{"id":"1379","title":"Conventional NDT Myths: 23 Misconceptions Corrected","slug":"conventional-ndt-myths","author":"Atlantis NDT","category":"NDT Methods","metaDescription":"23 conventional NDT myths about UT, MT, PT, RT, VT and SNT-TC-1A certification, each corrected with the physics or the code reference behind it.","snippet":"23 conventional NDT myths about UT, MT, PT, RT, VT and SNT-TC-1A certification, each corrected with the physics or the code reference behind it.","content":"<p><strong>Short answer:</strong> Most conventional NDT mistakes come from asking a method to do more than its physics allows. UT, MT, PT, RT and VT each detect certain flaws in certain materials under controlled conditions, and none proves a part is flawless. The governing code, the written procedure and the employer&apos;s written practice decide what is examined, by whom and what passes.</p><p>The myths below are the ones Level IIIs hear on job sites, in audits and in purchasing meetings. Each has cost someone a missed crack, a repeated examination or an audit finding. For each one you get the reality, the physics or code behind it, and what to do instead.</p><h2>General myths about NDT results</h2><h3>Myth: If the part passed NDT, it has no flaws</h3><p>A pass means no indication exceeded the acceptance criteria of the code or specification that applies. It does not mean nothing was there. ASTM E1316, the terminology standard for NDT, keeps the words apart on purpose: a discontinuity is any interruption in the material, a flaw is a discontinuity that may be detectable but is not necessarily rejectable, and a defect is a flaw that fails the acceptance criteria. Codes accept small rounded indications and ignore indications below a relevance size, and every method has a detection threshold below which a real flaw gives no signal at all. Read a clean report as &quot;nothing rejectable was found, by this method, at this sensitivity, over this surface or volume.&quot;</p><h3>Myth: ASME Section V tells you whether a weld is acceptable</h3><p>Section V tells you how to examine: procedure content, calibration, technique and personnel rules for each method. Acceptance comes from the code that references it, such as ASME Section VIII for pressure vessels, ASME B31.3 for process piping or API 1104 for pipelines. AWS D1.1 carries its own examination and acceptance rules for structural steel. The same radiograph or PT indication can pass under one code and fail under another, so a procedure that names Section V but no acceptance code is incomplete.</p><h3>Myth: More NDT methods always make equipment safer</h3><p>Safety comes from matching the method to the damage you expect, not from stacking methods. MT and PT do nothing for internal wall loss, a thickness gauge does nothing for a surface crack, and heat exchanger tubes get eddy current testing (ET) or IRIS because no surface method can reach them. Every method has a probability of detection below one and a false-call rate above zero, so a poorly matched method adds access time and false calls without adding much detection. Start from the damage mechanisms (API RP 571 catalogs them for refining equipment), then choose the method, technique and coverage that can find that damage at a size that matters.</p><h3>Myth: NDT tells you why a part failed</h3><p>NDT locates and sizes discontinuities. It cannot tell you whether a crack is fatigue, stress corrosion or hydrogen damage, or why it started. That takes a metallurgical failure analysis: fractography, metallography, hardness and chemistry. NDT still earns its place in an investigation by mapping how far similar damage has spread in sister components, but it answers &quot;where and how big,&quot; not &quot;why.&quot;</p><h2>Ultrasonic testing (UT) myths</h2><h3>Myth: UT finds everything radiography finds</h3><p>UT and RT respond to different physics. Ultrasound reflects most strongly from planar flaws that face the beam, such as lack of sidewall fusion and cracks, and it gives their depth. Radiography records differences in material along the beam, so it shows volumetric flaws such as porosity and slag clearly and leaves an image anyone can re-read. Fine scattered porosity can return weak, hard-to-characterize echoes, and thin sections, coarse-grained austenitic welds and awkward geometry all limit UT coverage. ASME Section VIII Division 1 and several other codes allow UT in place of radiography, but only under the conditions they set, typically a qualified procedure with recorded data. The <a href=\"/blog/rt-vs-ut-complete-comparison\">RT vs UT comparison</a> works through the trade-offs.</p><h3>Myth: A thickness gauge reads true wall through any coating</h3><p>In standard pulse-echo mode a gauge times the round trip from the top of the paint to the back wall and converts it using the velocity of steel. Paint carries sound at less than half that speed, so Evident&apos;s application note puts the error at more than twice the paint thickness. Echo-to-echo mode removes the coating by timing successive back-wall echoes, but it needs more than one clean back-wall echo, which a badly corroded back wall may not give. Thick or loose coatings still come off at the reading point. Write the procedure against ASTM E797 and have the report state the mode used.