Magnetic Particle Inspection (MT) in Baltimore, Maryland

Atlantis NDT mobilizes Level II technicians to Baltimore for magnetic particle inspection of carbon and low-alloy steel: crane structures at the harbor, weldments at fabrication shops and ship repair yards, bridge and pier steel, lifting gear and pressure equipment welds. We select the yoke, prod or wet fluorescent technique to suit the part and report every indication against the code you name. Use a quote request to send the scope and we reply within one business day.

Where magnetic particle testing is used in Baltimore

The harbor is the obvious starting point. Container and bulk terminals run large cranes whose booms, legs, trolley frames and machinery bases carry heavy cyclic loads, and the welds at stiffeners and brackets are fatigue-prone. Ship repair yards cut out and replace steel plate, weld on pads and brackets and rebuild machinery foundations, and every one of those repair welds is a candidate for surface crack examination.

Away from the water, Baltimore fabricators build structural steel, platforms, tanks and skids, and metal-working shops make forged and cast parts. Rail yards and trucking operations maintain frames, couplers and lifting equipment. Bridges are a constant presence in this city: the replacement of the Francis Scott Key Bridge after the March 2024 collapse is one of the largest steel projects on the East Coast, and the regional highway and rail network is full of welded girders where toe cracks develop. The redevelopment of the former Sparrows Point steel mill adds new terminal steel and the legacy plant equipment that comes with it.

What the method finds and where it stops

Magnetizing a steel part creates a field. If a crack breaks the surface or lies just beneath it, the field leaks out and holds fine iron particles in a visible line. Toe cracks, lack of fusion at the surface, laps, seams and fatigue cracks all show well, and the method is fast over large areas of weld.

The limits are firm. Only ferromagnetic material responds: carbon steel and most low-alloy steel. Austenitic stainless steel, aluminum and copper alloys do not, and parts made of them need penetrant testing. A flaw buried deeper than a few millimeters is invisible to the method, so it says nothing about weld volume or remaining wall. A crack parallel to the field is missed, which is why two directions are examined. Thick marine paint and heavy scale keep particles away from the steel. For the interior of a weld or the thickness of a plate, ultrasonic testing in Baltimore is the right tool.

Codes and acceptance criteria for waterfront steel

Procedures follow ASME Section V Article 7 and ASTM E1444, with ASTM E709 as the guide to the method. Acceptance criteria come from the governing code: ASME Section VIII Division 1 Appendix 6 for pressure vessels, ASME B31.3 paragraph 344.3 and Table 341.3.2 for process piping, AWS D1.1 for structural steel and AWS D1.5 for highway bridge steel. For in-service tanks, vessels and piping under API 653, API 510 and API 570, the owner's authorized inspector is the inspector of record, and Atlantis supplies the crack indications and sketches.

Maryland administers a Boiler and Pressure Vessel Safety Program through its Division of Labor and Industry. Equipment installed in the state must be built to the ASME Code and registered with the National Board, and inspections are performed by commissioned inspectors working for an authorized inspection agency. When a jurisdictional vessel is repaired, the owner's agency decides how repair welds are to be examined. Our explanation of Article 7 goes through the technical requirements, and the complete guide to magnetic particle testing gives wider background.

Technique: yokes, prods, coils and particles

Field work is mostly done with a portable electromagnetic yoke. An AC yoke must lift at least 10 pounds at the pole spacing used and a DC or permanent-magnet yoke at least 40 pounds, and the technician proves it with a test weight. Where a yoke cannot reach enough field in a thick section, prods or a coil are used under a procedure that fixes current to thickness.

Dry powder works well on rough, outdoor welds. Wet suspension applied from an aerosol or bath is more sensitive, and fluorescent versions give the highest sensitivity but need UV-A light and a darkened area, with the intensity and ambient-light limits fixed in the Article. A field indicator confirms strength and direction. Every area is examined twice with fields at roughly right angles. After examination, the part is demagnetized when residual magnetism would affect later welding, machining, instruments or bearings.

