Magnetic Particle Inspection (MT) in Columbus, Ohio
Atlantis NDT carries out magnetic particle inspection on carbon and low-alloy steel for Columbus, Ohio owners: weld repairs on boilers and vessels, lifting gear and crane components, heavy tooling and press frames, castings and forgings, and structural steel on building and bridge projects. Technicians are mobilized to your site with yokes, particles, a light meter and field-strength indicators, and they report against the code you name. Request a mag particle testing quote for your Columbus site and we reply within one business day.
Where magnetic particle testing is used around Columbus
Central Ohio makes things from steel and moves them by road and rail. Automotive and mobility plants in Marysville, Columbus and the surrounding counties stamp, weld and assemble steel bodies and chassis parts; machinery and materials makers supply them; and fabrication shops turn out structural and plate work for the building boom around the metro. All of that equipment fatigues. Press frames crack at corners, crane hooks and lugs wear, welds on conveyors and tooling distort and crack under cycling, and every one of those cracks starts at a surface where a magnetic method sees it well.
Examples of MT work in this market:
- Press frames, die shoes and tooling bolsters in stamping plants, checked at corners and bolt-hole edges.
- Hooks, lifting lugs, shackles, spreader beams and below-the-hook devices on overhead cranes and rigging.
- Weld repair excavations and finished repairs on boilers, receivers and process vessels.
- Structural connections, base-plate welds and crane-runway steel on industrial buildings and distribution centers.
- Steel bridge members and diaphragm connections where state or county bridge work calls for weld examination.
- Gears, shafts, spindles and rebuilt machine components returning to service.
What magnetic particle inspection finds, and what it misses
When a steel part is magnetized, a crack or seam that breaks the surface forces magnetic flux out into the air, and fine iron particles gather over the leak to draw the flaw as a visible line. The method applies only to ferromagnetic material, which covers carbon steel, low-alloy steel and martensitic grades but excludes austenitic stainless steel, aluminum, copper and most nickel alloys. It finds surface and slightly subsurface discontinuities; deeper flaws and wall loss are invisible to it.
Two points control quality. A crack lying parallel to the magnetic field produces almost no indication, so the surface is examined twice with the field turned roughly ninety degrees. And particle build-up needs a clean, dry, bare surface, so heavy scale, oil and thick paint are removed first. Thin sound coatings are sometimes acceptable if the procedure has been demonstrated through them, but a coating of unknown thickness is not assumed to be harmless.
Codes and acceptance criteria that govern MT work
The method itself is written to ASME Section V Article 7, as explained in our Article 7 guide, with ASTM E1444 and the ASTM E709 guide behind it. Acceptance depends on the job: ASME Section VIII Division 1 Appendix 6 for vessels, ASME B31.3 paragraph 344.3 and Table 341.3.2 for process piping, AWS D1.1 for structural welds and AWS D1.5 for bridge welding. API 510, 570 and 653 repair work follows the construction code that applies to the equipment, and the owner's authorized inspector stays responsible for the inspection while we deliver the examination results.
In Ohio, boilers and pressure vessels fall under the Division of Industrial Compliance in the Department of Commerce, whose rules adopt the ASME Boiler and Pressure Vessel Code and the National Board Inspection Code. Welded repairs and alterations on that equipment involve commissioned inspectors and authorized repair organizations, and MT of the finished weld is usually one of the records they review.
How the examination is done
For field work the standard tool is an electromagnetic yoke. An AC yoke is used for surface work and must meet the lifting-power check in Article 7; DC and permanent-magnet yokes need a stronger pull to qualify. Where a yoke cannot reach, prods or a coil may be used under the procedure. Dry powder suits rough or hot surfaces, while wet visible or fluorescent particles give higher sensitivity on cleaned parts, and fluorescent work needs a darkened area and a UV-A source measured at the surface with a calibrated meter.
The technician checks field strength with a pie gauge or shim indicator, applies the particles while the field is on, examines overlapping areas, and repeats at the second orientation. Where residual magnetism could affect welding, machining or a later process, the part is demagnetized and verified with a gauss meter before it goes back into service.
