Ultrasonic Testing (UT) Inspection in Midland, Texas
Atlantis NDT performs ultrasonic thickness testing and ultrasonic weld inspection for owners in Midland and across the Permian Basin: separators and heater treaters, tank batteries, gas processing and compression piping, produced-water systems and gathering lines. Technicians are mobilized to your site with calibrated flaw detectors, dual-element probes and step blocks, work to a written procedure and report against the code you name. Request a UT inspection quote for your Midland site and we reply within one business day.
Where ultrasonic testing is used in Midland
Midland sits at the center of the Midland Basin, the eastern sub-basin of the Permian, and the steel in the surrounding counties is overwhelmingly oilfield process steel. Martin, Glasscock, Reagan, Upton and Midland counties carry cryogenic gas processing plants, high-pressure gathering pipe in 20-inch and 24-inch sizes, and compressor stations strung along those lines. Ahead of all of that sit the production facilities themselves: wellhead separators, heater treaters, free-water knockouts, atmospheric tanks and the produced-water handling that follows every barrel of oil.
Each of these has a corrosion story, and ultrasonic testing is how that story is read without shutting anything down. Typical Midland jobs include:
- Wall thickness grids on separator and treater shells, heads and nozzle necks, where produced water and carbon dioxide thin the bottom of the vessel first.
- Thickness readings at condition monitoring locations on process piping, elbows and tees downstream of compressors and in dehydration and amine service.
- Tank shell and floor-edge thickness checks on storage and produced-water tanks.
- Angle-beam examination of new and repaired groove welds on skid piping and pressure vessels built or modified in the shops that serve the basin.
- Thickness checks on pipeline risers, launcher and receiver barrels and meter-run piping at gathering stations.
The common thread is that the owner needs a defensible number for remaining wall without taking equipment out of service, and that is what the method delivers.
What UT finds and what it misses
Ultrasonic testing sends a sound pulse into the steel and times the echoes. For a thickness job the echo from the back wall gives the remaining wall directly; for a weld job, echoes from inside the weld show discontinuities that a visual check cannot reach. UT works on any dense, sound-conducting metal, so carbon steel, stainless and alloy piping all qualify, and it needs access to only one side.
Its limits matter as much as its strengths. A thickness gauge reports the wall under the probe, so a pit between two readings can be missed; this is why grids are laid out on a spacing the procedure states and why scanning with the A-scan visible is preferred over trusting a number alone. Heavy scale, loose coating and rough corrosion scatter the beam, so surface preparation comes first. Coarse-grained castings and some stainless welds attenuate sound and may need a different probe or a different method. Very thin wall, below what the probe can resolve, is measured with a different technique or flagged for another method. A UT report says what was reached and what was not, and we write it that way.
Codes and acceptance criteria behind Midland UT work
Oilfield pressure equipment is governed by a stack of documents. Thickness work on vessels and piping follows the owner's inspection program, usually built on API 510 for pressure vessels, API 570 for piping and API 653 for aboveground storage tanks. Responsibility for the inspection and the fitness decision rests with the owner's own authorized inspector; Atlantis performs the nondestructive examination and reports the data. Contact thickness measurement is generally performed to ASTM E797 and ASME Section V Article 5 and Article 23 (SE-797), and the numbers feed the owner's corrosion rate and remaining-life calculation.
Weld examination uses ASME Section V Article 4 for the technique, with acceptance coming from the construction code, for example ASME Section VIII Division 1 Appendix 12 for vessels or ASME B31.3 for process piping. Pipeline girth welds fall under API 1104 and the federal pipeline safety rules in 49 CFR Parts 192 and 195, and in Texas intrastate pipeline safety is overseen by the Railroad Commission of Texas. Pressure vessels also sit under the state boiler law administered by the Texas Department of Licensing and Regulation, and repairs and alterations follow the National Board Inspection Code. Process safety rules in OSHA 29 CFR 1910.119 require mechanical integrity programs for covered facilities, and thickness data is the backbone of those programs. Our guide to ASME Section V Article 5 thickness measurement explains the technique requirements in plain terms.
