Magnetic Particle Inspection (MT) in Seattle, Washington

Atlantis NDT mobilizes magnetic particle technicians to Seattle and Puget Sound sites to find surface cracks in carbon and low-alloy steel: crane pedestals, hatch corners, rudder and skeg attachments, bridge and pier steel, refinery weld repairs and lifting equipment. Send the component list and the code and we will plan the examination around your access. Request an MT quote for your Seattle site and we reply within one business day.

Where magnetic particle inspection is used in Seattle

The Seattle area builds, repairs and moves heavy steel, and most of it is exposed to fatigue and weather. Shipyards and dry docks on Harbor Island and at Bremerton handle hull repairs where the steel renewal scope depends on what a surface examination finds at fatigue-prone details: hatch coamings, crane pedestals, bulwark attachments, engine foundations and the welds around rudder horns and skegs. The ferry fleet and its terminals add vehicle ramps, transfer spans and overhead loading structures that flex with every crossing and carry cracks that begin at weld toes.

On land, western Washington's refineries bring vessels, nozzle welds and pipe supports into scope during turnarounds. The container terminals on Elliott Bay and the Duwamish Waterway rely on gantry cranes whose boom hinges, sheave pins and structural welds are examined on a maintenance cycle. Construction in the city keeps tower cranes and mobile lifting gear busy, and hooks, shackles and load-bearing welds on that equipment are examined before and after heavy jobs. Hydro and thermal plants in the region have turbine components, headers and attachment welds that take MT during outages, and fabricators across the metro build structural steel where in-process weld checks catch defects early.

What MT detects and what it cannot

Magnetic particle testing works on ferromagnetic steel only. The part is magnetized, fine particles are applied, and any crack or seam that breaks or sits just below the surface leaks magnetic flux and holds a visible line of particles. It finds fatigue cracks, crater cracks, lack of fusion at the surface and laps on carbon and low-alloy steel. It cannot be used on austenitic stainless steel, aluminum or bronze, which are common on vessels in this region, and it will not find flaws deep inside a weld.

Two practical limits matter on Puget Sound steel. Sensitivity falls when the surface is rough, scaled or covered by thick paint or marine growth, so prep has to be agreed in advance. And because a crack shows best when it crosses the field, the code requires the examination to be repeated with the field turned about ninety degrees. A single pass is not an examination. For aluminum and stainless, use penetrant testing; for wall thickness and internal flaws, use ultrasonic testing.

Codes, class rules and Washington requirements

The technique is set by ASME Section V Article 7, with ASTM E709 as a guide and ASTM E1444 as the practice. Acceptance depends on the asset. ASME Section VIII Division 1 Appendix 6 covers pressure vessels, ASME B31.3 paragraph 344.3 covers process piping, AWS D1.1 covers structural steel, and AWS D1.5 applies to bridge steel when a state agency is the owner. Hull and Navy work are surveyed to the classification society rules or the contract specification, and we confirm which one applies before agreeing to a scope.

Washington's boiler and pressure vessel law is administered by the Department of Labor and Industries and the Board of Boiler Rules, using the National Board Inspection Code for repairs. A repair or alteration on registered equipment needs a repair organization that holds the right authorization, and the examination records of the excavation and the finished weld are part of what the commissioned inspector reviews. The National Board describes the repair framework. For ferry terminal structure, the Washington State Department of Transportation explains its inspection and repair approach on the ferry terminal maintenance page. Process plants also carry a mechanical integrity duty under OSHA 29 CFR 1910.119(j). For a plain-language read of the technique rules, see the Article 7 explainer.

How the examination is carried out

For field work the technician uses an electromagnetic yoke. An alternating-current yoke has to show a lifting power of at least 10 pounds at the pole spacing in use, and a direct-current or permanent-magnet yoke at least 40 pounds, checked with a test weight before use. The yoke is set across the weld, particles are dusted or sprayed on while the field is active, and the area is read; then the yoke is rotated roughly ninety degrees for the second pass. Prods stay off finished pressure-retaining and fatigue-critical surfaces, because arc burns create new problems.

Wet fluorescent particles are chosen for higher sensitivity, for example on fatigue-critical details or hydrogen service, and require a darkened area and a UV-A lamp whose intensity is checked. Visible dry powder suits rough outdoor welds. A field indicator confirms the setup produces a usable field. Where residual magnetism could disturb later welding, machining or sensitive instruments, the part is demagnetized and measured. Coated steel can be examined through a thin non-magnetic coating only up to the thickness the procedure demonstrates, so thicker marine paint has to be removed in the examination area first.

Surface preparation on waterfront and marine steel

Preparation decides how good an examination can be. Shipyard and pier steel arrives coated, salted and fouled, and the examination area has to be brought back to clean metal or to a coating that is thin enough for the procedure to allow. Cleaning might be wire brushing, needle scaling, light grinding or abrasive blasting, and it has to be finished before the particles go on because a dirty surface holds particles that look like indications. Oil and grease must be removed or the particles clump. Weld spatter and sharp profiles are dressed so that false indications do not mask real ones.

On ships and terminals the cleaning work often belongs to someone other than the inspection crew, so it is scheduled alongside the dry-dock or terminal work plan. When blasting or painting contractors are working nearby, the examination window has to be sequenced between them, because a freshly painted surface cannot be examined and a freshly examined surface should not be recoated until the owner has accepted the result.

