Magnetic Particle Inspection (MT) in Milwaukee, Wisconsin
Atlantis performs magnetic particle inspection (MT) on ferromagnetic welds, castings, forgings and structural steel at Milwaukee foundries, fabrication shops, plants and port facilities. Technicians mobilize to your site, work to a written procedure, and report each indication against the acceptance criteria your code names. Send the component list, surface condition and access details through the MT quote form and we reply within one business day.
Where magnetic particle inspection is used in Milwaukee
Few American cities have as much heavy steel work packed into one metro area. Milwaukee's foundries pour gray iron, ductile iron and steel castings, its forge shops make shafts and gear blanks, and its fabricators weld frames, booms and housings for cranes, mining machines and drivelines. All of these are ferromagnetic, they carry cyclic loads, and the failure mode that worries owners is a fatigue crack that starts at a surface discontinuity. That is exactly what MT is built to find.
Outside the shops, MT is used on lifting lugs and pad eyes before heavy picks, on crane runway and hook details at the Lake Michigan harbor, on structural welds in buildings and bridges, and on repair excavations before rewelding. Brewery and food-plant jobs rarely need MT because their vessels are stainless steel, which is not magnetic, but the carbon steel supports, platforms and structural frames around them often do.
What MT finds, and what it misses
Magnetic particle testing magnetizes a ferromagnetic part and applies fine iron particles. Where a crack or seam interrupts the field, flux leaks out of the surface and the particles gather, drawing a visible line. It detects surface-breaking and slightly subsurface discontinuities such as cracks, laps, seams, cold shuts and incomplete fusion at the toe of a weld.
It works only on ferromagnetic material. Carbon and low-alloy steels and most cast irons qualify; austenitic stainless steel, aluminum and copper alloys do not, and those go to penetrant testing instead. The field must cross the discontinuity at a useful angle, which is why two examinations at roughly right angles are required. MT does not size depth, does not find deep internal flaws, and thick paint or scale can weaken the indication. Residual magnetism after the test can also be a nuisance on machined parts.
Codes and acceptance criteria for Milwaukee MT work
The method is written to ASME Section V Article 7, which sets how the part is magnetized, the equipment checks, the lighting for visible particles and the ultraviolet intensity for fluorescent ones. ASTM E709 is the guide behind it and ASTM E1444 is the practice many specifications cite. For pressure vessels built to ASME Section VIII Division 1, Mandatory Appendix 6 gives the MT method and its acceptance standards. Process piping under ASME B31.3 uses paragraph 344.3 and Table 341.3.2.
Structural fabrication in Wisconsin usually follows AWS D1.1, and bridge members follow AWS D1.5, both of which accept MT as a surface examination. The owner of an in-service boiler or pressure vessel in Wisconsin deals with the Department of Safety and Professional Services under SPS 341, and repairs follow the National Board Inspection Code. The Article 7 explainer walks through the method requirements in plain language.
Technique: yokes, prods, wet and dry
For field work in Milwaukee the standard tool is the electromagnetic yoke. An AC yoke must lift at least 10 pounds at the pole spacing used, and a DC or permanent-magnet yoke at least 40 pounds, and the technician proves this with a test weight before the shift. Prods pass current directly into the part and are used on heavy sections, but they can arc-burn the surface, so many procedures restrict them or forbid them on finished parts.
Visible dry powder suits rough welds and hot surfaces. Wet visible and wet fluorescent suspensions are more sensitive, and fluorescent work needs a darkened area and UV-A light at the intensity the procedure states. A field indicator, such as a pie gauge or shim, confirms that the field is strong enough in the direction needed. After the examination, parts that will be machined, welded or run near sensitive instruments are demagnetized and the residual field is checked.