How the ultrasonic work is done
For thickness, the technician calibrates the instrument on a step block of the same material, using a dual-element probe on corroded or pitted surfaces so the two crystals can separate the transmitted pulse from the echo. With the A-scan displayed, the technician watches the signal rather than trusting a number, which prevents the double-echo errors that can make thin wall read thick. Hot surfaces on heater treaters and compressor discharge piping call for high-temperature probes and couplant, and readings are corrected for temperature when the procedure requires it. Each reading is tied to a numbered location on a sketch so the same point can be measured again at the next interval, which is how corrosion rates become meaningful.
For welds, an angle-beam probe at 45, 60 or 70 degrees sends shear waves into the joint. A reference level is built from side-drilled holes in a calibration block, the weld and heat-affected zones are scanned from both sides where geometry allows, and indications are evaluated against the code's acceptance table. Lack of fusion, cracks and slag give distinct signal patterns, and a Level II interprets them with the procedure open on the tailgate.
Turning readings into corrosion rates and remaining life
A thickness survey is only the first half of the story. The value comes when two surveys of the same locations are compared. If a separator shell read one wall thickness at the last interval and a lower one today, the difference divided by the time between surveys is the corrosion rate, and the remaining wall above the required minimum divided by that rate is the remaining life. Owners in the Permian use those two figures to set the next inspection date, decide whether a vessel can stay in service, and plan replacements before they become emergencies. Short-term and long-term rates often differ when produced-water chemistry or flow changes, which is why consistent point numbering and retained raw data matter. We deliver readings in a format your inspection group or software can import, and we flag any location that reads below the minimum or shows a sudden change so your authorized inspector sees it first.
Who performs the work
Technicians who perform and interpret UT are qualified under the company's written practice to ASNT SNT-TC-1A. A Level II sets up and calibrates equipment, performs the examination and evaluates results. An ASNT NDT Level III approves procedures and reviews reports; the founder, Anoop Rayavarapu, is an ASNT NDT Level III in UT, RT, MT, PT and VT. Procedures are written to the governing code and revision, and a procedure that does not match the code edition on your purchase order does not go to the field. If your own written practice needs work, our written practice development and Level III consulting pages describe the support.
What the UT report contains
A usable report lets the owner's inspector make decisions without a phone call. Ours identify the component and location, the procedure and revision, the instrument, probe and calibration block, the couplant and temperature, the technician and qualification level, and the date. For thickness jobs, a grid or sketch shows each reading with the nominal and minimum required wall beside it, and readings below the minimum are flagged. For weld jobs, each indication is recorded with location, length, amplitude and the accept or reject call against the named criteria. Raw readings are retained so a later survey can be compared point for point.
Planning a UT job in Midland
Several realities of the Permian shape a good plan. Summer surface temperatures on dark steel can exceed what standard probes and couplants tolerate, so high-temperature materials are specified in the scope, and winter nights can fall low enough to stiffen couplant and slow crews. Wind and blowing dust are routine, which affects surface preparation and protects the probe face from grit. Many sites are remote lease roads or gas plants with safety orientation, gate access and permit-to-work rules, so sending names and qualification records ahead of time avoids delays at the gate. Because Atlantis has no office in Midland, crews travel to your site, so we plan travel, lodging and the scope together, and turnaround and shutdown windows at plants and compressor stations are worth raising early so the job fits the outage. The Texas inspection services page covers the wider state picture.
UT, MT or PT for your Midland job
Choosing the method depends on the question. Use ultrasonic testing when the question is how much wall is left or whether a weld is sound through its thickness. Use magnetic particle inspection in Midland when the question is surface cracking on carbon or low-alloy steel, for example at weld toes on a skid or on lifting lugs. Use liquid penetrant testing in Midland for surface-breaking flaws on stainless and other non-magnetic alloys. Many owners combine them: thickness first to confirm the equipment is fit, then surface methods on the repairs. National pages on ultrasonic testing describe the method in general.