</p><h3>Myth: A bigger echo means a bigger flaw</h3><p>Echo amplitude depends on a flaw&apos;s orientation, shape, roughness and distance as much as its size. A tight crack tilted away from the beam can return less signal than a small, smooth reflector facing it. Amplitude methods such as distance-amplitude correction (DAC) work for detection and for a code&apos;s recording and acceptance levels, but they are a poor way to measure crack height. When height matters, for example in an engineering assessment by the owner&apos;s engineer, use a technique that measures it: the 6 dB drop for length, and tip diffraction or TOFD for through-wall height.</p><h2>Magnetic particle testing (MT) myths</h2><h3>Myth: Magnetic particle testing works on stainless steel</h3><p>Only on some grades. MT needs a ferromagnetic material. Ferritic grades such as 430 and martensitic grades such as 410 respond; austenitic grades such as 304 and 316 do not, and ASTM E1444 names austenitic stainless steel as a material the method does not apply to. Duplex grades are partly magnetic and give uneven, unreliable fields. Use penetrant testing on austenitic and duplex welds, and expect false indications at the fusion line of a dissimilar-metal weld, where permeability changes. The <a href=\"/blog/mt-vs-pt-comparison\">MT vs PT comparison</a> covers the choice in detail.</p><h3>Myth: A yoke that lifted the test weight once is good for every job</h3><p>The lift check proves the yoke produced a minimum field at the pole spacing used for the check, on that day. It does not prove the field is adequate or correctly oriented on your part, and it does not survive a dropped yoke or a damaged cable. Check lift before use, at the widest pole spacing you will actually use (an AC yoke must lift at least 10 lb, or 4.5 kg), with a weight of verified mass. Then confirm the field on the part with the field indicator or artificial-flaw shim the procedure names.</p><h3>Myth: An AC yoke finds subsurface flaws</h3><p>Alternating current magnetizes a thin skin at the surface. The changing field induces eddy currents that oppose it, so flux below the surface falls away quickly, and Iowa State&apos;s NDE-Ed resource recommends AC only when the examination is limited to surface flaws. That makes AC yokes excellent for surface cracks at weld toes and poor for anything buried. DC or half-wave DC pushes the field deeper, but even then MT reaches only slightly below the surface. Flaws deeper in the wall belong to UT.</p><h2>Liquid penetrant testing (PT) myths</h2><h3>Myth: Penetrant testing can find subsurface flaws</h3><p>Penetrant enters a flaw by capillary action, so the flaw must be open to the surface and clean. A crack just below the surface gives no indication, and neither does a surface crack whose mouth has been closed. Power wire brushing, shot blasting and grit blasting smear metal across crack openings, and the National Board&apos;s guidance on PT says that smeared metal must be removed before testing. On ferromagnetic steel, MT also reaches slightly below the surface; for anything deeper, use UT or RT.</p><h3>Myth: A longer penetrant dwell is always better</h3><p>Dwell has a minimum, set by the procedure for the material, the flaw type and the temperature, and a practical maximum: the penetrant must not dry on the surface. Dried penetrant is hard to remove from the background and is not drawn back out of the flaw by the developer, which means high background, false calls or lost indications. If a long dwell is needed, the procedure says how to keep the surface wet, usually by reapplying penetrant.</p><h3>Myth: Penetrant works the same at any temperature</h3><p>Temperature changes viscosity, evaporation and developer drying. ASTM E1417 and ASME Section V Article 6 work to a standard range of about 40 to 125 &#xB0;F (roughly 4 to 52 &#xB0;C). In Magnaflux&apos;s low-temperature trials, suggested dwell roughly doubled at 45 &#xB0;F and developer took about five times longer to dry at 40 &#xB0;F. Outside the standard range the procedure must be qualified for the temperature actually present, or another method chosen.</p><h2>Radiographic testing (RT) myths</h2><h3>Myth: Radiography is always the better weld method</h3><p>Radiography is strong on porosity, slag and root condition, and it leaves a permanent image. It is weak on tight planar flaws that do not lie along the beam, including lack of sidewall fusion on a bevel face and many cracks, and it gives no depth. It also needs radiation exclusion zones that stop other work nearby. For thick welds where planar flaws are the credible risk, UT with recorded data is often the better choice. In the USA, Atlantis does not perform radiography: where a code calls for it, the owner hires a licensed radiography contractor. For US work we offer UT where the code and the owner allow it, and an ASNT Level III review of the radiographs your contractor produces.