Salt air, humidity and surface condition

Waterfront steel arrives in poor condition, and surface condition drives the quality of the result. Rust, marine growth, grease, paint and weld spatter all interfere. The owner arranges blasting, wire brushing or grinding to bare metal at the weld and a margin on each side, and the technician cleans the final surface. Thin firmly bonded coatings can be examined through if the procedure has been demonstrated to work through them at that thickness.

Humidity and fog produce condensation that dilutes wet particle suspensions and breaks the particle film. Dew on morning steel is common near the harbor, so the technician may dry the surface, warm it or use dry powder. Winter cold stiffens suspensions and ice kills contrast. The procedure sets the permitted temperature range, and the report records the conditions.

Who performs the examination

Level II technicians perform and interpret the examination under Atlantis's written practice, which follows ASNT SNT-TC-1A, and an ASNT Level III approves the procedure and reviews reports. Atlantis has no office in Baltimore, so technicians are mobilized to your site for the scope you define. Atlantis is certified to ISO 9001 and ISO 14001, and the technician brings calibrated equipment and the approved procedure.

Crane structures, repair pads and lifting gear

Cranes and lifting appliances are examined where load paths change direction: boom hinge pins and lugs, sheave brackets, trolley wheel assemblies, spreader beam welds and the corners of cutouts. Ship repair work adds temporary attachments such as pad eyes, brackets and strongbacks, which are cut off after use, and the area where they were welded is ground and examined so that no crack is left in the parent plate. A removed lug is a classic place for a surface crack to hide under a fresh grind mark.

Lifting gear is examined to the owner's inspection program or the lifting standard that applies, and acceptance is often stricter than a general fabrication code. Hooks, shackles and links are examined for cracks at the shank, the saddle and the thread. Tell us which standard governs, and whether the owner allows paint removal on load-bearing parts, because the technician cannot examine a surface that is not bare.

Reading indications and avoiding false calls

Particles also collect at the edge of a weld cap, at sharp changes of section and where another magnet has touched the part. The technician sorts those non-relevant indications from real ones by demagnetizing, cleaning and reexamining in a different direction, or by lightly dressing the surface. Real indications are measured, and their length and shape decide which rule in the acceptance table applies. Cracks and lack of fusion are rejected at any size. Rejectable areas are marked on the steel and photographed if the owner wants a record, and the site contact hears about them before the technician leaves.

What the magnetic particle report contains

The report names the component and drawing, the procedure revision and code edition, the yoke or other equipment with its lifting-power check, the particles and lighting, the surface condition, and the technician and Level III reviewer. Each indication is listed with location, orientation and length and is accepted or rejected against the named criteria. Sketches or photographs are attached, and any area that could not be examined is listed with the reason. The field-strength check on the part is recorded as well, so a reader months later can see that the setup was verified instead of assumed.

A marked-up photograph taken before grinding is often the only evidence that survives once a repair is made. It lets the owner's engineer judge whether similar welds elsewhere on the same crane, pier fitting or vessel deserve a closer look, and it gives the repair crew the exact location and orientation of each crack.

Weld repairs and the examination sequence

On repairs, magnetic particle testing is used at three points: after the defect is ground out to prove the crack is gone, after the repair weld, and, for thick or restrained steel, after a delay that allows hydrogen cracking to appear. Many welding procedures require that delay before the final examination, and it can add a day to the schedule that the owner should plan for. Ask your welding engineer which holds apply, and tell us so that the technician returns at the right time.

Planning a magnetic particle job in Baltimore

Give us the season, the surface condition and whether the work is indoors or exposed. Many harbor sites are secure facilities that need a Transportation Worker Identification Credential, safety orientation and an escort, and elevated welds on cranes and piers need lift or scaffold access that the owner supplies. Arrange lighting for fluorescent work and shade for daylight work. Tell us how the job connects to I-95, I-695 and the tunnels so travel is planned, and expect dates to be confirmed when the scope is agreed.