Typical discontinuities in Milwaukee castings, forgings and weldments
Each product form fails in its own way, and the technician looks for it. Castings show shrinkage cracks, hot tears and cold shuts, often near section changes, and heavy gray and ductile iron parts can also show surface porosity that clusters into a visible indication. Forgings show laps, seams and quench or grinding cracks, usually running along the grain direction. Weldments show toe cracks, crater cracks, lack of sidewall fusion and underbead cracking in hardenable steels.
In service, fatigue cracks start at stress concentrations: fillet toes, keyways, the root of gear teeth, lifting-lug welds and weld terminations on crane structure. Those are the places a Milwaukee owner usually asks us to look. Arc strikes and grinding burns, which look minor, are also found and are recorded because they can start cracks later.
Heavy sections, coils and magnetizing current
Large Milwaukee parts such as crane hooks, shafts and thick-walled housings sometimes cannot be magnetized well with a handheld yoke. For those, a flexible cable wrapped around the part makes a coil that sets up a longitudinal field, and a central conductor threaded through a bore sets up a circular one. The procedure states the ampere-turns or current needed, and the part's length-to-diameter ratio influences how many shots are needed. Field indicators confirm the result on the actual surface.
Surface preparation, lighting and system checks
The result of an MT examination is only as good as the surface it is performed on. Heavy scale, loose paint, weld spatter and oil must be removed in the zone to be examined, and the surface should be dry. Under visible light, the part must be lit to the level the procedure states, measured with a light meter, and for fluorescent work the UV-A intensity at the surface and the ambient white light are both measured and recorded.
For wet systems the technician checks particle concentration with a settling test and confirms system performance on a reference part or ring. For dry systems the yoke lifting test is repeated whenever the equipment is moved or the pole spacing changes. These checks are what make a clean result believable, and they appear in the report so a reviewer can see they were done.
Who performs and reviews the work
A Level II technician qualified under the Atlantis written practice to ASNT SNT-TC-1A sets up the equipment, performs the examination and interprets the indications. An ASNT Level III signs off the written procedure and checks the finished report before it leaves our hands. That review role is held by Anoop Rayavarapu, ASNT NDT Level III in UT, RT, MT, PT and VT, for Milwaukee magnetic particle work. The employer, not a training school, issues certification under SNT-TC-1A, so crews are expected to hold current records of training, experience, examination and vision checks.
Where a Milwaukee customer has its own procedure, we compare it with ASME Section V before mobilizing and raise any gaps in advance. A new or revised procedure can be prepared through Level III consulting.
What a Milwaukee MT report contains
- The part, weld or casting identification, drawing reference, material and surface condition.
- The procedure number and revision, the code and edition, and the acceptance standard used.
- The method: yoke, prods, coil or other technique, wet or dry, visible or fluorescent, and the particle product.
- Equipment checks: yoke lifting test, light meter readings, particle concentration and system performance.
- Each indication's location, orientation and length, with a sketch or marked photograph and an accept or reject decision.
- Demagnetization performed and the technician and reviewing Level III by name and level.
Relevant, non-relevant and false indications are separated in the record, because not every particle gathering is a defect. Atlantis reports what was found; disposition and repair belong to the owner under the governing code.
Planning an MT job in Milwaukee
Winter is the main constraint. Visible and fluorescent liquids behave differently on cold steel, condensation forms when cold parts are brought into a warm shop, and gloved hands make fine yoke placement harder. Procedures should state the lowest surface temperature the technique has been demonstrated at. In summer, hot sun on outdoor steel changes how carriers dry. Fluorescent work outdoors needs a tent or blackout cover so ambient light stays within the limit.
Foundry and forge schedules often drive timing: castings are examined after cleaning and before machining, forgings after heat treatment. Industrial sites require badging and orientation, and harbor facilities have their own security rules. Surface preparation is the hidden cost of any MT job, since heavy scale, paint or weld spatter has to come off at the examination zone.
Repair excavations and in-service checks
One of the most common reasons a Milwaukee owner calls for MT is a repair. When a crack is ground out of a weld or a casting, the excavation is examined by MT before welding to prove the crack is gone, and the finished repair is examined again after grinding. The same sequence applies to temporary attachments removed from vessels or structural steel. Recording both examinations in one report gives the owner and the inspector a clear chain of evidence.