</p><h3>Myth: If the IQI is visible, any crack would show too</h3><p>An image quality indicator proves the technique reached a stated sensitivity on an artificial feature, a hole or a wire of known size. It does not prove that a crack of similar size would be visible. A crack&apos;s visibility depends on its opening width and its angle to the beam, so a tight crack angled away from the beam can be invisible on a film whose 2-2T hole is perfectly clear. Treat the IQI as a check on technique, together with density and coverage, and add UT where planar flaws are the concern.</p><h2>Visual testing (VT) myths</h2><h3>Myth: Visual testing is just looking</h3><p>Code visual examination is a controlled method. ASME Section V Article 9 sets the conditions for direct examination: the eye within about 24 in. (600 mm) of the surface at an angle of at least 30 degrees, and at least 100 foot-candles (1,000 lux) at the surface, checked with a light meter. Remote tools such as borescopes must resolve at least as well as direct viewing. Under SNT-TC-1A, VT is a method like any other, with its own training, experience, examinations and vision checks.</p><h3>Myth: A weld that looks good is sound</h3><p>VT sees the surface: profile, undercut, overlap, surface porosity, cracks and arc strikes. It cannot see lack of fusion, slag or porosity inside the weld, which is why codes add volumetric examination where internal soundness matters. VT is still the least expensive examination on any job, and it catches problems before they are buried: fit-up, preheat, interpass cleaning and bead profile are visual checks made before and during welding, not only after.</p><h2>Certification and training myths</h2><h3>Myth: ASNT certifies technicians, so an ASNT card is good anywhere</h3><p>Under SNT-TC-1A, certification is the employer&apos;s responsibility, under the employer&apos;s written practice, and ASNT&apos;s published interpretations say exactly that. ASNT publishes the recommended practice and runs third-party programs such as ASNT NDT Level III and ASNT 9712, but those credentials do not replace the employer&apos;s certification. A Level III certified under SNT-TC-1A still takes the specific examination on the employer&apos;s own codes, procedures and products. An ASNT certificate shows tested knowledge; it does not authorize work for a company that has not certified you.</p><h3>Myth: Your certification moves with you to a new employer</h3><p>It does not. SNT-TC-1A treats the employer&apos;s certification as revoked when employment ends. What travels with you is the evidence: training records, experience logs, examination results, vision records and any third-party certificate. A new employer can use that evidence to certify you under its own written practice, on the conditions that practice sets. Keep copies of everything, because rebuilding experience hours after the fact is where most delays start.</p><h3>Myth: SNT-TC-1A is a law</h3><p>SNT-TC-1A is a recommended practice, and ASNT itself stresses that it is not a standard. It becomes binding when a code, regulation or contract invokes it, and then through the employer&apos;s written practice, which may adapt its details but may not drop its basic provisions: training, experience, examination and recertification. AWS D1.1, for example, references SNT-TC-1A and CP-189 for NDT personnel, and many owner specifications name SNT-TC-1A in purchase orders. ANSI/ASNT CP-189 is the consensus standard alternative.</p><h3>Myth: Online training cannot count toward SNT-TC-1A</h3><p>The 2020 edition of SNT-TC-1A lists computer-based and web-based training among the forms organized training may take, and the employer must make sure outside training meets its written practice. What online training cannot do is replace the parts SNT-TC-1A treats separately: documented experience hours in the method and a hands-on practical examination on real specimens. A browser simulator such as <a href=\"/practical-ndt\">Practical NDT</a> is useful practice, but simulator time is not experience and it is not the practical exam.</p><h3>Myth: A Level II can approve NDT procedures</h3><p>SNT-TC-1A describes a Level III as capable of developing, qualifying and approving procedures, while a Level II sets up, calibrates, performs and interprets examinations to approved procedures. ASNT has said that who must approve a procedure is outside the scope of SNT-TC-1A, so the answer comes from the code, the client specification and your written practice, and most of them name a Level III. A procedure signed only by a Level II is a common audit finding. Our <a href=\"/consulting/ndt-technical-procedure-development\">NDT procedure development</a> service covers writing, demonstration and Level III approval.</p><h3>Myth: One vision exam covers every job</h3><p>SNT-TC-1A recommends a near-vision check reading Jaeger J-2 (or equivalent) at not less than 12 in., done annually, plus a color-contrast check for the colors or shades of gray used in the method, as the employer determines. Other documents differ: CP-189 asks for the smaller J-1 line, and AWS D1.1 sets its own eye examination for welding inspectors. Track each requirement against the work the person actually does and keep the records; see <a href=\"/consulting/ndt-vision-examination-records\">NDT vision examination records</a>.