Who performs and reviews the work
Atlantis keeps no Columbus office; examiners are mobilized from elsewhere to your site for the agreed scope. Each holds a qualification issued under the company's written practice, based on ASNT SNT-TC-1A. A Level II technician sets up equipment, applies the method and interprets indications, while an ASNT Level III approves the procedure and reviews reports. If your own written practice governs the work, we can follow it, and our written practice development and Level III consulting pages describe the support available when procedures need to be created or reconciled.
What the MT report contains
A report names the component or weld number, the drawing reference, material and surface condition, the procedure and revision, the equipment and its calibration status, the technique (yoke, prods or coil; dry or wet; visible or fluorescent), field verification, the technician's name and level, and the examination date. Each indication is described by location, orientation and length, then judged against the named acceptance criteria. Photographs or sketches are included for rejectable indications, and the report states whether demagnetization was performed and verified.
Preparing parts and surfaces
Surface condition decides whether an indication forms at all. Weld spatter, loose scale, grease and lumpy paint hold particles away from a flaw or hold them where no flaw exists, so the technician requires bare, dry steel at the examination area, extending a short distance on either side of each weld. In a Columbus plant that normally means a wire brush or flap disc pass beforehand. Contrast paint is applied where white background helps dry or wet visible particles show against dark steel.
For weld repairs, the excavation is examined before rewelding and the finished repair afterward, because each is a separate record in the repair documentation. Magnetizing across a gap, a hole or a sharp change of section throws false indications, so the technician learns the part geometry before choosing a technique.
Reading and judging indications
Not every particle line is a defect. Relevant indications come from discontinuities that interrupt the surface; non-relevant ones come from magnetic writing, changes of section, or the edge of a weld; false ones come from dirt, lint or excess particles. The technician decides which is which by re-cleaning, remagnetizing, and where necessary demagnetizing and trying again at a different field direction. Only relevant indications are measured and compared with the acceptance limits.
Linear indications, rounded indications and clusters are judged differently under most codes, so the report states the shape and size, not just that something was found. That detail lets the owner's engineer decide whether to grind out, repair or accept.
Typical MT scopes and the references behind them
| Component | What is examined | Typical reference |
|---|---|---|
| Overhead crane hooks and lugs | Surface cracks at load-bearing radii | ASTM E1444, ASME Section V Article 7 |
| Vessel and boiler weld repairs | Excavations and finished repair welds | ASME Section VIII Appendix 6, NBIC |
| Process piping welds | Surface and near-surface weld flaws | ASME B31.3 paragraph 344.3 |
| Structural steel welds | Toe cracks, underbead cracks | AWS D1.1 |
| Bridge steel connections | Fillet and groove welds | AWS D1.5 |
| Press frames and tooling | Fatigue cracks at corners and holes | ASTM E1444 with owner procedure |
Lifting equipment and fatigue-prone steel
Overhead cranes, hoists and rigging are among the most common reasons a Columbus owner calls for mag particle work. Hooks crack at the saddle and shank, lugs crack at the pinhole edge, and welded attachments on spreader beams crack at their toes. The examination is usually done as part of a periodic inspection program, with the owner's engineer or crane inspector setting the scope. We examine the load-bearing zones the program names, record each item by tag number, and report rejectable indications so the item can be removed from service before it is used again.
Fatigue shows up wherever load cycles repeat: press frames, conveyor supports, vibrating equipment skids and crane-runway welds. These areas are worth re-examining at intervals chosen from the first findings, not left to a calendar alone.
Planning a magnetic particle job in Columbus
Central Ohio is cold in January, with average lows near 22 degrees Fahrenheit and occasional dips far lower, and warm and muggy in July with highs above 85. Particle suspensions and some contrast paints behave differently at the extremes, so outdoor work on steel that has sat in the cold needs a procedure that covers the surface temperature, and very hot surfaces call for dry particles. Humidity is high for much of the year; condensation on cold steel can ruin a wet examination, so surfaces are checked and dried first.