Training your own technicians in Midland
If you run your own program, qualifying employees is cheaper than traveling a contractor for routine work. Our UT Level 1 and UT Level 2 training are built around SNT-TC-1A, with practice in the UT simulator, and the Midland training page explains how courses and employer-run practicals fit together. Under SNT-TC-1A the employer certifies its own personnel; the training builds the knowledge and records.
Frequently asked questions
What does ultrasonic thickness testing cost in Midland?
Cost depends on the scope, the number of locations, surface preparation and travel to your site, so we quote each job individually. Send the equipment list and the access details through the quote link and we reply within one business day.
Can you measure wall thickness on equipment that is in service?
Yes, in most cases. Contact ultrasonic thickness readings are taken from the outside while the equipment runs, provided the surface is accessible, safe to approach and within the probe's temperature range. High-temperature surfaces need special probes and couplant.
Do you have an office or lab in Midland?
No. Atlantis has no office in Midland. Technicians are mobilized to your site for the agreed scope, qualified under the company's written practice to ASNT SNT-TC-1A, and the scope, travel and access are planned with you before the job.
How is UT different from magnetic particle or penetrant testing?
Ultrasonic testing measures remaining wall and finds flaws inside a weld, while magnetic particle and penetrant testing find only flaws that reach the surface. The right method depends on whether your concern is thinning, internal weld quality or surface cracking.
Which codes do your Midland UT reports reference?
Reports reference the code on your purchase order, typically ASME Section V for technique, ASTM E797 for thickness, and the construction code's acceptance criteria such as ASME Section VIII, ASME B31.3 or API 1104. For in-service equipment, the owner's authorized inspector makes the fitness decision.
Will you act as the API authorized inspector on our vessels?
No. The API in-service codes keep your own authorized inspector as the inspector of record. Atlantis performs the ultrasonic examination, records the thickness data and delivers a report that your inspector uses for corrosion rates and remaining life.
What surface preparation does UT need?
The surface should be free of loose scale, flaking paint and heavy rust so the probe couples properly. Thin, well-bonded coatings can often be measured through, but the procedure states when this is acceptable, and rough corrosion may need wire brushing or grinding first.
How accurate are ultrasonic thickness readings on pitted steel?
Accuracy depends on calibration, probe choice and surface condition. Dual-element probes and an A-scan display help on pitted wall, but a probe reads only the metal beneath it, so the grid spacing in the procedure matters. The report states what the survey could and could not reach.
Can you train our Midland technicians in ultrasonic testing?
Yes. We offer UT Level 1 and Level 2 training built around SNT-TC-1A, with simulator practice, and we can help you write the employer's written practice. Under SNT-TC-1A your company certifies its own personnel after the required training and experience.
Inspection and training around Midland
- Magnetic particle inspection (MT) in Midland
- Liquid penetrant testing (PT) in Midland
- Ultrasonic inspection services
- NDT inspection services in Texas
UT by industry for Midland: Pipeline · Oilfield & Drilling · Wind Energy.
UT by job: Ultrasonic pipe thickness testing · Ultrasonic weld inspection · Ultrasonic boiler tube thickness testing · Ultrasonic testing of castings and forgings.
Training your own technicians: UT Level 1 training · UT Level 2 training · NDT training for Midland technicians.
Request an UT inspection quote for Midland
Send the component and material, the quantity, the code or specification and the site address. We reply within one business day with the scope, the mobilization plan and a quote. Request a quote for ultrasonic testing in Midland.
Need ultrasonic testing (UT) done, or learned?
Atlantis provides ultrasonic testing (UT) as an inspection service, trains technicians in it, and lets teams practise it on the Practical NDT simulator.