</p><h2>Conventional NDT myths and realities at a glance</h2><table><thead><tr><th>Myth</th><th>Reality</th><th>Reference</th></tr></thead><tbody><tr><td>A pass means no flaws</td><td>A pass means nothing exceeded the acceptance criteria at the method&apos;s sensitivity</td><td>ASTM E1316; the acceptance code</td></tr><tr><td>Section V sets acceptance</td><td>Section V sets how to examine; the referencing code sets acceptance</td><td>ASME Section V; Section VIII, B31.3, API 1104</td></tr><tr><td>More methods are always safer</td><td>Match the method to the expected damage mechanism</td><td>API RP 571</td></tr><tr><td>NDT explains failures</td><td>NDT finds and sizes; metallurgy explains cause</td><td>Failure analysis practice</td></tr><tr><td>UT finds all RT finds</td><td>UT favors planar flaws, RT favors volumetric flaws</td><td>Physics; ASME VIII-1 UT-in-lieu rules</td></tr><tr><td>Gauges read through any coating</td><td>Pulse-echo adds over twice the paint thickness; use echo-to-echo or remove coating</td><td>ASTM E797; gauge maker data</td></tr><tr><td>Bigger echo, bigger flaw</td><td>Amplitude depends on orientation; size height by tip diffraction or TOFD</td><td>UT physics</td></tr><tr><td>MT works on stainless</td><td>Not on austenitic grades; unreliable on duplex</td><td>ASTM E1444</td></tr><tr><td>One lift test is enough</td><td>Check before use at working pole spacing, then verify the field on the part</td><td>ASME Section V Article 7; ASTM E709</td></tr><tr><td>AC yokes find subsurface flaws</td><td>AC skin effect limits it to surface flaws</td><td>Electromagnetic physics</td></tr><tr><td>PT finds subsurface flaws</td><td>Only flaws open to a clean surface</td><td>Capillary physics; National Board guidance</td></tr><tr><td>Longer dwell is better</td><td>Penetrant must never dry; follow procedure limits</td><td>ASME Section V Article 6</td></tr><tr><td>PT works at any temperature</td><td>Standard range about 40 to 125 &#xB0;F; qualify outside it</td><td>ASTM E1417; ASME Section V Article 6</td></tr><tr><td>RT is always better for welds</td><td>RT misses many tight planar flaws and gives no depth</td><td>Radiographic physics</td></tr><tr><td>Visible IQI means cracks would show</td><td>The IQI proves technique sensitivity, not crack detection</td><td>ASME Section V Article 2</td></tr><tr><td>VT is just looking</td><td>Distance, angle, light and resolution are controlled</td><td>ASME Section V Article 9</td></tr><tr><td>A good-looking weld is sound</td><td>VT sees only the surface</td><td>Weld examination practice</td></tr><tr><td>ASNT certifies technicians</td><td>The employer certifies under its written practice</td><td>SNT-TC-1A; ASNT interpretations</td></tr><tr><td>Certification moves with you</td><td>It ends with employment; the evidence travels</td><td>SNT-TC-1A</td></tr><tr><td>SNT-TC-1A is a law</td><td>It is a recommended practice that binds when invoked</td><td>SNT-TC-1A; AWS D1.1</td></tr><tr><td>Online training cannot count</td><td>Web-based training can count; experience and the practical cannot be online</td><td>SNT-TC-1A 2020</td></tr><tr><td>A Level II can approve procedures</td><td>Code, contract and written practice decide; most require a Level III</td><td>SNT-TC-1A; ASNT interpretations</td></tr><tr><td>One vision exam fits all</td><td>J-2 under SNT-TC-1A, J-1 under CP-189, separate D1.1 rules</td><td>SNT-TC-1A; CP-189; AWS D1.1</td></tr></tbody></table><h2>How to keep these myths off your own jobs</h2><p>Most of the problems above are caught on paper before anyone mobilizes. Have a Level III check that each procedure names the acceptance code, the technique and its limits, and that the people doing the work are certified for that technique under a current written practice. Then check the method against the damage mechanism, not habit.</p><ul><li>Method detail, scope and limits: <a href=\"/ultrasonic-testing\">ultrasonic testing</a>, <a href=\"/magnetic-particle-testing\">magnetic particle testing</a>, <a href=\"/penetrant-testing\">penetrant testing</a>, <a href=\"/visual-testing\">visual testing</a> and <a href=\"/radiographic-testing\">radiographic testing</a>.</li><li>Written practices, procedures and audit preparation through <a href=\"/consulting/ndt-consulting-level-iii\">outsourced ASNT NDT Level III consulting</a> and <a href=\"/ndt-written-practice-development\">written practice development</a>.</li><li>Training to SNT-TC-1A: <a href=\"/ndt-level-2-training\">NDT Level 2 training</a> with self-paced theory and Level III Q&amp;A, the Practical NDT simulator, and the hands-on practical at your own facility. Check where you stand with the <a href=\"/snt-tc-1a-eligibility\">SNT-TC-1A eligibility checker</a> and the free <a href=\"/ndt-practice-tests\">NDT practice tests</a>.</li></ul><p>Atlantis NDT works remotely from Houston and on site when an examination, audit or inspection needs it. Send your procedure, written practice or scope and we reply within one business day.</p>","updatedAt":"2026-11-17"}