Many Columbus plants run on tight production schedules, so mag particle work is usually fitted to planned downtime on press lines and crane inspections. Expect orientation, badging, lockout and hot-work rules at the site. Fluorescent examination needs a space that can be darkened, which on an open plant floor means a pop-up booth or a shift to a quiet period. Parts that can be brought to a booth are quicker and more sensitive than large assemblies examined where they stand, and we say so when a quote could go either way.
MT, PT or UT for your Columbus job
Magnetic particle inspection is the fast choice for surface cracks on carbon and low-alloy steel. If the part is stainless steel, aluminum or another non-magnetic material, liquid penetrant testing in Columbus is the surface method to use, and when the question is remaining wall or an internal weld flaw, ultrasonic testing in Columbus answers it. The national magnetic particle testing page, the complete MT guide and the MT versus PT comparison help with the decision, and the Ohio inspection services page lists the other services that can sit in the same scope.
Training your own MT technicians
Plants that want in-house mag particle capability can start with the MT Level 1 course and move on to the MT Level 2 course, with the NDT practice tests for exam preparation. Local details are on the Columbus NDT training page. Qualification is issued by the employer under its own written practice, which is how SNT-TC-1A works.
Frequently asked questions
Can magnetic particle inspection be done on site at a Columbus plant?
Yes. Technicians travel to your plant or yard with portable yokes, particles and a light meter, and can examine welds, lifting gear and machinery where they stand, subject to surface condition and access.
Which materials can MT inspect?
Only ferromagnetic materials: carbon steel, low-alloy steel and martensitic stainless grades. Austenitic stainless steel, aluminum and copper are not magnetizable, so liquid penetrant testing is used on those instead.
Do you check crane hooks and lifting lugs?
Yes. Hooks, lugs, shackles and below-the-hook devices are examined at load-bearing radii and welds, with the acceptance criteria taken from the owner's procedure or the standard that governs the equipment.
What is the difference between wet fluorescent and dry magnetic particle?
Wet fluorescent particles under UV-A light give the highest sensitivity on cleaned parts but need a darkened area. Dry powder is more forgiving on rough or hot surfaces and works well for field weld checks.
Why is a second examination at a different angle required?
A crack lying parallel to the magnetic field leaks almost no flux and can be missed. Magnetizing again at roughly ninety degrees ensures cracks in any orientation interrupt the field and show up.
Is demagnetization part of the job?
It is performed when residual magnetism could interfere with later welding, machining, coating or service. The technician checks the residual field with a gauss meter and records the result in the report.
Does Atlantis have a Columbus office?
No. Atlantis has no office in Columbus. Technicians are mobilized to your site, and the quote is based on your drawings, access conditions and the code the work must meet.
Can our staff learn magnetic particle testing through Atlantis?
Yes. The MT Level 1 and Level 2 courses prepare candidates, and your company then qualifies them under its written practice based on SNT-TC-1A. The final qualification comes from the employer.
Inspection and training around Columbus
- Ultrasonic testing (UT) in Columbus
- Liquid penetrant testing (PT) in Columbus
- Magnetic particle inspection services
- NDT inspection services in Ohio
MT by industry for Columbus: Power Generation · Automotive Manufacturing.
MT by job: Magnetic particle weld inspection · Magnetic particle inspection of lifting equipment · Magnetic particle inspection of castings and forgings · Magnetic particle inspection of structural steel and bridges.
Training your own technicians: MT Level 1 training · MT Level 2 training · NDT training for Columbus technicians.
Request an MT inspection quote for Columbus
Send the component and material, the quantity, the code or specification and the site address. We reply within one business day with the scope, the mobilization plan and a quote. Request a quote for magnetic particle inspection in Columbus.
Need magnetic particle testing (MT) done, or learned?
Atlantis provides magnetic particle testing (MT) as an inspection service, trains technicians in it, and lets teams practise it on the Practical NDT simulator.