Common MT findings and what happens next

On Puget Sound steel the typical finds are fatigue cracks at the toes of attachment welds, cracking at the corners of cutouts and openings, and crater cracks at weld ends. Crane and lifting equipment show cracks in hook throats and at pin bores. Many rounded or very short indications turn out to be non-relevant, from a section change or rough surface, and are re-examined after light cleaning. A confirmed linear indication is marked, measured and reported. The owner, engineer or surveyor decides whether to grind, repair, renew or monitor it, and Atlantis does not make that call. After a repair, the same examination is repeated to show the crack is gone, and both reports are filed together so the history of the detail is complete.

Photographs of the marked indication and a sketch tied to a frame number or a drawing grid let the next crew find the same detail quickly, which makes year-over-year comparisons straightforward.

Who performs the work

Technicians work under the Atlantis written practice, based on ASNT SNT-TC-1A. Level II technicians perform the examination, set up the equipment and interpret indications; the procedure and the final reports go to an ASNT NDT Level III, Anoop Rayavarapu, ASNT NDT Level III in UT, RT, MT, PT and VT. Atlantis has no office in Seattle. We mobilize crews to your yard, vessel, terminal or plant with the yokes, lamps and consumables the procedure needs, and confirm travel and orientation requirements in the quote. Atlantis is certified to ISO 9001 and ISO 14001. If a class society or a prime contractor has a specific personnel requirement, tell us at the start.

What an MT report contains

Each report identifies the component and location, the procedure and revision, the yoke or equipment and its lift check, the particle type and carrier, the surface condition, the ultraviolet and ambient light readings for fluorescent work, and the technician and level. Indications are plotted on a sketch with position and length, and the disposition is stated against the criteria you named. Where the owner decides on grinding or repair, the same examination is repeated afterward and filed beside the original. The report is then reviewed by the same Level III before it is released to you.

Planning an MT job in Seattle

Damp weather is the main variable. Rain stops outdoor examination and wet steel will not hold particles, so enclosures, tarps and drying equipment are part of the plan, and winter temperatures near freezing slow the carrier fluid and change how particles behave. Salt and marine growth on waterfront steel require cleaning before readings. Dry-dock windows are short and booked in advance, ferry terminal work follows tides and vessel schedules, and overwater work from a barge depends on sea state. Refinery and port sites run badge and safety orientation steps that need lead time. Tell us the access reality and the schedule window early, and we will plan around them.

MT, PT or UT for your Seattle job

A scoping conversation settles most choices. Describe the material, the coating state and the fatigue or repair concern, and we will recommend the method that answers it, and whether pairing it with a second method on the same mobilization saves you a return visit to the yard.

For surface cracks in carbon steel, MT is fast and sensitive. For aluminum, stainless or bronze, such as vessel superstructure and propeller hardware, choose penetrant testing in Seattle. For wall loss and internal weld flaws, choose ultrasonic testing in Seattle. Many hull repairs combine all three. Our national magnetic particle testing page, the complete MT guide and the MT versus PT comparison cover the service and theory in general terms.

Training your own MT technicians

If you would rather have in-house capability, Atlantis offers MT Level 1 training and MT Level 2 training, and the magnetic particle testing training page explains how a course and practical fit your written practice. Seattle employers can read about NDT training in Seattle, and statewide coverage is on the Washington inspection services page. For a written practice, see written practice development.

Frequently asked questions

Does Atlantis have an office in Seattle?

No. Atlantis has no office in Seattle. Crews are mobilized to your yard, vessel, terminal or plant with the yokes, lamps and particles the procedure needs, and travel details are confirmed in the quote.

Can MT be used on aluminum or stainless steel?

No. Magnetic particle testing needs ferromagnetic material. Aluminum, austenitic stainless steel and bronze do not hold a useful field, so penetrant testing is the method for surface cracks in those metals.

Why is every area examined twice?

A crack shows best when it crosses the magnetic field, so ASME Section V Article 7 requires a second examination with the field turned roughly ninety degrees. A single pass can miss a crack running parallel to the field.

Can you examine through marine paint?

A thin non-magnetic coating can stay in place only if the procedure has shown it works at that thickness. Anything heavier is removed in the examination area, or the procedure is demonstrated on a painted sample.

What details on a ship do you examine?

Typical scopes are hatch coamings, crane pedestals, bulwark and foundation attachments and repair welds on carbon steel, as agreed with the owner or surveyor. Aluminum and stainless parts are covered by penetrant testing instead.

Which code sets acceptance?

The code or rule that governs the item: ASME Section VIII Division 1 Appendix 6, ASME B31.3, AWS D1.1 or D1.5, or the class or contract specification for a vessel. We confirm it before the job.

Does Washington require anything for repair records?

Repairs on registered boilers and pressure vessels follow the National Board Inspection Code under the Department of Labor and Industries. Magnetic particle records of the excavation and finished weld support the commissioned inspector review.

Who reviews your MT reports?

An ASNT NDT Level III reviews each report and approves the procedure. Level II technicians qualified under the Atlantis written practice, based on ASNT SNT-TC-1A, perform the examination and interpret indications.

Inspection and training around Seattle

MT by industry for Seattle: Marine & Shipbuilding · Aviation & Aerospace.

MT by job: Magnetic particle weld inspection · Magnetic particle inspection of lifting equipment · Magnetic particle inspection of castings and forgings · Magnetic particle inspection of structural steel and bridges.

Training your own technicians: MT Level 1 training · MT Level 2 training · NDT training for Seattle technicians.

Request an MT inspection quote for Seattle

Send the component and material, the quantity, the code or specification and the site address. We reply within one business day with the scope, the mobilization plan and a quote. Request a quote for magnetic particle inspection in Seattle.

Need magnetic particle testing (MT) done, or learned?

Atlantis provides magnetic particle testing (MT) as an inspection service, trains technicians in it, and lets teams practise it on the Practical NDT simulator.