you tell us which inspector will accept the work and what they need to see, the MT report can be set up to match.

After the examination: demagnetizing, cleaning and disposition

A magnetized part can attract chips and fines, push a welding arc off course, and disturb nearby instruments. If the procedure or the next operation requires it, the technician demagnetizes with a yoke or coil and confirms with a field meter. Particles and carrier are cleaned off, and marks used to locate indications are recorded.

Indications are first sorted into relevant and non-relevant. A relevant linear indication is measured and compared with the acceptance criteria, marked on the part and photographed. Rejectable indications go to the owner, welding engineer or authorized inspector for disposition, and repaired welds are re-examined with the same procedure.

Who does the work and checks it

Atlantis has no office in New Orleans. Our technicians travel to your site and perform MT under the company's written practice, built on ASNT SNT-TC-1A. A Level II sets up equipment, performs the examination and interprets indications, and an ASNT Level III approves the procedure and reviews the report. For Louisiana MT scopes that Level III is Anoop Rayavarapu, ASNT NDT Level III in UT, RT, MT, PT and VT. The company's ISO 9001 and ISO 14001 certificates cover its management systems.

SNT-TC-1A is an employer-based recommended practice, so the details belong to the employer. If your contract requires a particular qualification route or a procedure approved by your own Level III, tell us when you ask for the quote.

What the MT report contains

Planning an MT job in New Orleans

Humidity, heat and rain shape every outdoor job here. A damp surface blocks particle movement, so drying time must be built in, and a sudden storm can end the day at an exposed dock or pipe rack. Summer sun can heat steel enough to dry the carrier before indications form, so work shifts to cooler hours or shade. Hurricane season from June through November means mobilization dates need some flexibility.

Docks, plants and terminals typically require site badging or TWIC, orientation and permits for hot work and confined space, and turnaround seasons strain local lodging. MT needs clearance around the weld for the yoke, good lighting and safe access, so scaffolds, lifts and lighting should be arranged beforehand. Tell us the component, surface condition, expected permits and working window, and we plan travel and equipment from that.

Lighting is easy to underestimate on river sites. Visible-particle work needs adequate white light at the surface, and a shaded pipe rack or the underside of a dock deck can be too dark without portable lamps. Glare off wet steel hides faint indications too. We ask about lighting and power at the work location, and bring our own lamps and a light meter, so indications are judged under the conditions the procedure requires and each result can be reproduced by the next inspector.

It also helps to decide who will remove coatings, provide access and give hot-work permits before the technician is sent, since waiting on those items is where most schedule slippage originates on terminal and plant jobs.

MT, PT or UT for your New Orleans job

Choose magnetic particle inspection for surface and near-surface cracks in steel. Choose penetrant testing for non-magnetic metals, or where a yoke cannot be positioned. Choose ultrasonic testing for wall loss and internal weld flaws. A repair on a river-corridor vessel could well use all three. For more depth, see the national magnetic particle testing page, the MT guide, the MT versus PT comparison, and the Louisiana inspection hub.

Training your own MT technicians

If crack checks are a constant need, consider building the skill in-house. Atlantis runs MT Level 1 training, MT Level 2 training and general magnetic particle testing training. Qualification is set by the employer's written practice, so supervised experience hours still apply. See the New Orleans NDT training page and the Article 7 explainer.

Frequently asked questions

What can magnetic particle inspection be used on in New Orleans plants?

Any ferromagnetic steel: carbon and low-alloy steel welds, castings, forgings, crane parts and structural members. It does not work on austenitic stainless, aluminum or bronze, which need penetrant testing instead.

Does MT work in humid, rainy conditions?

It can, with care. The surface must be dry and clean for particles to move, so we build drying time into the plan and use wet particles or a tent where weather would otherwise ruin the result.

Can MT find cracks below the surface?

Only shallow ones. Sensitivity falls quickly with depth, and MT cannot size a crack, so a relevant indication goes to the engineer or authorized inspector for disposition.

Is MT used on dock cranes and rigging?

Yes, it is a standard crack check for crane booms, hooks, lifting beams and attachment welds on ferromagnetic steel. The scope should state the owner's lifting-equipment program and the criteria that apply.

Which acceptance criteria apply to my weld?

Those in the governing code, such as ASME Section VIII Appendix 6 for vessels, ASME B31.3 Table 341.3.2 for process piping or AWS D1.1 for structural steel. Name the document in your request.

Does Atlantis have a New Orleans office?

No. Technicians travel to your site for the agreed scope, and we quote travel from the job details without promising an arrival time before access and scope are confirmed.

Do I need to demagnetize parts after MT?

Only when the procedure or the next step requires it, for example before welding or when chips would be a problem. We check residual fields with a meter and demagnetize when necessary.

Can paint stay on during MT?

Thin, well-bonded coatings can sometimes be examined if the procedure allows, though sensitivity drops. Thick or flaking coatings should be removed locally before the examination.

What qualifications do your MT technicians hold?

Qualification follows Atlantis' written practice, which is built on ASNT SNT-TC-1A, and an ASNT NDT Level III signs off procedures and report review. Tell us if your contract requires another scheme.

Can my team learn MT rather than hire a crew?

Yes. MT Level 1 and Level 2 training is available, and your company's written practice governs qualification and the experience hours required before independent work.

Inspection and training around New Orleans

MT by industry for New Orleans: Petrochemical · Offshore · Marine & Shipbuilding.

MT by job: Magnetic particle weld inspection · Magnetic particle inspection of lifting equipment · Magnetic particle inspection of castings and forgings · Magnetic particle inspection of structural steel and bridges.

Training your own technicians: MT Level 1 training · MT Level 2 training · NDT training for New Orleans technicians.

Request an MT inspection quote for New Orleans

Send the component and material, the quantity, the code or specification and the site address. We reply within one business day with the scope, the mobilization plan and a quote. Request a quote for magnetic particle inspection in New Orleans.

Need magnetic particle testing (MT) done, or learned?

Atlantis provides magnetic particle testing (MT) as an inspection service, trains technicians in it, and lets teams practise it on the Practical NDT simulator.