MT, PT or UT for your Milwaukee job
If the part is carbon or low-alloy steel and the concern is a surface crack, MT is the quickest and most sensitive field choice. If it is stainless steel, aluminum or any non-magnetic alloy, use dye penetrant inspection in Milwaukee. If the question is wall thickness or a flaw buried inside a weld, use ultrasonic testing in Milwaukee. The national magnetic particle testing page covers the method in more depth, and the comparison guide MT versus PT helps when the material is borderline.
Training your own MT technicians
Employers with their own inspection staff can train people through MT Level 1 and MT Level 2, with online theory and a practical finished with an ASNT Level III. The NDT training in Milwaukee page lists the options, and the practice tests help candidates prepare for the written examinations.
Frequently asked questions
Which Milwaukee components can be inspected with magnetic particle testing?
Any ferromagnetic steel or iron part: welds on crane booms and frames, cast housings, forged shafts and gear blanks, lifting lugs, structural connections and repair excavations. Stainless steel and aluminum parts need penetrant testing instead.
How do wet fluorescent and dry visible particles differ in Milwaukee field work?
Wet fluorescent suspensions are more sensitive and need a darkened area and UV-A light, while dry visible powder is simpler in the field and works on rough or warm surfaces. The procedure chooses based on the code and the finish.
Does MT find cracks under paint in Milwaukee?
A thin, non-conductive coating of limited thickness may be tolerated if the technique is qualified for it, but heavy paint or scale weakens the indication. The procedure states the maximum coating thickness, and otherwise the coating is removed in the test zone.
Why is MT done twice on the same weld?
A crack is revealed only when the magnetic field crosses it at a useful angle, so ASME Section V requires two examinations at roughly right angles. That way cracks running in any direction are detected.
Is demagnetization always required after MT?
Not always. It is done when residual magnetism could interfere with later welding, machining, coating or service, or when the specification asks for it. The technician checks the residual field and records the result in the report.
Can you perform MT on stainless steel brewery tanks in Milwaukee?
Not with magnetic particles, because austenitic stainless steel is not ferromagnetic. Liquid penetrant testing is the correct surface method for stainless welds, and carbon steel supports around the tanks can still be examined by MT.
Does Atlantis have a lab or crew in Milwaukee?
No. Atlantis has no office in the city. Technicians travel to your plant, shop or yard for the agreed scope, and an ASNT Level III reviews the procedure and the report that comes out of it.
What do you need from me to quote an MT job?
Component or weld list, material, surface condition and coating, size and access, the governing code and edition, whether fluorescent or visible particles are required, dates, and any site safety or badging rules we must meet.
How quickly will an MT crew start work in Milwaukee?
Start dates depend on scope, permits and travel arrangements, which we confirm when the job is quoted. We do not promise an arrival time before the scope, site access and procedure are agreed with you.
Inspection and training around Milwaukee
- Ultrasonic testing (UT) in Milwaukee
- Liquid penetrant testing (PT) in Milwaukee
- Magnetic particle inspection services
MT by industry for Milwaukee: Fabrication & Welding.
MT by job: Magnetic particle weld inspection · Magnetic particle inspection of lifting equipment · Magnetic particle inspection of castings and forgings · Magnetic particle inspection of structural steel and bridges.
Training your own technicians: MT Level 1 training · MT Level 2 training · NDT training for Milwaukee technicians.
Request an MT inspection quote for Milwaukee
Send the component and material, the quantity, the code or specification and the site address. We reply within one business day with the scope, the mobilization plan and a quote. Request a quote for magnetic particle inspection in Milwaukee.
Need magnetic particle testing (MT) done, or learned?
Atlantis provides magnetic particle testing (MT) as an inspection service, trains technicians in it, and lets teams practise it on the Practical NDT simulator.