Limited access and awkward geometry

Waterfront steel is rarely convenient. Welds sit under pier decks, inside crane legs, behind machinery guards and at the bottom of tanks and voids. A yoke is compact, which helps, but the technician still needs room to place the poles, apply particles and see the result, so tell us about confined spaces, working at height and any lighting limits. Where access is poor, the owner may need to arrange scaffold, a lift or a small cut-out, and the report will state any weld length that could not be reached.

Choosing between magnetic particle, penetrant and ultrasonic testing

Use magnetic particle testing for surface cracks in carbon steel. Use penetrant testing on stainless, aluminum and other non-magnetic metal, and ultrasonic testing when weld volume or remaining wall matters. The MT versus PT comparison helps with the choice, and the national magnetic particle testing page describes the service.

Training your own magnetic particle technicians

Atlantis teaches MT Level 1 training and MT Level 2 training. Hands-on practice and the practical exam are arranged by your company under its own written practice. See the Baltimore NDT training page or the SNT-TC-1A eligibility checker.

Frequently asked questions

What steel can be examined by magnetic particle testing in Baltimore?

Carbon steel and most low-alloy steel, which covers most crane, pier, ship repair and structural work. Stainless steel, aluminum and copper alloys are not magnetic, so those parts need liquid penetrant testing instead.

Can magnetic particle testing find cracks hidden inside a weld?

No. It finds surface cracks and flaws just under the surface. For the interior of a weld or remaining wall thickness, ultrasonic testing is used, and many Baltimore jobs combine both methods on the same weld.

Why is each area examined in two directions?

A crack parallel to the magnetic field gives little flux leakage and can be missed. ASME Section V Article 7 calls for two examinations with the field at roughly right angles so cracks in any direction show.

Can marine paint stay on the steel during the examination?

Thin, firmly bonded coating may stay if the procedure has been demonstrated through it at that thickness. Thick or flaking paint, rust and marine growth must be removed so particles can reach the surface.

How do humid or foggy conditions affect the work?

Condensation dilutes wet suspensions and breaks the particle film. The technician dries or warms the steel, or switches to dry powder, and records the conditions in the report so the examination can be judged later.

Is demagnetization always required?

No. It is required when residual magnetism could affect later welding, machining, instruments or bearing surfaces. The procedure says when, and the report states whether it was done and checked afterward.

Who decides if an indication is acceptable?

The technician judges it against the acceptance criteria in the governing code. On in-service equipment the owner's authorized inspector or engineer then makes the repair or keep-running call from the data.

Do I need a Transportation Worker Identification Credential for the job?

Many secure areas of marine terminals require one, along with safety orientation and an escort. Tell us early which areas are involved so access can be arranged before the technician travels to the site.

Can my staff learn magnetic particle testing instead of outsourcing?

Yes. MT Level 1 and Level 2 courses are available. Your company supplies the hands-on practice and the practical exam, and certifies its own people under SNT-TC-1A.

Inspection and training around Baltimore

MT by industry for Baltimore: LNG · Marine & Shipbuilding.

MT by job: Magnetic particle weld inspection · Magnetic particle inspection of lifting equipment · Magnetic particle inspection of castings and forgings · Magnetic particle inspection of structural steel and bridges.

Training your own technicians: MT Level 1 training · MT Level 2 training · NDT training for Baltimore technicians.

Request an MT inspection quote for Baltimore

Send the component and material, the quantity, the code or specification and the site address. We reply within one business day with the scope, the mobilization plan and a quote. Request a quote for magnetic particle inspection in Baltimore.

Need magnetic particle testing (MT) done, or learned?

Atlantis provides magnetic particle testing (MT) as an inspection service, trains technicians in it, and lets teams practise it on the Practical NDT simulator.